adhoc_reset() destroys ssid and sta_states but leaves the pointers
around, athough the adhoc_state structure is not always freed.
This causes a segfault when exiting iwd after a client has done
adhoc start and adhoc stop on a device since adhoc_reset() is called
from adhoc_sta_free although it was previously called from
adhoc_leave_cb().
The netdev_leave_adhoc() returns a negative errno on errors and zero
on success, but adhoc_dbus_stop() assumed the inverse when checking for
an error.
Also, the DBus message was not being referenced in adhoc->pending and
then adhoc_leave_cb() segfaulted attempting to dereference it.
It seems some APs send the IGTK key in big endian format (it is a
uin16). The kernel rightly reports an -EINVAL error when iwd issues a
NEW_KEY with such a value, resulting in the connection being aborted.
Work around this by trying to detect big-endian key indexes and 'fixing'
them up.
This bug has been in here since OWE was written, but a similar bug also
existed in hostapd which allowed the PTK derivation to be identical.
In January 2020 hostapd fixed this bug, which now makes IWD incompatible
when using group 20 or 21.
This patch fixes the bug for IWD, so now OWE should be compatible with
recent hostapd version. This will break compatibility with old hostapd
versions which still have this bug.
If the AP only supports an AKM which requires an auth protocol
CMD_AUTHENTICATE/CMD_ASSOCIATE must be supported or else the
auth protocol cannot be run. All the auth protocols are started
assuming that the card supports these commands, but the support
was never checked when parsing supported commands.
This patch will prevent any fullMAC cards from using
SAE/FILS/OWE. This was the same behavior as before, just an
earlier failure path.
This function was intended to catch socket errors and destroy the group
but it would leak the l_io object if that happened, and if called on
ordinary shutdown it could cause a crash. Since we're now assuming
that the netlink socket operations never fail just remove it.
Only add constants for parsing the Device Information subelement as that
is the main thing we care about in P2P code. And since our own WFD IEs
will likely only need to contain the Device Information subelement, we
don't need builder utilities. We do need iterator utilities because we
may receive WFD IEs with more subelements.
In some cases a P2P peer will ACK our frame but not reply on the first
attempt, and other implementations seem to handle this by going back to
retransmitting the frame at a high rate until it gets ACKed again, at
which point they will again give the peer a longer time to tx the
response frame. Implement the same logic here by adding a
retries_on_ack parameter that takes the number of additional times we
want to restart the normal retransmit counter after we received no
response frame on the first attempt. So passing 0 maintains the
current behaviour, 1 for 1 extra attempt, etc.
In effect we may retransmit a frame about 15 * (retry_on_ack + 1) *
<in-kernel retransmit limit> times. The kernel/driver retransmits a
frame a number of times if there's no ACK (I've seen about 20 normally)
at a high frequency, if that fails we retry the whole process 15 times
inside frame-xchg.c and if we still get no ACK at any point, we give up.
If we do get an ACK, we wait for a response frame and if we don't get
that we will optionally reset the retry counter and restart the whole
thing retry_on_ack times.
In order to support AlwaysRandomizeAddress and AddressOverride, station will
set the desired address into the handshake object. Then, netdev checks if
this was done and will use that address rather than generate one.
This patch adds two new options to a network provisioning file:
AlwaysRandomizeAddress={true,false}
If true, IWD will randomize the MAC address on each connection to this
network. The address does not persists between connections, any new
connection will result in a different MAC.
AddressOverride=<MAC>
If set, the MAC address will be set to <MAC> assuming its a valid MAC
address.
These two options should not be used together, and will only take effect
if [General].AddressRandomization is set to 'network' in the IWD
config file.
If neither of these options are set, and [General].AddressRandomization
is set to 'network', the default behavior remains the same; the MAC
will be generated deterministically on a per-network basis.
Since frame_watch_remove_by_handler only forgets a given function +
user data pointers, and doesn't remove the frame prefixes added in the
kernel, we can avoid later re-registering those prefixes with the
kernel by keeping them in our local watchlist, and only replacing the
handler pointer with a dummy function.
If during WATCHLIST_NOTIFY{,_MATCHES,_NO_ARGS} one of the watch
notify callback triggers a call to watchlist_destroy, give up calling
remaining watches and destroy the watchlist without crashing. This is
useful in frame-xchg.c (P2P use case) where a frame watch may trigger
a move to a new state after receiving a specific frame, and remove one
group of frame watches (including its watchlist) to create a different
group.
For privacy reasons its advantageous to randomize or mask
the MAC address when connecting to networks, especially public
networks.
This patch allows netdev to generate a new MAC address on a
per-network basis. The generated MAC will remain the same when
connecting to the same network. This allows reauthentications
or roaming to work, and not have to fully re-connect (which would
be required if the MAC changed on every connection).
Changing the MAC requires bringing the interface down. This does
lead to potential race conditions with respect to external
processes. There are two potential conditions which are explained
in a TODO comment in this patch.
This API is being added to support per-network MAC address
generation. The MAC is generated based on the network SSID
and the adapters permanent address using HMAC-SHA256. The
SHA digest is then constrained to make it MAC address
compliant.
Generating the MAC address like this will ensure that the
MAC remains the same each time a given SSID is connected to.
Make sure a frame callback is free to call frame_xchg_stop without
causing a crash. Frame callback here means the one that gets
called if our tx frame was ACKed and triggered a respone frame that
matched one of the provided prefixes, within the given time.
All in all a frame callback is allowed to call either
frame_xchg_stop or frame_xchg_startv or neither. Same applies to
the final callback (called when no matching responses received).
Don't crash if the user calls frame_xchg_stop(wdev) from inside the
frame exchange's final callback. That call is going to be redundant but
it's convenient to do this inside a cleanup function for a given wdev
without having to check whether any frame exchange was actually running.
This API was updated to take an extra boolean which will
automatically power up the device while changing the MAC
address. Since this is what IWD does anyways we can avoid
the need for an intermediate callback and go right into
netdev_initial_up_cb.
iwd would fail to connect using EAP-TLS when no CA certificate was
provided as it checked for successful loading of the CA certificate
instead of the client certificate when attempting to load the client
certificate.
The password for EAP-GTC is directly used in an EAP response. The
response buffer is created on the stack so an overly large password
could cause a stack overflow.
mac80211 drivers seem to send the disconnect event which is triggered by
CMD_DISCONNECT prior to the CMD_DISCONNECT response. However, some
drivers, namely brcmfmac, send the response first and then send the
disconnect event. This confused iwd when a connection was immediately
triggered after a disconnection (network switch operation).
Fix this by making sure that connected variable isn't set until the
connect event is actually processed, and ignore disconnect events which
come after CMD_DISCONNECT has alredy succeeded.
For nl80211 sockets other than our main l_genl object use socket io
directly, to avoid creating many instances of l_genl. The only reason
we use multiple sockets is to work around an nl80211 design quirk that
requires closing the socket to unregister management frame watches.
Normally there should not be a need to create multiple sockets in a
program.
