Yet another weird UML quirk. The intent of this tests was to ensure
the profile gets encrypted, and to check this both the mtime and
contents of the profile were checked.
But under UML the profile is copied, IWD started, and the profile
is encrypted all without any time passing. The (same) mtime was
then updated without any changes which fails the mtime check.
This puts a sleep after copying the profile to ensure the system
time differs once IWD encrypts the profile.
In UML if any process dies while test-runner is waiting for the DBus
service or some socket to be available it will block forever. This
is due to the way the non_block_wait works.
Its not optimal but it essentially polls over some input function
until the conditions are met. And, depending on the input function,
this can cause UML to hang since it never has a chance to go idle
and advance the time clock.
This can be fixed, at least for services/sockets, by sleeping in
the input function allowing time to pass. This will then allow
test-runner to bail out with an exception.
This patch adds a new wait_for_service function which handles this
automatically, and wait_for_socket was refactored to behave
similarly.
This function was checking if the process object exists, which can
persist long after a process is killed, or dies unexpectedly. Check
that the actual PID exists by sending signal 0.
The man pages (iwd.network) have a section about how to name provisioning
files containing non-alphanumeric characters but not everyone reads the
entire man page.
Warning them that the provisioning file was not read and pointing to
'man iwd.network' should lead someone in the right direction.
EAP-Success might come in with an identifier that is incremented by 1
from the last Response packet. Since identifier field is a byte, the
value might overflow (from 255 -> 0.) This overflow isn't handled
properly resulting in EAP-Success/Failure packets with a 0 identifier
due to overflow being erroneously ignored. Fix that.
test_decryption_failure is quite simple and only verifies that a known
network exists after starting. This causes the test to end before IWD can
fully start up leaving the DBus utilities in limbo having not fully
initialized.
Then, on the next test, stale InterfaceAdded signals arrive (for Station
and P2P) which throw exceptions when trying to get the bus (since IWD is
long gone). In addition the next IWD instance has started so any paths
included in the InterfaceAdded signals are bogus and cause additional
exceptions.
At the end of this test we can call list_devices() which will wait for
the InterfaceAdded signal, and cleanly exit afterwards.
An earlier commit fixed several options but ended up breaking others. The
result_parent/monitor_parent options are hidden from the user and only meant
to be passed to the kernel but they relied on the fact that the underscore
was present, not a dash. This updates the argument to use a dash:
--result-parent
--monitor-parent
Fixes: 00e41eb0ff ("test-runner: Fix parsing for some arguments")
The new regex match update was actually matching way more than it should
have due to how python's 'match' API works. 'match' will return successfully
if zero or more characters match from the beginning of the string. In this
case we actually need the entire regex to match otherwise we start matching
all prefixes, for example:
"--verbose iwd" will match iwd, iwd-dhcp, iwd-acd, iwd-genl and iwd-tls.
Instead use re.fullmatch which requires the entire string to match the
regex.
This was copy pasted from the autoconnect test, and depending on
how the python module cache is ordered can incorrectly use the
wrong test class. This should nothappen because we insert
the paths to the head of the list but for consistency the class
should be named something that reflects what the test is doing.
Enabling this ends up dumping so much logging and, at least with namespaces,
seems to break the logger module and cause really weird behavior, worst of
which is that all processes start dumping to stdout.
This can still be enabled explicitly with --verbose iwd-rtnl, but is turned
off by default when --log is used.
Add a fake resolvconf executable to verify that the right nameserver
addresses were actually committed by iwd. Again use unique nameserver
addresses to reduce the possibility that the test succeeds by pure luck.
In static_test.py add IPv6. Add comments on what we're actually testing
since it wasn't very clear. After the expected ACD conflict detection,
succeed if either the lost address was removed or the client disconnected
from the AP since this seems like a correct action for netconfig to
implement.
In iwd.py make sure all the static methods that touch IWD storage take the
storage_dir parameter instead of hardcoding IWD_STORAGE_DIR, and make
sure that parameter is actually used.
