The difference in the handlers was that in the
NETDEV_EVENT_DISCONNECT_BY_AP case we would make sure to reply
to a pending dbus Connect call. We also need to do that for
NETDEV_EVENT_DISCONNECT_BY_SME. This happens if another process
sends an nl80211 disconnect command while we're connecting.
The eapol handshake timeout can now be configured in main.conf
(/etc/iwd/main.conf) using the key eapol_handshake_timeout. This
allows the user to configure a long timeout if debugging.
If --gdb is used with test-runner, all the timeouts in the
IWD class must be turned off otherwise the test will fail.
Inside test-runner, a environment variable (IWD_TEST_TIMEOUTS)
is set to either 'on' or 'off'. Then the IWD class (and any
others) can handle the timeouts accordingly. Note that this
does not turn off dbus timeouts, rather it ignores timeout
failures. This does mean that ultimately the test will most
likely fail due to a dbus timeout, but it at least gives you
unlimited debugging time.
Without this subsequent tests may be affected by hwsim not being
restarted.
Additionally in 4.13 the kernel will not use the registered hwsim
wmedium for wiphys created after the HWSIM_CMD_REGISTER call and
there's no way to re-register it without disconnecting from netlink
which is a bit of work. It's a one line fix in 4.13, I've not yet
checked if this has changed in current git.
When running multiple BSSes in one ESS this solves the communication
between them (called RRB) for purposes like preauthentication,
FT key pull and push and FT-over-DS without complicated bridges. At the
same time we're unlikely to have a scenario where we need the
communication to fail so there's no need for this to be configurable.
The supporting code for multiple hostapd processes is left in place so
that configure_hostapd_instances can decide how many processes to run
based on hw.conf and policies. start_hostapd now uses "-i wln0,..."
which is no longer documented in hostapd manual page or usage() but
still supported in current git and required if interface names are not
provided in the config files (possibly unless -b is used which is also
undocumented.)
After an EAP exchange rsn_info would be uninitialized and in the FT case
we'd use it to generate the step 2 IEs which would cause an RSNE
mismatch during FT handshake.
Until now we'd save the second 32 bytes of the MSK as the PMK and use
that for the PMK-R0 as well as the PMKID calculation. The PMKID
actually uses the first 32 bytes of the PMK while the PMK-R0's XXKey
input maps to the second 32 bytes. Add a pmk_len parameter to
handshake_state_set_pmk to handle that. Update the eapol_eap_results_cb
802.11 quotes to the 2016 version.
handshake_state_install_ptk triggers a call to
netdev_set_pairwise_key_cb which calls netdev_connect_ok, so don't call
netdev_connect_ok after handshake_state_install_ptk. This doesn't fix
any specific problem though.
If the request being cancelled by agent_request_cancel has already been
sent over dbus we need to reset pending_id, the timeout, call l_dbus_cancel
to avoid the agent_receive_reply callback (and crash) and perhaps start
the next request. Alternatively we could only reset the callback and not
free the request, then wait until the agent method to return before starting
the next request.
Move the cancelling of the eapol timeout from the end of step 1 to
step 3 to guard the whole handshake. At the end of step 1 stop the
EAPOL-Start timeout for the case of 802.1X authentication + a cached
PMKSA (not used yet.)
Some APs respond to Neighbor Report Requests with neighbor reports that
have a zero operating class value and a non-zero channel number. This
does not mean that the channel is in the same band that the reporting
AP operates in. Try to guess the band that the channel refers to out of
2.4 and 5GHz -- the bands supported by those APs.
wpa_supplicant also has this workaround in place.