Add a little state machine and a related API, to simplify sending out a
frame, receiving the Ack / No-ack status and (if acked) waiting for a
response frame from the target device, one of a list of possible
frame prefixes. The nl80211 API for this makes it complicated
enough that this new API seems to be justified, on top of that there's a
quirk when using the brcmfmac driver where the nl80211 response
(containing the operation's cookie), the Tx Status event and the response
Frame event are received from nl80211 in reverse order (not seen with
other drivers so far), further complicating what should be a pretty
simple task.
Try to better deduplicate the frame watches. Until now we'd check if
we'd already registered a given frame body prefix with the kernel, or a
matching more general prefix (shorter). Now also try to check if we
have already have a watch with the same callback pointer and user_data
value, and:
* an identical or shorter (more general) prefix, in that case ignore
the new watch completely.
* a longer (more specific) prefix, in that case forget the existing
watch.
The use case for this is when we have a single callback for multiple
watches and multiple frame types, and inside that callback we're looking
at the frame body again and matching it to frame types. In that case
we don't want that function to be called multiple times for one frame
event.
In frame_watch_group_remove I forgot to actually match the group to be
removed by both wdev_id and group_id. group_ids are unique only in the
scope of one wdev.
I forgot to actually add new groups being created in
frame_watch_group_get to the watch_groups queue, meaning that we'd
re-create the group every time a new watch was added to the group.
Processing the duplicated TLVs while connecting to a malicious AP may lead
to overflow of the response buffer. This patch ensures that the
duplicated TLVs are not parsed.
The pending wiphy state 'use_default' variable was not set early enough
in some circumstances resulting in weird behavior for blacklisted
drivers. Fix this by adding a manager_wiphy_dump_done callback which
will properly initialize the use_default value.
Fixes: c4b2f10483 ("manager: Handle missing NEW_WIPHY events")
brcmfmac does not allow the removal of the default / primary interface.
So there isn't much point in having iwd attempt this.
Another issue is that brcmfmac _does_ allow the deletion of non-default
interfaces. So starting iwd on a system with a station & ap interface
active can result in iwd attempting to delete all the interfaces. Given
the above, it succeeds in deleting the ap interface but not the station
one. In strange circumstances it might end up thinking that the ap
interface is the 'default' and trying to use it, whereas it was just
successfully removed.
==192== Conditional jump or move depends on uninitialised value(s)
==192== at 0x4531D3: l_queue_find (queue.c:346)
==192== by 0x42F1F8: manager_config_notify (manager.c:667)
==192== by 0x45A895: process_multicast (genl.c:970)
==192== by 0x45A895: received_data (genl.c:1037)
==192== by 0x4577B2: io_callback (io.c:126)
==192== by 0x456B0D: l_main_iterate (main.c:473)
==192== by 0x456BCB: l_main_run (main.c:520)
==192== by 0x456DDA: l_main_run_with_signal (main.c:642)
==192== by 0x4034B0: main (main.c:497)
The kernel emits NEW_WIPHY events whenever a new wiphy is registered.
Unfortunately these events are emitted under the 'legacy' semantics and
have a hard size limit of 4096 bytes. Unfortunately, it is possible for
a NEW_WIPHY message to exceed this limit (ath10k cards seem to be
affected in particular), which results in the kernel never sending these
messages out. This can lead to NEW_INTERFACE events being emitted with
a wiphy_id that had no corresponding NEW_WIPHY event emitted. Such a
sequence can confuse iwd's hardware detection logic, particularly during
hot-plug or system boot.
Fix this by re-dumping the wiphy if such a condition is detected. This
has some interaction with blacklisted wiphys, so the wiphy objects are
now always tracked and marked as blacklisted. Before, the blacklisted
wiphys were simply not added to the iwd list of tracked wiphys.
For the inner EAP methods that support generation of the key material
include it into imck generation. This allows to cryptographically
bind the inner method with the tunnel.
Windows Server 2008 - Network Policy Server (NPS) generates an invalid
Compound MAC for Cryptobinding TLV when is used within PEAPv0 due to
incorrect parsing of the message containing TLS Client Hello.
Setting L bit and including TLS Message Length field, even for the
packets that do not require fragmentation, corrects the issue. The
redundant TLS Message Length field in unfragmented packets doesn't
seem to affect the other server implementations.
Sometimes, at least with brcmfmac, the default interface apparently
takes a moment to get created after the NEW_WIPHY event. We didn't
really consider this case in the NEW_WIPHY handler and we've got a race
condition. It fixes the following bug for me:
https://bugs.archlinux.org/task/63912 -- tested by removing and
re-modprobing the brcmfmac module rather than rebooting.
To work around this wait for the NEW_INTERFACE event and then retry the
setup. We still do the initial attempt directly after NEW_WIPHY to
handle cases like wiphys with no default interfaces and pre-existing
wiphys.
We track mtime as the 'LastConnectedTime' of the network, and also sort
the known network list according to the last connected time.
Unfortunately we were never reacting to ATTRIB changes, and so were
never updating the network_info->connected_time whenever a network was
connected to.
Rework the logic to address this. This also fixes a small bug where the
connected_time was not set properly prior to removal / re-insertion of
the network_info.
We use the mtime on the network profile as the 'Last Connected Time'.
When we update any property and sync the file to disk, the mtime was not
preserved (since we were creating a new temporary file instead of
modifying the old one). This led to LastConnectedTime property change
being emitted / updated incorrectly when a writable property on the
KnownNetwork interface was updated.
Our design preference is to not call any callbacks in the _free/_destroy
method of a class (with the exception of explicit destroy callbacks
provided, if any).
Invoking the callback in this case was unnecessary: wsc_dbus_free was
already replying to pending connect / cancel messages. The only other
thing the callback would attempt to do is to set station back into
autoconnect mode. This was unnecessary as well since the netdev is
already down.
This change removes the callback invocation. Since wsc_enrollee_destroy
is now just calling wsc_enrollee_free, remove this from the API and
expose wsc_enrollee_free instead.
Split the WSC D-Bus interface class (struct wsc) into a base class
common to station mode and P2P mode (struct wsc_dbus) and station-
specific logic like scanning, saving the credentials as a known network
and triggering the station-mode connection (struct wsc_station_dbus).
Make the base class and its utilities public in wsc.h for P2P use.
Create struct wsc_enrollee which is allocated with wsc_enrollee_new,
taking a done callback as a parameter. The callback is always
called so there's no need for a separate destroy callback. The object
only lives until the done callback happens so wsc_enrollee_cancel/destroy
can only be used before this.
Looks like the rest of the file is simplified thanks to this.
This new API is independent of netdev.c and allows actually
unregistering from receiving notifications of frames, although with some
quirks. The current API only allowed the callback for a registration to
be forgotten but our process and/or the kernel would still be woken up
when matching frames were received because the kernel had no frame
unregister call. In the new API you can supply a group-id paramter when
registering frames. If it is non-zero the frame_watch_group_remove() call
can be used to remove all frame registrations that had a given group-id
by closing the netlink socket on which the notifications would be
received. This means though that it's a slightly costly operation.
The file is named frame-xchg.c because I'm thinking of also adding
utilities for sending frames and waiting for one of a number of replies
and handling the acked/un-acked information.
Instead of taking the credentials from wsc object directly, have the
caller pass these in. This makes it more consistent with how the
done_cb was done.
