3
0
mirror of https://git.kernel.org/pub/scm/network/wireless/iwd.git synced 2024-12-29 13:12:50 +01:00
iwd/doc/main.conf
2019-05-02 10:47:45 -05:00

88 lines
3.3 KiB
Plaintext

# Note: The lines starting with # are ignored. To enable any of the
# configuration options below, remove # from the beginning of a respective line.
[EAP]
mtu=1400
[EAPoL]
max_4way_handshake_time=5
[General]
#
# Enable/Disable sending EAPoL packets over NL80211. Enabled by default if
# kernel support is available. Doing so sends all EAPoL traffic over directly
# to the supplicant process (iwd) instead of putting these on the Ethernet
# device. Since only the supplicant can usually make sense / decrypt these
# packets, enabling this option can save some CPU cycles on your system and
# avoids certain long-standing race conditions.
#
# Note, iwmon cannot currently spy on unicast packets sent over netlink, so
# if you need to capture EAPoL packets (e.g. for debugging) then this option
# should be set to False.
ControlPortOverNL80211=True
#
# Set the threshold RSSI for roaming
roam_rssi_threshold=-70
#
# Do not allow iwd to destroy / recreate wireless interfaces at startup,
# including default interfaces. Enable this behavior if your wireless card
# driver is buggy or does not allow such an operation, or if you do not want
# iwd to manage netdevs for another reason. For most users with an upstream
# driver it should be safe to omit/disable this setting.
# use_default_interface=true
[Scan]
#
# Disable periodic scan. Setting this option to 'true' will prevent iwd from
# issuing the periodic scans for the available networks while disconnected.
# The behavior of the user-initiated scans isn't affected.
# The periodic scan is enabled by default.
#disable_periodic_scan=true
#
#
# Disable roaming scan. Setting this option to 'true' will prevent iwd from
# issuing the roaming scans for the available networks while connected.
# The behavior of the user-initiated scans isn't affected.
# The roaming scan is enabled by default.
#disable_roaming_scan=true
#
#
# Disable MAC address randomization. Setting this option to 'true' will prevent
# the capable network adapters from randomizing MAC addresses during the active
# scans for networks, thus decreasing user privacy.
# The MAC address randomization is enabled by default.
#disable_mac_address_randomization=true
#
[Blacklist]
#
# Configure BSS blacklist time/multipler/max. If a connection to a BSS fails for
# whatever reason we can avoid connecting to this BSS in the future by
# blacklisting it. These three options configure how long a BSS is blacklisted
# for.
#
# bss_blacklist_time - The initial timeout for a blacklisted BSS in
# seconds.
# bss_blacklist_multiplier - What bss_blacklist_time is multiplied by after
# future unsuccessful connection attempts in
# seconds.
# bss_blacklist_max_time - The maximum time a BSS can be blacklisted for in
# seconds.
#
#bss_blacklist_time=60
#bss_blacklist_multiplier=30
#bss_blacklist_max_time=86400
[Rank]
#
# Manually specify a 5G ranking factor. 5G networks are already preferred but
# only in terms of calculated data rate, which is RSSI dependent. This means it
# is still possible for IWD to prefer a 2.4GHz AP in the right conditions.
# This ranking provides a way to further weight the ranking towards 5G if
# required. Also, a lower 5G factor could be used to weight 2.4GHz if that is
# desired.
#
#rank_5g_factor=1.0