This is a fixup for the AP code merge. wsc.c never registered
for handshake events, so in case of failure it was never calling
netdev_handshake_failed, which caused a double free.
Now, a user can setup an AP as follows:
- Set device "Mode" to ap (ap interface will appear on bus)
- call "Start()" on AP interface
Issuing "Stop()" on the AP interface will stop and cleanup
the internal AP structures, but the AP interface will remain
up. To shutdown completely the device Mode must be switched
back to station. If the AP interface is running, the Mode can
directly be switched to station without calling Stop; this
has the same effect and will take down the AP interface.
Handshake related netdev events were removed in favor of
handshake events. Now events will be emitted on the handshake
object related to the 4-way handshake and key settings. Events
are:
HANDSHAKE_EVENT_STARTED
HANDSHAKE_EVENT_SETTING_KEYS
HANDSHAKE_EVENT_COMPLETE
HANDSHAKE_EVENT_FAILED
Right now, since netdev only operates in station mode, nothing
listens for COMPLETE/FAILED, as device/wsc gets notified by the
connect_cb when the connection was successful. The COMPLETE/
FAILED were added in preperation for AP moving into eapol/netdev.
As a temporary DBus API to switch between Station and Access Point
modes, add two methods on the Device interface. Add a new state
DEVICE_STATE_ACCESS_POINT which is in effect from the moment
StartAccessPoint is received (even before it returns) until
StopAccessPoint returns, there are no intermediate states when the
methods run for simplicity. Add checks across device.c to make sure
Station related functionality is disabled when in Access Point mode.
The kernel doesn't reset the netdev's state to disconnected when it
sends us a beacon loss event so we can't either unless we automatically
send a disconnect command to the kernel.
It seems the handling of beacon loss depends on the driver. For example
in mac80211 only after N beacon loss events (default 7) a probe request is
sent to the AP and a deauthenticate packet is sent if no probe reply is
receiver within T (default 500ms).
Pass an additional parameter to the scan results notify functions to
tell them whether the scan was successful. If it wasn't don't bother
passing an empty bss_list queue, pass NULL as bss_list. This way the
callbacks can tell whether the scan indicates there are no BSSes in
range or simply was aborted and the old scan results should be kept.
This implements very initial support of WPS PIN based connections. The
scanning logic attempts to find an AP in PIN mode and tries to connect
to that AP. We currently do not try multiple APs if available or
implement the WSC 1.0 connection logic.
Trigger a roam attempt when the RSSI level has been low for at least 5
seconds using the netdev RSSI LOW/HIGH events. See if neighbor reports
are supported and if so, request and process the neighbor reports list
to restrict the number of channels to be scanned. The scanning part is
not included in this patch for readability.
Remove the keys and other data from struct eapol_sm, update device.c,
netdev.c and wsc.c to use the handshake_state object instead of
eapol_sm. This also gets rid of eapol_cancel and the ifindex parameter
in some of the eapol functions where sm->handshake->ifindex can be
used instead.
If the device is currently connected, we will initiate a disconnection
(or wait for the disconnection to complete) prior to starting the
WSC-EAP association.
We send the scan results where we obtained a PushButton target over to
device object. If EAP-WSC transaction is successful, then the scan
results are searched to find a network/bss combination found in the
credentials obtained. If found, the network is connected to
automatically.
Previously device.c would remove the whole object at the path of the
Device and the WSC interfaces but now the watches are called without the
whole object appearing and disappearing.
Turn netdev watches into device watches. The intent is to refactor out
netdev specific details into its own class and move device specific
logic into device.c away from wiphy.c