Split the interface-specific logic from the core WSC logic. The core
WSC code is the part that we can re-use between P2P and station and
doesn't include the D-Bus code, scanning for the target BSS or the
attempt to make a station mode connection.
Allow netdev_create_from_genl callers to draw a random or non-random MAC
and pass it in the parameter instead of a bool to tell us to generating
the MAC locally. In P2P we are generating the MAC some time before
creating the netdev in order to pass it to the peer during negotiation.
Some server implementation don't seem to provide the valid compound MACs.
In the meantime, iwd will ignore the invalid Crypto-Binding TLVs as their
usage is optional.
The intent was to check for the presence of the add_domain_name
operation, not add_dns operation.
Fixes: 930528e35e ("resolve: Add systemd-resolved domain name installer")
It seems that the kernel uses -EOPNOTSUPP if the change_station
operation is not implemented by the driver. However, some drivers do
implement change_station and choose to report -ENOTSUPP instead of
-EOPNOTSUPP.
To add to the confusion, EOPNOTSUPP and -ENOTSUPP are the same on some
systems (e.g. Gentoo). Be paranoid and allow both errors to be ignored
when sending CMD_SET_STATION.
Fixes: 0238ffb8d9 ("netdev: Use -EOPNOTSUPP instead of -ENOTSUPP")
The first if case should be -10950, not 10950. Without the negative
this first case would get hit every time since signal strength values
are always negative.
The Crypto Binding TLV is used to ensure that the EAP peer and the
EAP server participated in both the inner and the outer EAP
authentications of a PEAP authentication by cryptographically associating
the phase 1 and phase 2 authentications.
The usage of Crypto-Binding in PEAPv0 is optional and is triggered by
the reception of the Crypto-Binding TLV from the server.
The handler for EAP Extensions has been modified to support multiple
TLV types instead of the single Result TLV. This will allow to handle
the other TLVs such as Crypto-Binding TLV.
There are some server implementations that send requests that are
not "Password" but still want us send password. This commit modify
the behavior to send a warning and still try to auth with password.
This makes me able to auth with server in my school which sends
"Enter Aruba Login".
wpa_supplicant does not check if it is "Password".
The kernel uses -EOPNOTSUPP in the case of change_station operation not
being provided. On most systems -EOPNOTSUPP is defined to be the same
as -ENOTSUPP, but seemingly not all systems.
Previously, the key was installed once the tunnel was created
despite the outcome of the second authentication phase. Now, the
key installation is delayed until the successful completion of
the second authentication phase. This excludes the unnecessary
operations in the case of a failure and key reinstallation with
cypro-binding in use.
Commit 1057d8aa74 changed the device interface creation logic
from being unconditional inside netdev.c to instead use NETDEV_WATCH_*
events. However, this broke the assumption that the device interface
was created before all others. The effect is that the scan_wdev_add
might no longer be called prior to station interface being created. Fix
this by moving scan_wdev_add/remove calls to netdev.c instead.
Fixes: 1057d8aa74 ("device: Move device creation from netdev.c to event watch")
#0 0x000055555558ee5d in scan_notify (msg=0x55555560b640, user_data=0x0) at src/scan.c:1706
#1 0x00007ffff7f2c78c in ?? () from /usr/lib/libell.so.0
#2 0x00007ffff7f299ec in ?? () from /usr/lib/libell.so.0
#3 0x00007ffff7f28e4a in l_main_iterate () from /usr/lib/libell.so.0
#4 0x00007ffff7f28efc in l_main_run () from /usr/lib/libell.so.0
#5 0x00007ffff7f290b9 in l_main_run_with_signal () from /usr/lib/libell.so.0
#6 0x00005555555639c4 in main (argc=1, argv=0x7fffffffec18) at src/main.c:497
Save the source frame type in struct scan_bss as it may affect how some
of the data in the struct will be parsed. Also replace the P2P IE
payload data in that struct with a union containing pre-parsed p2p
attributes corresponding to the frame type.
This means users don't have to call the parsers in p2putil.c on that
data, which wouldn't have worked anyway because those parsers assume
input is the raw IE sequence rather than just the "payload".
All these functions free up the resources used by the struct but don't
free the struct itself (allowing it to be static) so rename the
functions to avoid confusion.
The kernel sends NL80211_ATTR_SCAN_START_TIME_TSF with CMD_TRIGGER and
RRM requires this value for beacon measurement reports.
The start time is parsed during CMD_TRIGGER and set into the scan request.
A getter was added to obtain this time value for an already triggered
scan.
After making the change, the SCAN_ABORTED case was cleaned up a bit to
remove the local scan_request usage in favor of the one used for all the
other cases.
Create and destroy the device state struct and the DBus interfaces in a
way more similar to the Station, AdHoc and AP interfaces. Drop
netdev_get_device() and the device specific code in netdev that as far
as I can tell wasn't needed.
Check the iftype before registering ANQP on new interface.
Not that the check here and in rrm.c (which already checks the iftype)
may need to be extended to run on NETDEV_WATCH_EVENT_UP because a device
could be created with a different iftype and then have the iftype changed
before powering up.
The RCPI value was using floating point values as per the spec. But instead
we can just use the signal strength coming from the kernel in mili mdm and
scale the hard coded values by a factor of 100.
Beacon requests can specify a scan duration, and set a flag which makes
this duration mandatory. The kernel supports both these values for scan
requests so we no longer need to reject requests which contain these.
Drivers which do not support EXT_FEATURE_SET_SCAN_DWELL will ignore the
duration value, but if duration mandatory is set we must reject the
request.
The kernel allows a scan duration and duration mandatory flag to be
set in scan requests. RRM requests can contain these values so they
have been added to scan_parameters.
Scanning with drivers which do not support EXT_FEATURE_SET_SCAN_DWELL
will not include these values in scan requests.
If a scan is requested during the middle of a connection we should
return busy instead of attempting the scan. The kernel ends up coming
back with not supported in this case, which is misleading and
difficult to debug.
The module framework was changed to call the module exit functions in
the reverse order as the init functions. This uncovered/caused known
networks to try and free the network_info structures after hotspot had
already freed them. Since known networks clean up the network_info's
anyways, we don't actually need hotspot to do any cleanup.
Apparently the intention was for the dependent module's name to appear
in the variable name resulting from using IWD_MODULE_DEPENDS, so the
dependencies all have unique names (apparently not critical).
Despite that PEAPv0 spec indicates that TLS tunnel needs to be torn
down after the transmission of a secure Result response, some servers
treat this TLS close alert as a failure. This patch changes the above
behavior to explicitly torn the tunnel only in the case of
authentication failure and leave it open after the success.
The previous refactoring somehow changed the 'Settings' section name
into 'General'
Fixes: ac53239109 ("doc: Split network configuration description into separate manpage")
This module takes care of radio measurements which an AP can request.
There are many types of requests, and for now only beacon requests
are supported.
IWD will filter certain types of beacon requests that are NOT
supported:
- AP channel reports. Only single channel requests will be supported
- Autonomous measurements. Only direct requests will be supported.
IWD will not accept requets to trigger reports under certain
conditions (SNR/RSSI thresholds, etc.)
