The SAE test made some assumptions on certain conditions due to
there being no way of checking if those conditions were met
Mainly the use of H2E/hunt-and-peck.
We assumed that when we told hostapd to use H2E or hunt/peck it
would but in reality it was not. Hostapd is apparently not very
good at swapping between the two with a simple "reload" command.
Once H2E is enabled it appears that it cannot be undone.
Similarly the vendor elements seem to carry over from test to
test, and sometimes not which causes unintended behavior.
To fix this create separate APs for the specific scenario being
tested:
- Hunt and peck
- H2E
- Special vendor_element simulating buggy APs
Another issue found was that if password identifies are used
hostapd automatically chooses H2E which was not intented, at
least based on the test names (in reality it wasn't causing any
problems).
The tests have also been improved to use hostapds "sta_status"
command which contains the group number used when authenticating,
so now that at least can be verified.
In order to support identifiers the test profiles needed to be
reworked due to hostapd allowing multiple password entires. You
cannot just call set_value() with a new entry as the old ones
still exist. Instead use a unique password for the identifier and
non-identifier use cases.
After adding this test the failure_test started failing due to
hostapd not starting up. This was due to the group being unsupported
but oddly only when hostapd was reloaded (running the test
individually worked). To fix this the group number was changed to 21
which hostapd does support but IWD does not.
Break up the SAE tests into two parts: testSAE and testSAE-AntiClogging
testSAE is simplified to only use two radios and a single phy managed
by hostapd. hostapd configurations are changed via the new 'set_value'
method added to hostapd utils. This allows forcing hostapd to use a
particular sae group set, or force hostapd to use SAE H2E/Hunting and
Pecking Loop for key derivation. A separate test for IKE Group 20 is no
longer required and is folded into connection_test.py
testSAE-AntiClogging is added with an environment for 5 radios instead
of 7, again with hostapd running on a single phy. 'sae_pwe' is used to
force hostapd to use SAE H2E or Hunting and Pecking for key derivation.
Both Anti-Clogging protocol variants are thus tested.
main.conf is added to both directories to force scan randomization off.
This seems to be required for hostapd to work properly on hwsim.
Slower systems may not be able to make some timeouts that tests
mandated. All timeouts were increased significantly to allow tests
to pass on slow systems.
This test was unreliable since it was assuming a periodic scan would
happen at just the right time. Instead since we are expecting autoconnect
we can just wait for DeviceState.connected then after we are connected
verify the network was correct.
Doing this scan causes issues in the test. Like with other autoconnect
tests we can just use the fact that IWD will always be doing a periodic
scan during start up, so we only need to wait for that to finish before
querying the network list.
Don't use del wd to dereference the IWD instance at the end of the function
where it has been defined in the first place as at this point wd is about
to have its reference count decreased anyway (the variable's scope is
ending) so it's pointless (but didn't hurt).
Relying on the __del__ destructor to kill the IWD process in those tests
it has been started in the constructor is a bit of a hack in the first
place, because the destructor is called on garbage collection and even
through CPython does this on the refcount reaching 0, this is not
documented and there's no guideline on when it should happen or if it
should happen at all. So it could be argued that we should keep the del
wd statemenets to be able to easily replace all of them with a call to a
new method. But most of them are not placed so that they're guaranteed
to happen on test success or failure. It would probably be easier to do
this and other housekeeping in a base class and make the tests its
subclasses. Also some of these tests don't really need to launch iwd
themselves, since IWD now tracks changes in the known network files I
think IWD only really needs to be killed between tests when main.conf
changes.
SAE has a clogging test which requires 4 radios to all simultaneously
connect. All the other tests are only using one of these radios, so
in these tests we explicitly disconnect these devices preventing them
from autoconnecting.
