mirror of
https://git.kernel.org/pub/scm/network/wireless/iwd.git
synced 2024-12-22 04:32:37 +01:00
88 lines
3.3 KiB
Plaintext
88 lines
3.3 KiB
Plaintext
# Note: The lines starting with # are ignored. To enable any of the
|
|
# configuration options below, remove # from the beginning of a respective line.
|
|
|
|
[EAP]
|
|
mtu=1400
|
|
|
|
[EAPoL]
|
|
max_4way_handshake_time=5
|
|
|
|
[General]
|
|
#
|
|
# Enable/Disable sending EAPoL packets over NL80211. Enabled by default if
|
|
# kernel support is available. Doing so sends all EAPoL traffic over directly
|
|
# to the supplicant process (iwd) instead of putting these on the Ethernet
|
|
# device. Since only the supplicant can usually make sense / decrypt these
|
|
# packets, enabling this option can save some CPU cycles on your system and
|
|
# avoids certain long-standing race conditions.
|
|
#
|
|
# Note, iwmon cannot currently spy on unicast packets sent over netlink, so
|
|
# if you need to capture EAPoL packets (e.g. for debugging) then this option
|
|
# should be set to False.
|
|
ControlPortOverNL80211=True
|
|
#
|
|
# Set the threshold RSSI for roaming
|
|
roam_rssi_threshold=-70
|
|
#
|
|
# Do not allow iwd to destroy / recreate wireless interfaces at startup,
|
|
# including default interfaces. Enable this behavior if your wireless card
|
|
# driver is buggy or does not allow such an operation, or if you do not want
|
|
# iwd to manage netdevs for another reason. For most users with an upstream
|
|
# driver it should be safe to omit/disable this setting.
|
|
# use_default_interface=true
|
|
|
|
[Scan]
|
|
#
|
|
# Disable periodic scan. Setting this option to 'true' will prevent iwd from
|
|
# issuing the periodic scans for the available networks while disconnected.
|
|
# The behavior of the user-initiated scans isn't affected.
|
|
# The periodic scan is enabled by default.
|
|
#disable_periodic_scan=true
|
|
#
|
|
|
|
#
|
|
# Disable roaming scan. Setting this option to 'true' will prevent iwd from
|
|
# issuing the roaming scans for the available networks while connected.
|
|
# The behavior of the user-initiated scans isn't affected.
|
|
# The roaming scan is enabled by default.
|
|
#disable_roaming_scan=true
|
|
#
|
|
|
|
#
|
|
# Disable MAC address randomization. Setting this option to 'true' will prevent
|
|
# the capable network adapters from randomizing MAC addresses during the active
|
|
# scans for networks, thus decreasing user privacy.
|
|
# The MAC address randomization is enabled by default.
|
|
#disable_mac_address_randomization=true
|
|
#
|
|
|
|
[Blacklist]
|
|
#
|
|
# Configure BSS blacklist time/multipler/max. If a connection to a BSS fails for
|
|
# whatever reason we can avoid connecting to this BSS in the future by
|
|
# blacklisting it. These three options configure how long a BSS is blacklisted
|
|
# for.
|
|
#
|
|
# bss_blacklist_time - The initial timeout for a blacklisted BSS in
|
|
# seconds.
|
|
# bss_blacklist_multiplier - What bss_blacklist_time is multiplied by after
|
|
# future unsuccessful connection attempts in
|
|
# seconds.
|
|
# bss_blacklist_max_time - The maximum time a BSS can be blacklisted for in
|
|
# seconds.
|
|
#
|
|
#bss_blacklist_time=60
|
|
#bss_blacklist_multiplier=30
|
|
#bss_blacklist_max_time=86400
|
|
|
|
[Rank]
|
|
#
|
|
# Manually specify a 5G ranking factor. 5G networks are already preferred but
|
|
# only in terms of calculated data rate, which is RSSI dependent. This means it
|
|
# is still possible for IWD to prefer a 2.4GHz AP in the right conditions.
|
|
# This ranking provides a way to further weight the ranking towards 5G if
|
|
# required. Also, a lower 5G factor could be used to weight 2.4GHz if that is
|
|
# desired.
|
|
#
|
|
#rank_5g_factor=1.0
|