- Timed measurements. Only immediate measurements will be performed.
The accuracy for timed measurements cannot be reliably guaranteed
due to kernel scheduling/queues.
- Full reporting detail. The AP can request the STA return the full
set of IEs in a beacon. IWD does not currently save all IEs, plus
there is quite a bit of complexity involved as certain IEs get
truncated, and there are other length limitations.
There are other limitations not specific to beacon requests:
- IWD will support single measurement requests per report. Multiple
measurement request IEs can be included, but the reports will be
sent out separately.
- IWD will limit the number of requests it responds to in a given
amount of time. As it stands now this is hard coded to 2 requests
per second maximum. This will prevent DoS attacks.
- IWD will not accept any measurement requests from APs it is not
connected to, and will not accept any requests until connected.
For Radio Resource Management (RRM) we will need access to the currently
connected BSS as well as the last scan results in order to do certain
kinds of requested measurements.
netdev_connect can achieve the same effect as netdev_connect_wsc but is
more flexible as it allows us to supply additional association IEs. We
will need this capability to make P2P connections. This way we're also
moving the WSC-specific bits to wsc.c from the crowded netdev.c.
On EAP events, call the handshake_event handler with the new event type
HANDSHAKE_EVENT_EAP_NOTIFY isntead of the eapol_event callback.
This allows the handler to be set before calling
netdev_connect/netdev_connect_wsc. It's also in theory more type-safe
because we don't need the cast in netdev_connect_wsc anymore.
Convert the handshake event callback type to use variable argument
list to allow for more flexibility in event-specific arguments
passed to the callbacks.
Note the uint16_t reason code is promoted to an int when using variable
arguments so va_arg(args, int) has to be used.
no_cck_rates is set in the scan parameters generally to make sure
that the Probe Request frames are not sent at any of the 802.11b
rates during active scans. With this patch we also omit those rates
from the Supported Rates IEs, which is required by the p2p spec and
also matches our flag's name.
The current logic did not make sure that each entry provided was
actually parsed. Also add a sanity check to make sure that no duplicate
parsing occurs.
When updating the network ranking there was a potential out of bounds
array access. The condition was if known_network_offset returned a
negative value, indicating the known network was not found. Since
network->info is only set for known networks this should not ever
happen as network->info is checked prior.
Though this is likely impossible, knownnetworks is complex enough that
its better to just be paranoid and put an L_WARN_ON to check the
return.
Since the property Autoconnect was renamed to AutoConnect, change the
Autoconnect setting to match.
For now we still allow the legacy name to be used here, but a warning is
printed to remind users to update.
Relax the pre-check for local user certificate. Before we used to check
that the CA provided (if any) was used to verify both the peer identity
and the local certificate chain. However, there seem to be networks
that use different CAs to sign AP/Radius certificates and certificates
issued to users.
Drop the ca_certs argument from l_certchain_verify, but keep the call
there to make sure the certificate chain is indeed a chain as a sanity
check.
The commit/confirm processing was incorrectly subtracting 2 from
the length when they should be subtracting 6. As with the other
similar change, the length is validated with mpdu_validate so
subtracting 6 will not cause an overflow.
This function was returning a boolean and the expected return was
a signed integer. Since this function actually returned false in
all cases the check for a success (0) return always worked.
The comment about the 'standard code path' was removed as this is
no longer valid.
If an authentication frame of length <= 5 is sent sae will overflow an
integer. The original cause of this was due to incorrectly using the
sizeof(struct mmpdu_header). The header can be either 24 or 28 bytes
depending on fc.order. sizeof does not account for this so 28 is always
the calculated length.
This, in addition to hostapd not including a group number when rejecting,
cause this erroneous length calculation to be worked around as seen in
the removed comment. The comment is still valid (and described again
in another location) but the actual check for len == 4 is not correct.
To fix this we now rely on mpdu_validate to check that the authentication
frame is valid, and then subtract the actual header length using
mmpdu_header_len rather than sizeof. Doing this lets us also remove the
length check since it was validated previously.
A recent change checked the return value of ie_parse_rsne_from_data
inside the ptk 1/4 handler. This seemed safe, but actually caused
the eapol unit test to fail.
The reason was because eapol was parsing the IEs assuming they were
an RSN, when they could be a WPA IE (WPA1 not WPA2). The WPA case
does not end up using the rsn_info at all, so having rsn_info
uninitialized did not pose a problem. After adding the return value
check it was found this fails every time for WPA1.
Since the rsn_info is not needed for WPA1 we can only do the RSN
parse for WPA2 and leave rsn_info uninitialized.
The intent here was to validate that the frequency is a multiple of 5
and lies in a certain range. Somehow the channel was checked for being
a multiple of 5 instead.
The logic here intended to check whether all required attributes were
available. However, it set the parse_error to true instead of
have_required to false as intended.
Replace uses of strcpy by the safer l_strlcpy. Note that both of these
functions can only be called with a buffer of max 253 bytes (the
identity string), so this is purely a precautionary measure.
Technically there's no problem here as l_queue_remove does not
dereference the pointer. Still, it confuses certain static analysis
tools in the current form. Reordering this will not change the behavior
at all.
This was refactored to set the mtu via __eap_set_config rather than
passing the MTU into eap_init. This makes eap work in a similar fashion
as eapol (i.e. __eapol_set_config).
If __eap_set_config is not used, the MTU will be set to 1020, which is
the same as previously passing 0 to eap_init.
Since iwd_modules_init is now defered until nl80211_appeared, we can
assume the nl80211 object is available. This removes the need for
netdev_set_nl80211 completely.
In preparation for integrating IWD_MODULE into modules which require
nl80211 we move the module init into the nl80211_appeared callback.
This will guarentee that the nl80211 is available during module init
and allow modules to get their own copy of nl80211 rather than needing
a set function (e.g. netdev_set_nl80211).
Since the dbus name request callback happens before this as well any
dbus module can also use IWD_MODULE and simply assume the dbus object
is ready.
plugin_init was also deferred to nl80211_appeared since some plugins
depend on modules being initialized.
Converts agent into an IWD module. This removes the dbus dependency
on agent. Since dbus is initialized very early we can assume
dbus_get_bus is going to return a valid object.
Previously, station state 'connected' used to identify an interface associated
with AP. With the introduction of netconfig, an interface is assumed to be
connected after the IP addresses have been assigned to it. If netconfig is
disabled, the behavior remains unchanged.
Refactoring was required to allow for embedded certs. The existing
eap_tls_state object was changed to hold the cert types (l_queue,
l_certchain, l_key) rather than the file path, since there may not
actually be separate PEM files.
Care was taken to properly manage the memory of these objects.
Since the TLS object takes ownership when setting auth data or the
CA certs all error cases must be handled properly to free these
objects after they are loaded and in addition they must be set to
NULL so that the cleanup doesn't double free them.
If everything goes to plan, we load all the PEMs in settings_load,
provide these objects to the TLS APIs, and then NULL out the
pointers (TLS now owns this memory). If anything fails between
settings_load and l_tls_start we must free these objects.
A special format must be used to indicate that a PEM is embedded
inside the settings file. First, the l_settings format should be
followed for the PEM itself, e.g.
