mirror of
https://git.kernel.org/pub/scm/network/wireless/iwd.git
synced 2024-12-22 04:32:37 +01:00
273f0d358b
The way IWD does ANQP depends on a recent kernel patch so its best if we have ANQP disabled by default. In addition it has been found some drivers do public action frames very badly, resulting in freezes or crashes. If users are feeling brave, or are confident they're system can handle ANQP properly they can enable this. Enabling this option is required for Hotspot 2.0 support
108 lines
4.0 KiB
Plaintext
108 lines
4.0 KiB
Plaintext
# Note: The lines starting with # are ignored. To enable any of the
|
|
# configuration options below, remove # from the beginning of a respective line.
|
|
|
|
[EAP]
|
|
mtu=1400
|
|
|
|
[EAPoL]
|
|
max_4way_handshake_time=5
|
|
|
|
[General]
|
|
#
|
|
# Enable/Disable sending EAPoL packets over NL80211. Enabled by default if
|
|
# kernel support is available. Doing so sends all EAPoL traffic over directly
|
|
# to the supplicant process (iwd) instead of putting these on the Ethernet
|
|
# device. Since only the supplicant can usually make sense / decrypt these
|
|
# packets, enabling this option can save some CPU cycles on your system and
|
|
# avoids certain long-standing race conditions.
|
|
#
|
|
# Note, iwmon cannot currently spy on unicast packets sent over netlink, so
|
|
# if you need to capture EAPoL packets (e.g. for debugging) then this option
|
|
# should be set to False.
|
|
ControlPortOverNL80211=True
|
|
#
|
|
# Set the threshold RSSI for roaming
|
|
roam_rssi_threshold=-70
|
|
#
|
|
# Do not allow iwd to destroy / recreate wireless interfaces at startup,
|
|
# including default interfaces. Enable this behavior if your wireless card
|
|
# driver is buggy or does not allow such an operation, or if you do not want
|
|
# iwd to manage netdevs for another reason. For most users with an upstream
|
|
# driver it should be safe to omit/disable this setting.
|
|
# use_default_interface=true
|
|
|
|
#
|
|
# Explicitly enforce/disable management frame protection
|
|
#
|
|
# 0 - Disable management frame protection
|
|
# 1 - Set management frame protection capable
|
|
# 2 - Management frame protection required
|
|
#
|
|
# ManagementFrameProtection=1
|
|
|
|
#
|
|
# Enable/disable ANQP queries. The way IWD does ANQP queries is dependent on
|
|
# a recent kernel patch. If your kernel does not have this functionality this
|
|
# should be disabled (default). Some drivers also do a terrible job of sending
|
|
# public action frames (freezing or crashes) which is another reason why this
|
|
# has been turned off by default. All aside, if you want to connect to Hotspot
|
|
# 2.0 networks ANQP is most likely going to be required (you may be able to
|
|
# pre-provision to avoid ANQP).
|
|
#
|
|
# disable_anqp=true
|
|
|
|
[Scan]
|
|
#
|
|
# Disable periodic scan. Setting this option to 'true' will prevent iwd from
|
|
# issuing the periodic scans for the available networks while disconnected.
|
|
# The behavior of the user-initiated scans isn't affected.
|
|
# The periodic scan is enabled by default.
|
|
#disable_periodic_scan=true
|
|
#
|
|
|
|
#
|
|
# Disable roaming scan. Setting this option to 'true' will prevent iwd from
|
|
# issuing the roaming scans for the available networks while connected.
|
|
# The behavior of the user-initiated scans isn't affected.
|
|
# The roaming scan is enabled by default.
|
|
#disable_roaming_scan=true
|
|
#
|
|
|
|
#
|
|
# Disable MAC address randomization. Setting this option to 'true' will prevent
|
|
# the capable network adapters from randomizing MAC addresses during the active
|
|
# scans for networks, thus decreasing user privacy.
|
|
# The MAC address randomization is enabled by default.
|
|
#disable_mac_address_randomization=true
|
|
#
|
|
|
|
[Blacklist]
|
|
#
|
|
# Configure BSS blacklist time/multipler/max. If a connection to a BSS fails for
|
|
# whatever reason we can avoid connecting to this BSS in the future by
|
|
# blacklisting it. These three options configure how long a BSS is blacklisted
|
|
# for.
|
|
#
|
|
# bss_blacklist_time - The initial timeout for a blacklisted BSS in
|
|
# seconds.
|
|
# bss_blacklist_multiplier - What bss_blacklist_time is multiplied by after
|
|
# future unsuccessful connection attempts in
|
|
# seconds.
|
|
# bss_blacklist_max_time - The maximum time a BSS can be blacklisted for in
|
|
# seconds.
|
|
#
|
|
#bss_blacklist_time=60
|
|
#bss_blacklist_multiplier=30
|
|
#bss_blacklist_max_time=86400
|
|
|
|
[Rank]
|
|
#
|
|
# Manually specify a 5G ranking factor. 5G networks are already preferred but
|
|
# only in terms of calculated data rate, which is RSSI dependent. This means it
|
|
# is still possible for IWD to prefer a 2.4GHz AP in the right conditions.
|
|
# This ranking provides a way to further weight the ranking towards 5G if
|
|
# required. Also, a lower 5G factor could be used to weight 2.4GHz if that is
|
|
# desired.
|
|
#
|
|
#rank_5g_factor=1.0
|