Create the directory if it doesn't exist before copying files into it.
This fixes a problem in testNetconfig where
`IWD.copy_to_storage('ssidTKIP.psk', '/tmp/storage')`
would result in /tmp/storage being created as a file, rather than a
directory containing a file, and resulting in IWD failing to start with:
`Failed to create /tmp/storage`
runner.py creates /tmp/iwd but that doesn't account for IWD sessions
with a custom storage dir path.
Extend test_ip_address_match to support IPv6 and to test the
netmask/prefix length while it reads the local address since those are
retrieved using the same API.
Modify testNetconfig to validate the prefix lengths, change the prefix
lengths to be less common values (not 24 bits for IPv4 or 64 for IPv6),
minor cleanup.
Currently the parameter values reach run-tests by first being parsed by
runner.py's RunnerArgParser, then the resulting object members being
encoded as a commandline string, then as environment variables, then the
environment being converted to a python string list and passed to
RunnerCoreArgParser again. Where argument names (like --sub-tests) had
dashes, the object members had underscores (.sub_tests), this wasn't
taken into account when building the python string list from environment
variables so convert all underscores to dashes and hope that all the
names match now.
Additionally some arguments used nargs='1' or nargs='*' which resulted
in their python values becoming lists. They were converted back to command
line arguments such as: --sub_tests ['static_test.py'], and when parsed
by RunnerCoreArgParser again, the values ended up being lists of lists.
In all three cases it seems the actual user of the parsed value actually
expects a single string with comma-separated substrings in it so just drop
the nargs= uses.
Most users of storage_network_open don't log errors when the function
returns a NULL and fall back to defaults (empty l_settings).
storage_network_open() itself only logs errors if the flie is encrypted.
Now also log an error when l_settings_load_from_file() fails to help track
down potential syntax errors.
Drop the wrong negation in the error check. Check that there are no extra
characters after prefix length suffix. Reset errno 0 before the strtoul
call, as recommended by the manpage.
This is actually a false positive only because
p2p_device_validate_conn_wfd bails out if the IE is NULL which
avoids using wfd_data_length. But its subtle and without inspecting
the code it does seem like the length could be used uninitialized.
src/p2p.c:940:7: error: variable 'wfd_data_len' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
if (dev->conn_own_wfd)
^~~~~~~~~~~~~~~~~
src/p2p.c:946:8: note: uninitialized use occurs here
wfd_data_len))
^~~~~~~~~~~~
src/p2p.c:940:3: note: remove the 'if' if its condition is always true
if (dev->conn_own_wfd)
^~~~~~~~~~~~~~~~~~~~~~
src/p2p.c:906:23: note: initialize the variable 'wfd_data_len' to silence this warning
ssize_t wfd_data_len;
^
= 0
Though the documentation for NLMSG_OK uses an int type for the length
the actual check is based on nlmsghdr->nlmsg_len which is a 32 bit
unsigned integer. Clang was complaining about one call in nlmon.c
because nlmsg_len was int type. Every other usage in nlmon.c uses
a uint32_t, so use that both for consistency and to fix the warning.
monitor/nlmon.c:7998:29: error: comparison of integers of different
signs: '__u32' (aka 'unsigned int') and 'int'
[-Werror,-Wsign-compare]
for (nlmsg = iov.iov_base; NLMSG_OK(nlmsg, nlmsg_len);
^~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/include/linux/netlink.h💯24: note: expanded from macro 'NLMSG_OK'
(nlh)->nlmsg_len <= (len))
On musl-gcc the compiler is giving a warning for igtk_key_index
and gtk_key_index being used uninitialized. This isn't possible
since they are only used if gtk/igtk are non-NULL so pragma to
ignore the warning.
src/fils.c: In function 'fils_rx_associate':
src/fils.c:580:17: error: 'igtk_key_index' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
580 | handshake_state_install_igtk(fils->hs,
igtk_key_index,igtk + 6,
igtk_len - 6, igtk);
(same error for gtk_key_index)
Since commit 922fa099721903b106a7bc1ccd1ffe8c4a7bce69 in hostap, our
setting of config_methods on P2P-client interface was ignored. Work
around that commit, in addition to the previous workaround we have in
this test, to again ensure the correct config_methods value is used.