[@pem@my_ca_cert]
<CA Cert data>
This PEM can then be referenced by "embed:my_ca_cert", e.g.
EAP-TLS-CACert=embed:my_ca_cert
Any other value not starting with "embed:" will be treated as a file
path.
The IPv6 default route needs to be explicitly revoked. Unlike in IPv4,
there is no SRC address associated with the route and it will not be
removed on address removal.
The network configuration options for IPv6 are grouped under [IPv6]
and include the following:
ip= ADDRESS/PREFIX
gateway=ADDRESS
dns=ADDRESS
The placeholders for DHCPv6 are placed along the way and marked
as TODO items.
Previously, netconfig_ipv4_select_and_install was used to install
addresses on initial connection to a network and after we have roamed.
Now for the after roaming connection scenario we have
netconfig_reconfigure. Remove roaming related code from
netconfig_ipv4_select_and_install
As part of the de-coupling from station object, switch all of
the network settings inquiries to use active_settings. active_settings
are set with netconfig_configure by the owner of netconfig object
and removed with netconfig_reset once network disconnects.
Instead of relying on station state changed signal, netconfig
introduces three new API calls to configure, re-configure and
reset the network configurations. The owner of netconfig object
is responsible for initiating the re-configuration of the device
depending on its state.
As a first step to enable the usage of netconfig in ead and
prospective transition to be a part of ell, the public API for
creation and destruction of the netconfig objects has been
renamed and changed. Instead of hiding the netconfig objects inside
of netconfig module, the object is now passed back to the caller.
The internal queue of netconfig objects remains untouched, due
to limitations in ell’s implementation of rtnl. After the proper
changes are done to ell, netconfig_list is expected to be removed
from netconfig module.
A NEW_WIPHY event may not always contain all the information about a
given phy, but GET_WIPHY will. In order to get everything we must
mimic the behavior done during initalization and dump both wiphy
and interfaces when a NEW_WIPHY comes in.
Now, any NEW_WIPHY event will initialize a wiphy, but then do a
GET_WIPHY/GET_INTERFACE to obtain all the information. Because of
this we can ignore any NEW_INTERFACE notifications since we are
dumping the interface anyways.
Once some kernel changes get merged we wont need to do this anymore
so long as the 'full' NEW_WIPHY feature is supported.
If the AP sent us the plain passphrase we can now store that rather
than generating the PSK. This will allow WPA3 to work properly when
WPA3 + WSC is implemented.
This lets other modules (like WSC) to set a plain text passphrase
as opposed to only allowing a PSK to be set. network_get_psk was
also updated to generate a PSK on-the-fly if required. Since WPA3
requires the raw passphrase to work, it makes sense to just store
the passphrase if we have it.
If neighbor reports are unavailable, or the report yielded no
results we can quickly scan for only known frequencies. This
changes the original behavior where we would do a full scan
in this case.
This password key was deprecated in favor of the common EAP-Password
key. Its been about a year so we are now removing support entirely
for EAP-PWD-Password.
Gets a newly created scan_freq_set containing the most recent
frequencies for the network. The currently connected BSS frequency
(passed as a parameters) will not be included in the set.
Since the UUID was being generated purely on the file path, it
would never change for a given network (unless the SSID/name changed).
In the future we would like to use this unique UUID to generate a
MAC per-SSID, and if that network is forgotten we also want the UUID
to change next time the network is connected to.
Rather than only using the file path, the mtime can also be fed into
the UUID generation. Since the mtime would be changed after forgetting
and re-adding a known network we will get a new UUID.
Now, whenever a known network is removed, we lookup the UUID we have
in network_info and remove that entry in the settings file and
sync the frequency file.
The UUID was being generated every time we synced which is wasteful.
Instead we can track the UUID inside network_info and only generate
it once when needed.
Two new network_info APIs were added:
network_info_set_uuid
network_info_get_uuid
The setter is used when the frequency file is loaded. If a valid UUID
is found in the frequency file this UUID is set and used.
network_info_get_uuid will not just get the UUID, but actually generate
it if one has not been set yet. This will allow other modules to
get/generate the UUID if one has no been loaded from the frequency
file.
The QoS Map can come in either as a management frame or via the
Associate Response. In either case this IE simply needs to be
forwarded back to the kernel.
The extended capability bits were not being set properly inside
wiphy. Since we build the IE after the wiphy dump the first 2
bytes are the IE type and length. The way we were setting the bits
did not take this into account and were actually setting the
completely wrong bits.
The known frequency file was being loaded at the end of the known
networks initialization routine. This allowed all known networks
to be properly loaded, but since hotspot depends on known networks,
its initalization would be run afterwards meaning the frequency
loading would not have been finding any hotspot networks.
To fix this a new module was added inside known networks which
depends on hotspot. This means that first known networks will
initialize, then hotspot, then the frequency file would be loaded.
The current format for the .known_networks.freq file had a hidden
limitation of not being able to handle SSID's with some special
characters. Since the provisioning file path was used as the
group name the filename was limited to only characters supported
by l_settings groups, which conflicted with allowable SSID
characters.
Instead we can generate a unique UUID for each network and use
this as the group. For this particular case the group does not
really matter, so long as its unique. But we can utilize this unique
UUID for other purposes, including using it as a seed for changing
the MAC address per-connection in the future.
The .known_networks.freq file will now have the following format:
[<UUID>]
name=/path/to/provisioning/file
list= XXXX YYYY ZZZZ
The existing frequency syncing was done when IWD closes. Instead we
can sync as networks are connected to or promoted to known which
will keep the FS more up to date. This also allows hotspot networks
to use the known frequency file.
This API will sync the known frequencies of a network_info object
to disk. This will allow network to sync known frequencies as
known networks are added, rather that when IWD closes.
Since this will result in more frequent syncing that before, the
known_freqs settings pointer was moved globally in knownnetworks.c
as to only parse the file one time rather than on every sync.
Some of the EAP-PEAP server implementations seem to require a
cleartext ACK for the tunneled EAP-Success message similar to EAP-TLS
specification, instead of simply shutting down the tunnel like
EAP-PEAPv1 requires.
ACKing the tunneled EAP-Success seems also to work for implementations
which were relying on the tunnel close event.
create_dirs was dependent on the path ending in '/' to create the
full path. The hotspot code did not include a '/' at the end so
it was not getting created, which prevented the hotspot module
from initializing.
Station was building up the HS20 elements manually. Now we can
use this new API and let network take care of the complexity
of building network specific vendor IEs.
This op builds up the vendor IEs required for hotspot 2.0. The
version, and optionally the RC are provided in order to correctly
build the HS20 Indication Element and RC Selection element.
The HS20 module had its own getter for returning the matched roaming
consortium. Since we already have the network_info op for matching
we might as well return the matched RC rather than just a bool. This
allows the RC to be included in (Re)Association without the need for
a specific getter.
When performing a fast transition to another OPEN network the RSN
element won't be there and therefore the bss->rsne is gonna be NULL.
Fix crash by not accessing the rsne member when performing a fast
transition to an AP that doe snot advertise any RSN IE.
