We should never reach a point where NEW_SCAN_RESULTS or SCAN_ABORTED are
received before a corresponding TRIGGER_SCAN is received. Even if this
does happen, there's no harm from processing the commands anyway.
This makes it a little easier to book-keep the started variable. Since
scan_request already has a 'passive' bit-field, there should be no
storage penalty.
If scan_cancel is called on a scan_request that is 'finished' but with
the GET_SCAN command still in flight, it will trigger a crash as
follows:
Received Deauthentication event, reason: 2, from_ap: true
src/station.c:station_disconnect_event() 11
src/station.c:station_disassociated() 11
src/station.c:station_reset_connection_state() 11
src/station.c:station_roam_state_clear() 11
src/scan.c:scan_cancel() Trying to cancel scan id 6 for wdev 200000002
src/scan.c:scan_cancel() Scan is at the top of the queue, but not triggered
src/scan.c:get_scan_done() get_scan_done
Aborting (signal 11) [/home/denkenz/iwd-master/src/iwd]
++++++++ backtrace ++++++++
#0 0x7f9871aef3f0 in /lib64/libc.so.6
#1 0x41f470 in station_roam_scan_notify() at /home/denkenz/iwd-master/src/station.c:2285
#2 0x43936a in scan_finished() at /home/denkenz/iwd-master/src/scan.c:1709
#3 0x439495 in get_scan_done() at /home/denkenz/iwd-master/src/scan.c:1739
#4 0x4bdef5 in destroy_request() at /home/denkenz/iwd-master/ell/genl.c:676
#5 0x4c070b in l_genl_family_cancel() at /home/denkenz/iwd-master/ell/genl.c:1960
#6 0x437069 in scan_cancel() at /home/denkenz/iwd-master/src/scan.c:842
#7 0x41dc2e in station_roam_state_clear() at /home/denkenz/iwd-master/src/station.c:1594
#8 0x41dd2b in station_reset_connection_state() at /home/denkenz/iwd-master/src/station.c:1619
#9 0x41dea4 in station_disassociated() at /home/denkenz/iwd-master/src/station.c:1644
The happens because get_scan_done callback is still called as a result of
l_genl_cancel. Add a re-entrancy guard in the form of 'canceled'
variable in struct scan_request. If set, get_scan_done will skip invoking
scan_finished.
It isn't clear what 'l_queue_peek_head() == results->sr' check was trying
to accomplish. If GET_SCAN dump was scheduled, then it should be
reported. Drop it.
results->sr is set to NULL for 'opportunistic' scans which were
triggered externally. See scan_notify() for details. However,
get_scan_done would only invoke scan_finished (and thus the periodic
scan callback sc->sp.callback) only if the scan queue was empty. It
should do so in all cases.
The point type was being hard coded to 0x3 (BIT1) which may have resulted
in the peer subtracting Y from P when reading in the point (depending on
if Y was odd or not).
Instead set the compressed type to whatever avoids the subtraction which
both saves IWD from needing to do it, as well as the peer.
The intent of this check is to make sure that at least 2 bytes are
available for reading. However, the unintended consequence is that tags
with a zero length at the end of input would be rejected.
While here, rework the check to be more resistant to potential
overflow conditions.
First disconnect wpa_supplicant to make sure it wont miss frames if
it decides to connect. Also alter the order of things for the
configurator test so autoconnect doesn't start until after hostapd
is up (avoids additional scanning and delays)
The DPP spec says nothing about how to handle re-transmits but it
was found in testing this can happen relatively easily for a few
reasons.
If the configurator requests a channel switch but does not get onto
the new channel quick enough the enrollee may have already sent the
authenticate response and it was missed. Also by nature of how the
kernel goes offchannel there are moments in time between ROC when
the card is idle and not receiving any frames.
Only frames where there was no ACK will be retransmitted. If the
peer received the frame and dropped it resending the same frame wont
do any good.
Now the result is sent immediately. Prior a connect attempt or
scan could have started, potentially losing this frame. In addition
the offchannel operation is cancelled after sending the result
which will allow the subsequent connect or scan to happen much
faster since it doesn't have to wait for ROC to expire.
The previous (incorrect) else was removed since it ended up
printing in most cases since the if clause returned. This should
have been an else if conditional from the start and only print if the
station device was not found.
IWD may be in the middle of some long operation, e.g. scanning.
If the URI is returned before IWD is ready, a configurator could
start sending frames and IWD either wont receive them, or will
be unable to respond quickly.
Controlling wpa_supplicant/hostapd from a text based interface is
problematic in that there is no way of knowing if an event corresponds
to a request. In certain cases if wpa_s/hostapd is sending out multiple
events and we make a request, a random event may come back after the
request, but before the actual result.
To fix this, at least for this specific case, we can continue to read
from the socket until the result is numeric.
The offchannel priority was also changed to zero, which matches the
priority of frames. Currently there should be no interaction between
offchannel and connect (previous offchannel priority).
Periodic scans were handled specially where they were only
started if no other requests were pending in the scan queue.
This is fine, and what we want, but this can actually be
handled automatically by nature of the wiphy work queue rather
than needing to check the request queue explicitly.
Instead we can insert periodic scans at a lower priority than
other scans. This puts them at the end of the work queue, as
well as allows future requests to jump ahead if a periodic scan
has not yet started.
Eventually, once all pending scans are done, the peridoic scan
may begin. This is no different than the preivous behavior and
avoids the need for any special checks once scan requests
complete.
One check was added to address the problem of the periodic scan
timer firing before the scan could even start. Currently this
happened to be handled fine in scan_periodic_queue, as it checks
the queue length. Since this check was removed we must see check
for this condition inside scan_periodic_timeout.
This adds a priority argument to scan_common rather than hard
coding it when inserting the work item and uses the newly
defined wiphy priority for scanning.
Work priority was never explicitly defined anywhere, and a module
using wiphy_radio_work APIs needed to ensure it was not inserting
at a priority that would interfere with other work.
Now all the types of work have been defined with their own priority
and future priorities can easily be added before, after, or in
between existing priorities.
- Mostly problems with whitespace:
- Use of spaces instead of tabs
- Stray spaces before closing ')
- Missing spaces
- Missing 'void' from function declarations & definitions that
take no arguments.
- Wrong indentation level
