Tests the 3 possible options to UseDefaultEccGroup behave as
expected:
- When not provided use the "auto" behavior.
- When false, always use higher order groups
- When true, always use default group
The SAE test made some assumptions on certain conditions due to
there being no way of checking if those conditions were met
Mainly the use of H2E/hunt-and-peck.
We assumed that when we told hostapd to use H2E or hunt/peck it
would but in reality it was not. Hostapd is apparently not very
good at swapping between the two with a simple "reload" command.
Once H2E is enabled it appears that it cannot be undone.
Similarly the vendor elements seem to carry over from test to
test, and sometimes not which causes unintended behavior.
To fix this create separate APs for the specific scenario being
tested:
- Hunt and peck
- H2E
- Special vendor_element simulating buggy APs
Another issue found was that if password identifies are used
hostapd automatically chooses H2E which was not intented, at
least based on the test names (in reality it wasn't causing any
problems).
The tests have also been improved to use hostapds "sta_status"
command which contains the group number used when authenticating,
so now that at least can be verified.
Modify the existing frequency test to check that the ordering
lines up with the ranking of the BSS.
Add a test to check that quick scans limit the number of known
frequencies.
This was caused by the unused hostapd instance running after being
re-enabled by mistake. This cause an additional scan result with the
same rank to be seen which would then be connected to by luck of the
draw.
This really needs to be done to many more autotests but since this
one seems to have random failures ensure that all the tests still
run if one fails. In addition add better cleanup for hwsim rules.
In order to test that extra settings are applied prior to connecting
two tests were added for hidden networks as well as one testing if
there is already an existing profile after DPP.
The reason hidden networks were used was due to the requirement of
the "Hidden" settings in the profile. If this setting doesn't get
sync'ed to disk the connection will fail.
In order to support identifiers the test profiles needed to be
reworked due to hostapd allowing multiple password entires. You
cannot just call set_value() with a new entry as the old ones
still exist. Instead use a unique password for the identifier and
non-identifier use cases.
After adding this test the failure_test started failing due to
hostapd not starting up. This was due to the group being unsupported
but oddly only when hostapd was reloaded (running the test
individually worked). To fix this the group number was changed to 21
which hostapd does support but IWD does not.
The default() method was added for convenience but was extending the
test times significantly when the hostapd config was lengthy. This
was because it called set_value for every value regardless if it
had changed. Instead store the current configuration and in default()
only reset values that differ.
This tests ensures IWD disconnects after receiving an association
timeout event. This exposes a current bug where IWD does not
transition to disconnected after an association timeout when
FT-roaming.
If tests end in an unknown state it is sometimes required that IWD
be stopped manually in order for future tests to run. Add a stop()
method so test tearDown() methods can explicitly stop IWD.
The path for IWD to call this doesn't ever happen in autotests
but during debugging of the DPP agent it was noticed that the
DBus signature was incorrect and would always result in an error
when calling from IWD.
Several tests do not pass due to some additional changes that have
not been merged. Remove these cases and add some hardening after
discovering some unfortunate wpa_supplicant behavior.
- Disable p2p in wpa_supplicant. With p2p enabled an extra device
is created which starts receiving DPP frames and printing
confusing messages.
- Remove extra asserts which don't make sense currently. These
will be added back later as future additions to PKEX are
upstreamed.
- Work around wpa_supplicant retransmit limitation. This is
described in detail in the comment in pkex_test.py
- wait_for_event was returning a list in certain cases, not the
event itself
- The configurator ID was not being printed (',' instead of '%')
- The DPP ID was not being properly waited for with PKEX
Stop() will now return NotFound if DPP is not running. This causes
the DPP test to fail since it calls this regardless if the protocol
already stopped. Ignore this exception since tests end in various
states, some stopped and some not.
In many tests the hostapd configuration does not include all the
values that a test uses. Its expected that each individual test
will add the values required. In many cases its required each test
slightly alter the configuration for each change every other test
has to set the value back to either a default or its own setting.
This results in a ton of duplicated code mainly setting things
back to defaults.
To help with this problem the hostapd configuration is read in
initially and stored as the default. Tests can then simply call
.default() to set everything back. This significantly reduces or
completely removes a ton of set_value() calls.
This does require that each hostapd configuration file includes all
values any of the subtests will set, which is a small price for the
convenience.
The parsing code was breaking out of the loop on the first comment
which is incorrect and causes only part of the file to be parsed.
Its odd this hasn't popped up until now but its likely due to
differing dhcpd versions, some which add comments and others that
do not.
FILS rekeys were fixed in hostapd somewhat recently but older
versions will fail this test. Document that so we don't get
confused when running tests against older hostapd versions.
This adds another radio so IWD hits the FT failure path after
authentication to the first BSS fails. This causes a wiphy work
item to be rescheduled which previously was unsafe.
AP mode implements a few DBus methods/properties which are named
the same as station: Scan, Scanning, and GetOrderedNetworks. Allow
the Device object to work with these in AP mode by calling the
correct method if the Mode is 'ap'.
The AP mode device APIs were hacked together and only able to start
stop an AP. Now that the AP interface has more functionality its
best to use the DBus class template to access the full AP interface
capabilities.
The disabled cipher list contained a '.' instead of ',' which prevented
the subsequent ciphers from being disabled. This was only group management
ciphers so it didn't have any effect on the test.
The __str__ function assumed station mode which throws an exception
if the device is in AP mode. Fix this as well as print out the mode
the device is in.
This API optimizes scanning to run tests quickly by only scanning
the frequencies which hostapd is using. But if a test doesn't use
hostapd this API raises an uncaught exception.
Check if hostapd is being used, and if not just do a full scan.
This test was taking about 5 minutes to run, specifically
the requested scan test. One slight optimization is to
remove the duplicate hidden network, since there is no
need for two. In addition the requested scan test was
changed so it does not periodic scan and only issues a dbus
scan.
The CI was sometimes taking ~10-15 minutes to run just this
test. This is likely due to the test having 7 radios and
which is a lot of beacons/probes to process.
Disabling the unused hostapd instances drops the runtime down
to about 1 minute.