Crash caught with gdb:
src/station.c:station_transition_start() 186, target 34:8f:27:2f:b8:fc
Program received signal SIGSEGV, Segmentation fault.
handshake_state_set_authenticator_ie (s=0x555555626eb0, ie=0x0) at src/handshake.c:163
163 s->authenticator_ie = l_memdup(ie, ie[1] + 2u);
(gdb) bt
#0 handshake_state_set_authenticator_ie (s=0x555555626eb0, ie=0x0) at src/handshake.c:163
#1 0x0000555555561a98 in fast_transition (netdev=0x55555562fbe0, target_bss=0x55555561f4a0,
over_air=over_air@entry=true, cb=0x55555556d5b0 <station_fast_transition_cb>) at src/netdev.c:3164
#2 0x0000555555565dfd in netdev_fast_transition (netdev=<optimized out>, target_bss=<optimized out>,
cb=<optimized out>) at src/netdev.c:3232
#3 0x000055555556ccbd in station_transition_start (bss=0x55555561f4a0, station=0x555555617da0)
at src/station.c:1261
#4 station_roam_scan_notify (err=<optimized out>, bss_list=<optimized out>, userdata=0x555555617da0)
at src/station.c:1444
#5 0x0000555555579560 in scan_finished (sc=0x55555562bf80, err=err@entry=0, bss_list=0x55555561bd90,
sr=0x555555626b30, wiphy=<optimized out>) at src/scan.c:1234
#6 0x0000555555579620 in get_scan_done (user=0x555555618920) at src/scan.c:1264
#7 0x00005555555abd23 in destroy_request (data=0x55555561b000) at ell/genl.c:673
#8 0x00005555555ac129 in process_unicast (nlmsg=0x7fffffffc310, genl=0x55555560b7a0) at ell/genl.c:940
#9 received_data (io=<optimized out>, user_data=0x55555560b7a0) at ell/genl.c:1039
#10 0x00005555555a8aa3 in io_callback (fd=<optimized out>, events=1, user_data=0x55555560b840)
at ell/io.c:126
#11 0x00005555555a7ccd in l_main_iterate (timeout=<optimized out>) at ell/main.c:473
#12 0x00005555555a7d9c in l_main_run () at ell/main.c:520
#13 l_main_run () at ell/main.c:502
#14 0x00005555555a7fac in l_main_run_with_signal (callback=<optimized out>, user_data=0x0)
at ell/main.c:642
#15 0x000055555555e5b8 in main (argc=<optimized out>, argv=<optimized out>) at src/main.c:519
After wsc_store_credentials, wsc_try_credentials is called which
sets the PSK obtained via the protocol. After the known network
refactor network_settings_load was changed to depend on the
network_info->open() call. Since there is no known network for
this initial WSC connection this always fails and the PSK is not
set into the network object (and the connection is failed).
In this case if network_settings_load fails we can just create
an empty settings object to be filled later.
known_network_update was being used to both update and create known
networks as they appeared on the file system. Hotspot needs updating
capabilities so known_network_update was exposed and updated with
one major difference; it no longer can be used to create new known
networks. For creation, a new API was added (known_network_new)
which will create and add to the queue.
Since hotspot networks may require ANQP the autoconnect loop needed to
be delayed until after the ANQP results came back and the network
objects were updated. If there are hotspot networks in range ANQP will
be performed and once complete autoconnect will begin for all networks
including hotspots. If no hotspots are in range autoconnect will
proceed as it always has.
Note: Assuming hotspots are in range this will introduce some delay
in autoconnecting to any network since ANQP must come back. The full
plan is to intellegently decide when and when not to do ANQP in order
to minimize delays but since ANQP is disabled by default the behavior
introduced with this patch is acceptable.
The remove op was being called inside known_networks_remove, which only
gets called from L_DIR_WATCH events. In this case the actual provisioning
has already been removed. Calling remove() again causes the op
implementation to then try and remove the file that no longer exists.
Valgrind does not like uninitialized bytes used in a syscall. In this
case the buffer is an out buffer but since valgrind doesn't know that
it complains. Initializing to zero fixes the warning:
Syscall param socketcall.sendto(msg) points to uninitialised byte(s)
at 0x5162C4D: send (send.c:28)
by 0x457AF4: l_checksum_update (checksum.c:319)
by 0x43C03C: eap_wsc_handle_m2 (eap-wsc.c:842)
by 0x43CD33: eap_wsc_handle_request (eap-wsc.c:1048)
by 0x43A3A7: __eap_handle_request.part.0 (eap.c:266)
by 0x41A426: eapol_rx_packet.part.12 (eapol.c:2262)
by 0x41B536: __eapol_rx_packet (eapol.c:2650)
by 0x407C80: netdev_control_port_frame_event (netdev.c:3542)
by 0x407C80: netdev_unicast_notify (netdev.c:3684)
by 0x4598C5: dispatch_unicast_watches (genl.c:899)
by 0x4598C5: process_unicast (genl.c:918)
by 0x4598C5: received_data (genl.c:1039)
by 0x456452: io_callback (io.c:126)
by 0x45569D: l_main_iterate (main.c:473)
by 0x45576B: l_main_run (main.c:520)
Address 0x1ffeffe290 is on thread 1's stack
in frame #2, created by eap_wsc_handle_m2 (eap-wsc.c:797)
We were not using or taking into account the noencrypt flag obtained
from the kernel via CONTROL_PORT events. For the most part this still
worked as the kernel would never include NO_ENCRYPT flag (due to a bug).
However, this was actually incorrect and led to loss of synchronization
between the AP and STA 4-Way handshake state machines when certain
packets were lost and had to be re-transmitted.
Allow users to provide a glob string that the contents of the server
certificate's subject DN should be matched against as a primitive
protection against rogue APs using certificates purchased from
commercial CAs trusted by the client. If the network uses an AP
certificate emitted by a commerical CA and the clients are configured
to trust those CAs so that the client configurations don't have to be
updated when the AP renews its certificate, this new option can be used
to check if the CN in the AP certificate's DN matches the known domain
name. This logic assumes that the commercial CAs provide enough
assurance that only the owner of the domain can buy a certificate with
that domain in the CN field.
The format of this option is similar to apple's TLSTrustedServerNames
and wpa_supplicant's domain_match/domain_suffix_match format, the exact
syntax is documented in ell/tls.c.
Some capability bits are required by the spec to be set for
probe requests for certain features (HS20, FILS, FT). Currently
these features work as-is, but depending on the hardware we may
be in violation of the spec if we assume the correct bits are
set when we get the wiphy dump.
Just to be safe we can explicity set these capability bits.
There are also two ways the kernel exposes these capabilities.
Per-type or globally. The hardware may expose one, or both of
these capability arrays. To combat this we are now always
creating a per-type capability array for stations. If the
wiphy dump has not produced a per-type capability array we
now create one based off the global capability array. That
way we can always assume there is a capability array for a
station iftype.
This will be seen in Probe Requests. More IEs can and should
be added here depending on the support in IWD. E.g. HS20 indication,
Interworking, HT/VHT IE's etc.
In order to implement get_name/get_type we need some value for the name
of the hotspot network. For simplicity we now require a 'Name' value
be provided inside the hotspot provisioning file. Eventually this may
change (e.g. obtained via ANQP).
