The parsing code was breaking out of the loop on the first comment
which is incorrect and causes only part of the file to be parsed.
Its odd this hasn't popped up until now but its likely due to
differing dhcpd versions, some which add comments and others that
do not.
Test that the DHCPv4 lease got renewed after the T1 timer runs out.
Then also simulate the DHCPREQUEST during renew being lost and
retransmitted and the lease eventually getting renewed T1 + 60s later.
The main downside is that this test will inevitably take a while if
running in Qemu without the time travel ability.
Update the test and some utility code to run hostapd in an isolated net
namespace for connection_test.py. We now need a second hostapd
instance though because in static_test.py we test ACD and we need to
produce an IP conflict. Moving the hostapd instance unexpectedly fixes
dhcpd's internal mechanism to avoid IP conflicts and it would no longer
assign 192.168.1.10 to the second client, it'd notice that address was
already in use and assign the next free address, or fail if there was
none. So add a second hostapd instance that runs in the main namespace
together with the statically-configured client, it turns out the test
relies on the kernel being unable to deliver IP traffic to interfaces on
the same system.
Add a fake resolvconf executable to verify that the right nameserver
addresses were actually committed by iwd. Again use unique nameserver
addresses to reduce the possibility that the test succeeds by pure luck.
Extend test_ip_address_match to support IPv6 and to test the
netmask/prefix length while it reads the local address since those are
retrieved using the same API.
Modify testNetconfig to validate the prefix lengths, change the prefix
lengths to be less common values (not 24 bits for IPv4 or 64 for IPv6),
minor cleanup.
- Setting the IP address was resulting in an error:
Error: any valid prefix is expected rather than "wln58".
This is fixed by reordering the arguments with the IP address first
- Remove the sleep, and use non_block_wait to wait for the IPv6 address
to be set.
On some systems the default radvd pid file location is not accessible.
Specify it to be under /tmp instead.
While there, enable full radvd debug output so it is logged when
test-runner is invoked with the --log option.
This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
Tests netconfig with a static configuration, as well as tests ACD
functionality.
The test has two IWD radios which will eventually use the same IP.
One is configured statically, one will receive the IP via DHCP.
The static client sets its IP first and begins using it. Then the
DHCP client is started. Since ACD in a DHCP client is configured
to use its address indefinitely, the static client *should* give
up its address.
If running multiple tests testNetconfig would fail due to the
hardcoded wln0 in the dhcpd.conf file. dhcpd can actually start
by passing in the interface to the run command rather than
inside the config file.
The interface was hard coded to wln0 which works when running single
tests but not when running multiple. Instead use the actual ifname
that hostapd is using.
Tests that DHCP using IWD's internal netconfig functions properly.
The actual IP address assignment is not verified, but since IWD does
not signal the connection as successful unless DHCP succeeds we
can assume it was successful by checking that the device is connected.
The process of actually starting dhcpd and configuring the interfaces
is quite simple so it was left in the autotest itself. If (or when)
more tests require IP capabilities (p2p, FILS, etc) this could be
moved into test-runner itself and be made common. The reason I did not
put it in there now is a) because this is the only test and b) more
complex DHCP cases are likely to develop and may require more than this
simplistic setup (like multiple APs/interfaces)
James Prestwood