With the introduction of affinities the CQM threshold can be toggled
by a DBus call. There was no check if there was already a pending
call which would cause the command ID to be overwritten and lose any
potential to cancel it, e.g. if netdev went down.
Some drivers fail to set a CQM threshold and report not supported.
Its unclear exactly why but if this happens roaming is effectively
broken.
To work around this enable RSSI polling if -ENOTSUP is returned.
The polling callback has been changed to emit the HIGH/LOW signal
threshold events instead of just the RSSI level index, just as if
a CQM event came from the kernel.
When the affinity is set to the current BSS lower the roaming
threshold to loosly lock IWD to the current BSS. The lower
threshold is automatically removed upon roaming/disconnection
since the affinity array is also cleared out.
This property will hold an array of object paths for
BasicServiceSet (BSS) objects. For the purpose of this patch
only the setter/getter and client watch is implemented. The
purpose of this array is to guide or loosely lock IWD to certain
BSS's provided that some external client has more information
about the environment than what IWD takes into account for its
roaming decisions.
For the time being, the array is limited to only the connected
BSS path, and any roams or disconnects will clear the array.
The intended use case for this is if the device is stationary
an external client could reduce the likelihood of roaming by
setting the affinity to the current BSS.
This documents new DBus property that expose a bit more control to
how IWD roams.
Setting the affinity on the connected BSS effectively "locks" IWD to
that BSS (except at critical RSSI levels, explained below). This can
be useful for clients that have access to more information about the
environment than IWD. For example, if a client is stationary there
is likely no point in trying to roam until it has moved elsewhere.
A new main.conf option would also be added:
[General].CriticalRoamThreshold
This would be the new roam threshold set if the currently connected
BSS is in the Affinities list. If the RSSI continues to drop below
this level IWD will still attempt to roam.
A user reported a crash which was due to the roam trigger timeout
being overwritten, followed by a disconnect. Post-disconnect the
timer would fire and result in a crash. Its not clear exactly where
the overwrite was happening but upon code inspection it could
happen in the following scenario:
1. Beacon loss event, start roam timeout
2. Signal low event, no check if timeout is running and the timeout
gets overwritten.
The reported crash actually didn't appear to be from the above
scenario but something else, so this logic is being hardened and
improved
Now if a roam timeout already exists and trying to be rearmed IWD
will check the time remaining on the current timer and either keep
the active timer or reschedule it to the lesser of the two values
(current or new rearm time). This will avoid cases such as a long
roam timer being active (e.g. 60 seconds) followed by a beacon or
packet loss event which should trigger a more agressive roam
schedule.
This adds a secondary set of signal thresholds. The purpose of these
are to provide more flexibility in how IWD roams. The critical
threshold is intended to be temporary and is automatically reset
upon any connection changes: disconnects, roams, or new connections.
This prepares for the ability to toggle between two signal
thresholds in netdev. Since each netdev may not need/want the
same threshold store it in the netdev object rather than globally.
Since IWD enrollees can send unicast frames, a PKEX configurator could
still run without multicast support. Using this combination basically
allows any driver to utilize DPP/PKEX assuming the MAC address can
be communicated using some out of band mechanism.
The DPP spec allows for obtaining frequency and MAC addresses up
to the implementation. IWD already takes advantage of this by
first scanning for nearby APs and using only those frequencies.
For further optimization an enrollee may be able to determine the
configurators frequency and MAC ahead of time which would make
finding the configurator much faster.
This will help to get rid of magic number use throughout the project.
The definitions should be limited to global magic numbers that are used
throughout the project, for example SSID length, MAC address length,
etc.
Due to an unnoticed bug after adding the BasicServiceSet object into
network, it became clear that since station already owns the scan_bss
objects it makes sense for it to manage the associated DBus objects
as well. This way network doesn't have to jump through hoops to
determine if the scan_bss object was remove, added, or updated. It
can just manage its list as it did prior.
From the station side this makes things very easy. When scan results
come in we either update or add a new DBus object. And any time a
scan_bss is freed we remove the DBus object.
To reduce code duplication and prepare for moving the BSS interface
to station, add a new API so station can create a BSS path without
a network object directly.
src/eapol.c:1041:9: error: ‘buf’ may be used uninitialized [-Werror=maybe-uninitialized]
1041 | l_put_be16(0, &frame->header.packet_len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This warning is bogus since the buffer is initialized through use of
eapol_frame members. EAPoL-Start is a very simple frame.
This was seemingly trivial at face value but doing so ended up
pointing out a bug with how group_retry is set when forcing
the default group. Since group_retry is initialized to -1 the
increment in the force_default_group block results in it being
set to zero, which is actually group 20, not 19. This did not
matter for hunt and peck, but H2E actually uses the retry value
to index its pre-generated points which then breaks SAE if
forcing the default group with H2E.
To handle H2E and force_default_group, the group selection
logic will always begin iterating the group array regardless of
SAE type.
The property itself is an array of paths, but this is difficult
to fit nicely within a terminal. Instead just display the count
of BSS's. Displaying a detailed list of BSS's will be done via
a separate command.
There are certain cases where we may not want to display the entire
header for a given set of properties. For example displaying a list
of proxy interfaces. Add finer control by separating out the header
and the prop/value display into two functions.
