In debug mode the test context is printed before each test. This
adds some additional information in there:
Available Memory: /proc/meminfo: MemAvailable
Last Test Delta: Change in usage between current and last test
Per-test Usage: Graph of usage relative to all past tests. This is
useful for seeing a trend down/up of usage.
This could fail and was not being checked. It was minimally changed to
take the ifindex directly (this was the only thing needed from the ethdev)
which allows checking prior to initializing the ethdev.
Running the tests inside a VM makes it difficult for the host to figure
out if the test actually failed or succeeded. For a human its easy to
read the results table, but for an automated system parsing this would
be fragile. This adds a new option --result <file> which writes PASS/FAIL
to the provided file once all tests are completed. Any failures results in
'FAIL' being written to the file.
\e[1;30m is bold black, often, but not always displayed bright black or
bold bright black. In case it is displayed as real black it is
invisible. \e[1;90m is explicit bold bright black.
\e[37m is white, therefore it is not suitable to be labeled as GREY,
which is \e[90m
The logic here assumed any BSS's in the roam scan were identical to
ones in station's bss_list with the same address. Usually this is true
but, for example, if the BSS changed frequency the one in station's
list is invalid.
Instead when a match is found remove the old BSS and re-insert the new
one.
With the addition of 6GHz '6000' is no longer the maximum frequency
that could be in .known_network.freq. For more robustness
band_freq_to_channel is used to validate the frequency.
Scanning while in AP mode is somewhat of an edge case, but it does
have some usefulness specifically with onboarding new devices, i.e.
a new device starts an AP, a station connects and provides the new
device with network credentials, the new device switches to station
mode and connects to the desired network.
In addition this could be used later for ACS (though this is a bit
overkill for IWD's access point needs).
Since AP performance is basically non-existant while scanning this
feature is meant to be used in a limited scope.
Two DBus API's were added which mirror the station interface: Scan and
GetOrderedNetworks.
Scan is no different than the station variant, and will perform an active
scan on all channels.
GetOrderedNetworks diverges from station and simply returns an array of
dictionaries containing basic information about networks:
{
Name: <ssid>
SignalStrength: <mBm>
Security: <psk, open, or 8021x>
}
Limitations:
- Hidden networks are not supported. This isn't really possible since
the SSID's are unknown from the AP perspective.
- Sharing scan results with station is not supported. This would be a
convenient improvement in the future with respect to onboarding new
devices. The scan could be performed in AP mode, then switch to
station and connect immediately without needing to rescan. A quick
hack could better this situation by not flushing scan results in
station (if the kernel retains these on an iftype change).
This was already implemented in station but with no dependency on
that module at all. AP will need this for a scanning API so its
being moved into scan.c.
The 802.11ax standards adds some restrictions for the 6GHz band. In short
stations must use SAE, OWE, or 8021x on this band and frame protection is
required.
All uses of this macro will work with a bitwise comparison which is
needed for 6GHz checks and somewhat more flexible since it can be
used to compare RSN info, not only single AKM values.
This adds checks if MFP is set to 0 or 1:
0 - Always fail if the frequency is 6GHz
1 - Fail if MFPC=0 and the frequency is 6GHz.
If HW is capable set MFPR=1 for 6GHz
This is a new band defined in the WiFi 6E (ax) amendment. A completely
new value is needed due to channel reuse between 2.4/5 and 6GHz.
util.c needed minimal updating to prevent compile errors which will
be fixed later to actually handle this band. WSC also needed a case
added for 6GHz but the spec does not outline any RF Band value for
6GHz so the 5GHz value will be returned in this case.
sae.c was failing to build on some platforms:
error: implicit declaration of function 'reallocarray'; did you mean 'realloc'?
[-Werror=implicit-function-declaration]
In certain rare cases IWD gets a link down event before nl80211 ever sends
a disconnect event. Netdev notifies station of the link down which causes
station to be freed, but netdev remains in the same state. Then later the
disconnect event arrives and netdev still thinks its connected, calls into
(the now freed) station object and causes a crash.
To fix this netdev_connect_free() is now called on any link down events
which will reset the netdev object to a proper state.
src/netdev.c:netdev_link_notify() event 16 on ifindex 16
src/netdev.c:netdev_mlme_notify() MLME notification Del Station(20)
src/netdev.c:netdev_link_notify() event 16 on ifindex 16
src/netdev.c:netdev_mlme_notify() MLME notification Deauthenticate(39)
src/netdev.c:netdev_deauthenticate_event()
src/netdev.c:netdev_link_notify() event 16 on ifindex 16
src/station.c:station_free()
src/netconfig.c:netconfig_destroy()
src/resolve.c:resolve_systemd_revert() ifindex: 16
src/station.c:station_roam_state_clear() 16
src/netdev.c:netdev_mlme_notify() MLME notification Disconnect(48)
src/netdev.c:netdev_disconnect_event()
Received Deauthentication event, reason: 3, from_ap: false
0 0x472fa4 in station_disconnect_event src/station.c:2916
1 0x472fa4 in station_netdev_event src/station.c:2954
2 0x43a262 in netdev_disconnect_event src/netdev.c:1213
3 0x43a262 in netdev_mlme_notify src/netdev.c:5471
4 0x6706eb in process_multicast ell/genl.c:1029
5 0x6706eb in received_data ell/genl.c:1096
6 0x65e630 in io_callback ell/io.c:120
7 0x65a94e in l_main_iterate ell/main.c:478
8 0x65b0b3 in l_main_run ell/main.c:525
9 0x65b0b3 in l_main_run ell/main.c:507
10 0x65b5cc in l_main_run_with_signal ell/main.c:647
11 0x4124d7 in main src/main.c:532
If an event is in response to some command which is returning an
unexpected value (unexpected with respect to wpas.py) handle_eow
would raise an exception.
Specifically with DPP this was being hit when the URI was being
returned.