Rather than using timespec directly, ELL has a convenient API
to get the elapsed microseconds as a uint64_t. This can then
be used with the other l_time_ APIs for comparison.
This patch removes timespec from network_info and updates
to use l_time_* API's for sorting.
These operations will allow the hotspot module to implement
matching HESSID, Roaming Consortium, and NAI realms. This offloads
the matching details into the hotspot module.
This way resolve_remove can be called once per interface and
remove IPv4 and IPv6 addresses at once.
In addition, this allows to remove the IP addresses and DNS
servers within the same main loop cycle. This will allow iwd
to make an attempt to remove the DNS servers on shutdown of iwd.
These two API's have been added to allow hotspot to add its
own networks to the known network list. This will allow any
added networks to behave exactly like they do now, including
all the dbus and watchlist functionality.
The known network APIs all revolved around the ssid/security matching
to do any operations on the provisioning file. In the near future
hotspot provisioning files (managed by hotspot.c) will be incorporated
into the known network list. Since these hotspot files do not use the
ssid as the file name hotspot.c will need other ways of matching.
This patch adds network_info_ops to the network object. This ops
structure will hold function pointers which operate on network_info
rather than ssid/security. This will allow hotspot and known networks
to both register their own operation routines.
For now open, touch, sync, remove, free, and get_path were added.
Wrappers were added for accessing these operations outside of
knownnetworks.c.
Isolate the known_frequency queue management to a function and place
that function in knownnetworks.c where it now belongs. Since we no
longer have network_info objects for unknown networks, only frequencies
for known networks are tracked
networks queue was intended to share basic network information between
multiple adapters running simultaneously. The network_info object was
also serving double duty to carry known network information. This made
things overly complicated and really didn't result in much savings.
This setup also made managing hotspot networks challenging as we would
have ended up with multiple network_info objects for each known hotspot
network.
So get rid of the networks queue and the is_known bit from the
network_info structure.
network_find_rank_index was used to find the offset of the selected
network_info among known networks so as to compute a modifier based on
the rankmod table. Instead of using known_networks_foreach for this,
moove it to knownnetworks.c where it can be coded and optimized
separately.
For now provide a simple for loop implementation.
Previously, the option PrivateDevices=true disabled access to
/dev/rfkill, which lead to:
'iwctl adapter phy0 set-property Powered {off|on}'
to fail.
This patch explicitly allows access to /dev/rfkill
src/rtnlutil.c: In function ‘rtnl_route_add’:
./ell/util.h:248:2: error: ‘rtmmsg’ may be used uninitialized in
this function [-Werror=maybe-uninitialized]
Instead of using a flag ipv4_static, just store the value of the rtm
protocol directly inside netconfig object. This allows us to simplify
the logic quite significantly and avoid repeating the conditional
expression needlessly
The routes are installed as a result of a successful installation
of the IP addresses. The gateway is fetched with netconfig_ipv4_get_gateway
helper function according to the origin of the installed IP address.
The route priority offset can be set in main.conf. The default value
of 300 is used if the offset isn’t set.
The API allows to add connected and gateway routes to the main
routing table.
rtnl_route_ipv4_add_gateway() is equivalent to the following
example 'ip route' command:
ip route add default via 10.0.0.1 dev wlan0 proto dhcp src 10.0.0.2 metric 339
rtnl_route_ipv4_add_connected() is equivalent to the following
example 'ip route' command:
sudo ip route add 10.0.0.0/24 dev wlan0 proto dhcp src 10.0.0.2 scope link
The 'ip route' output from the above commands looks as follows:
rtnl_route_ipv4_add_connected():
10.0.0.0/24 dev wlan0 proto dhcp scope link src 10.0.0.2
rtnl_route_ipv4_add_gateway():
default via 10.0.0.1 dev wlan0 proto dhcp src 10.0.0.2 metric 339
The DNS addresses are installed as a result of a successful
installation of the IP addresses. The DNS lists are fetched
with netconfig_ipv4_get_dns helper function according to the
origin of the installed IP address.
iwd reconfigures the wireless interfaces with respective
connection events. Each supported network protocol is
reconfigured. The address for each protocol is
selected as static or dynamic based on availability.
netconfig_ipv4_get_ifaddr helper function allows to fetch IPv4
addresses from static or dynamic sources. The origin of the addresses
is noted in 'ipv4_is_static' flag.
For (Re)Association the HS20 indication element was passed exactly as
it was found in the scan results. The spec defines what bits can be
set and what cannot when this IE is used in (Re)Association. Instead
of assuming the AP's IE conforms to the spec, we now parse the IE and
re-build it for use with (Re)Association.
Since the full IE is no longer used, it was removed from scan_bss, and
replaced with a bit for HS20 support (hs20_capable). This member is
now used the same as hs20_ie was.
The version parsed during scan results is now used when building the
(Re)Association IE.
The parser fully parses the IE and returns the version, Domain ID,
and PPS MO ID. This is meant to be used with an IE in scan results.
The builder only takes the version number, and assumes DGAF disabled,
and no Domain ID or PPS MO ID.
Previously, iwd used to throw net.connman.iwd.Busy when connection
attempt was made while connected. The new behavior allows iwd to
seamlessly disconnect from the connected network and attempt a new
connection.
Since NAI realms, Roaming Consortium and HESSID are defined in 802.11,
they are not a guarentee that the network is Hotspot 2.0. The indication
element in addition to these IE's gives a better idea of Hotspot 2.0
support. Now, when a BSS is added this is_hs20 boolean will get set to
true if the HS20 IE was found in the BSS.
Now, if is_hs20 is set AND one of NAI realms, roaming consortium, or
HESSID is set we know this is a hotspot 2.0 network.
It is possible for a zero-length anti-clogging token payload to cause
IWD to abort. If the length passed into sae_process_anti_clogging was
1, l_memdup would be called with a size of -1. This will cause malloc
to abort.
Fix this by checking for a minimum packet length and dropping the
packet if the length is too small.
The HS20 indication element should always be included during
(Re)Association per the spec. This removes the need for a
dedicated boolean, and now the hs20_ie can be used instead.
The hotspot spec specifically mentions the roaming consortium OI be
3 or 5 bytes long. This requirement also prevents potential buffer
overflows if the user were to configure a long roaming consortium OI.
If the scan was triggered and later aborted, make sure to reset the
triggered value when the CMD_NEW_SCAN_RESULTS event comes in.
src/station.c:station_enter_state() Old State: disconnected, new state: connecting
src/scan.c:scan_notify() Scan notification 33
src/station.c:station_netdev_event() Associating
src/scan.c:scan_notify() Scan notification 34
Aborting (signal 11) [/home/denkenz/iwd-master/src/iwd]
++++++++ backtrace ++++++++
#0 0x7efd4d6a2ef0 in /lib64/libc.so.6
#1 0x42b20d in scan_notify() at src/scan.c:1383
In the same fashion as the WSC WFA OUI, ie.[ch] will now expose the
other vendor OUIs to avoid duplication across multiple files in IWD
as well as used in iwmon.
P2P probe requests are to be sent at min 6.0 Mb/s using OFDM,
specifically the 802.11b rates are prohibited (section 2.4.1 in Wi-Fi
P2p Technical Spec v1.7), some of which use CCK modulation. This is
already the default for 5G but for 2.4G the drivers generally do this
if we set the NL80211_ATTR_TX_NO_CCK_RATE flags with
NL80211_CMD_TRIGGER_SCAN.
The length check was incorrectly assuming that PPS MO ID or
ANQP Domain ID would be present in the IE. Both these are optional
and without then the minimum length is 5 bytes, not 7.
Per the hotspot 2.0 spec, if a matching roaming consortium OI is
found it should be added to the (Re)Association request. vendor_ies
can now be provided to netdev_connect, which get appended to the IE
attribute.
This API will attempt to find a matching roaming consortium OI
if present in the config file. A single matching OI is returned
or NULL if one was not found.
Hotspot 2.0 network providers allow 'roaming' between a users home
network and other providers networks, assuming they are part of the
same roaming consortium. The roaming consortium is advertised as an
IE in beacon/probe frames.
In terms of the hotspot config files this is similar to HESSID, where
if the AP advertises the roaming consortium IE, and the config file
matches we do not need to do ANQP in order to connect.
This is duplicated when the first scan_bss is added to a network
object that contains the IE. Any future BSS's added will not re-add
the IE. Its assumed that all BSS's under a network will contain the
same roaming consortium OIs.
Parses up to 3 (the max) roaming consortium OIs out of the roaming
consortium IE. If more OIs are available via ANQP the 'num_anqp_out'
value will be set to indicate how many more OIs are available.
Builds according to the hotspot 2.0 spec using the vendor specific
IE.
Declare structures to hold the parsed contents of the P2P IEs and WSC
IEs in P2P-related frames and add functions to free memory used by
those structures.
Define structs and types for most P2P attributes and p2p_parse_attrs
similar to wsc_parse_attrs -- a generic parser for attributes in a P2P
IE payload. This parser may write into the provided buffer even on
error but it's private to p2putil.c. The local callers will take care
of keeping the user-provided buffers untouched on error.
Add a utility for building the simplified WSC IEs used in P2P action
frames and public action frames. Only three types of WSC attributes are
mandatory in those frames (but different subsets are needed by different
frame types) so add a single utility for building those IEs. We may
need to add some more optional attributes to those IEs later.
The ifindex is used to index the netdevs in the system (wlan, ethernet,
etc.) but we can also do wifi scanning on interfaces that have no
corresponding netdev object, like the P2P-device virtual interfaces.
Use the wdev id's to reference interfaces, the nl80211 api doesn't care
whether we use a NL80211_ATTR_IFINDEX or NL80211_ATTR_WDEV. Only
wireless interfaces have a wdev id.
Save the actual cmd_id returned from l_genl_family_dump and zero it in
the get_scan_done. There's no need to zero it in scan_cancel because
get_scan_done gets called automatically.
Store the scan_context pointer in scan_results directly instead of
storing the ifindex. We now cancel ongoing GET_SCAN commands when the
scan_context is being freed so there's no point going through the extra
step of looking up the scan_context by ifindex inside the command
callback to guard against non-existent scan_contexts.
method.ops is NULL, which causes method.ops->exit to crash. This
adds a check that method.ops is not NULL before dereferencing.
Fixes:
Aborting (signal 11) [/home/jprestwo/iwd/src/iwd]
++++++++ backtrace ++++++++
0 0x7f016b59cf20 in /lib/x86_64-linux-gnu/libc.so.6
1 0x432057 in resolve_exit() at /home/jprestwo/iwd/src/resolve.c:295
2 0x403b61 in iwd_modules_exit() at /home/jprestwo/iwd/src/main.c:195
3 0x7f016b57fb97 in /lib/x86_64-linux-gnu/libc.so.6
+++++++++++++++++++++++++++
The original idea was to allow the provisioning file to include HESSID
without the NAIRealmNames. Configuring this way would allow for ANQP
to be skipped completely, assuming the AP advertises its HESSID.
The way the code was written still required NAIRealmNames to be
provided in the provisioning file.
The framework enables the service specific implementations
to provide its own variations for the DNS installation tasks.
The selection of the address resolution service can be done
through dns_resolve_method setting.
The module is responsible for the configuration of the address
resolution services. It will consist of the multiple service
specific plugins such as: systemd-resolved plugin, dnsmasq
plugin, etc.
If supported by the driver, we can create an interface directly with a
random MAC if configured to do so. If the driver does not have this
capability, then tell netdev to perform the necessary logic as part of
the interface initialization procedure.
#0 0x7f5e25e71930 in /lib64/libc.so.6
#1 0x446faa in hs20_config_free() at src/hotspot.c:63
#2 0x469542 in l_queue_clear() at ell/queue.c:109
#3 0x4694e7 in l_queue_destroy() at ell/queue.c:83
#4 0x4475c1 in hotspot_exit() at src/hotspot.c:273
#5 0x403170 in iwd_modules_exit() at src/main.c:195
#6 0x404085 in main() at src/main.c:531
#7 0x7f5e25e5cbde in /lib64/libc.so.6
Regulatory domain management is now completely handled by the kernel, so
iwd doesn't really need to query or be aware of changes to this. This
may change in the future, but for now this code has not been used and
can be safely gotten rid of.
After a scan, station can now pause future scans and start ANQP requests
to discover Hotspot's NAI realm. This lets us check if the AP's NAI realm
matches any stored hotspot configuration files. If so we can connect to
this network. If the network provides an HESSID and a matching one is
found in a hotspot provisioning file we can skip ANQP and directly connect
as this is expected to be our 'home network'
The actual ANQP request was handled by netdev, but in the case of P2P
their may be no netdev. For this reason all functionality needed for
an ANQP request has been moved into anqp.c. There are still a few netdev
references, which need to be removed when P2P is introduced. Leaving them
in for now as its still going to work as a first pass implementation
The initial ANQP parser design did not work well with how the hotspot
implementation was turning out. For one, much care was taken into parsing
the EAP credentials which are not really required. The assumption is
that any hotspot network will already be provisioned, so checking that
the EAP parameters match is a bit overkill. Instead only the NAI Realms
will be checked. This greatly simplifies the NAI realm parser, as now it
can just return a string list of realms instead of the full EAP
credential info.
This module will be in charge of managing Hotspot provisioning files
stored under the .hotspot/ directory. This includes a dir watch to
handle file changes/removal as well as an API to match a network
object to a hotspot provisioning file.
Hotspot networks are supposed to include an HESSID in the scan
results. This is more or less an identifier for the overall
network. In addition, the NAI Realms can be obtained via ANQP
and should be the same for each BSS. Since both HESSID and NAI
realms should be the same for a given network in range we can
store these values in the network object itself. This also allows
us to easily find hotspot configuration files by looking at
the HESSID/NAI Realms directly in the network object as opposed
to individual scan_bss's.
In order to do ANQP efficiently IWD needs the ability to suspend scanning
temporarily. This is because both scanning and ANQP go offchannel and must
remain off channel for some amount of time. This cannot be done
simultaneously and if e.g. ANQP is requested after a scan is already
pending, the kernel will wait till that scan finishes before sending out
the frame.