This was lazily copied from UML but really made no sense in the context
of QEMU. First QEMU needs the virtfs option to define the mount tag and
in addition a 9p mount should be used rather than 'hostfs'.
The glob match was completely broken for --verbose because globs
are actually path matches, not generally for strings. Instead
match based on regular expressions.
First the verbose option was fixed to store it as an array as well
as write any list arguments into the kernel command line properly
(str() would include []). This has worked up until now because the
'in' keyword in python will work on strings just as well
as lists, for example:
>>> 'test' in 'this,is,a,test'
True
Then, the glob match was replaced with a regex match. Any exceptions
are caught and somewhat ignored (printed, but only seen with --debug).
This only guards against fatal exceptions from a user passing an
invalid expression.
For network configuration files the man pages (iwd.network) state
that [General].{AlwaysRandomizeAddress,AddressOverride} are only
used if main.conf has [General].AddressRandomization=network.
This actually was not being enforced and both iwd.network settings
were still taken into account regardless of what AddressRandomization
was set to (even disabled).
The handshake setup code now checks the AddressRandomization value
and if anything other than 'network' skips the randomization.
This bit of code was throwing exceptions if a test cleaned up files that
test-runner was expecting to clean up. Specifically testHotspot swaps out
main.conf and PSK files many times. This led to the exception being thrown,
caught, and ignored but further on test-runner would print:
"File _X_ not cleaned up!"
Now the files will be checked if they exist before trying to remove it.
There were a few places in dpp/dpp-util which passed a single byte but
was being read in with va_arg(va, size_t). On some architectures this was
causing failures presumably from the compiler using an integer type
smaller than size_t. As we do elsewhere, cast to size_t to force the
compiler to pass a properly sized iteger to va_arg.
Similarly to ofono/phonesim allow tests to be skipped if wpa_supplicant
is not found on the system.
This required some changes to DPP/P2P where Wpas() should be called first
since this can now throw a SkipTest exception.
The Wpas class was also made to allow __del__ to be called without
throwing additional exceptions in case wpa_supplicant was not found.
This allows the EAP tests to pass, but the fix really needs to be in
hostapd itself. Hostapd currently tries to lookup the EAP session
immediately after receiving EAPOL_REAUTH. This uses the identity
it has stored which, in the case of PEAP/TTLS, will always be a phase2
identity. During this initial lookup hostapd hard codes the identity
to be phase1 which is not true for PEAP/TTLS, and the lookup fails.
The current way this was being done was to import collections and
use collections.Mapping. This has been deprecated since python 3.3
but has worked up until python 3.10. After python 3.10 this will
no longer work, and Mapping must be imported from collections.abc.
This was passing IFNAME= along with EAPOL_REAUTH which does not work
in the context of a hostapd socket where the iface is already implied.
This fixes that issue as well as resets the events array and actually
waits for the required events afterwards.
After one of the eap-tls-common-based methods succeeds keep the TLS
tunnel instance until the method is freed, rather than free it the
moment the method succeeds. This fixes repeated method runs where until
now each next run would attempt to create a new TLS tunnel instance
but would have no authentication data (CA certificate, client
certificate, private key and private key passphrase) since those are
were by the old l_tls object from the moment of the l_tls_set_auth_data()
call.
Use l_tls_reset() to reset the TLS state after method success, followed
by a new l_tls_start() when the reauthentication starts.
The signal agent notifications were changed which breaks this test.
Specifically commit ce227e7b94 sends a notification when connected
which breaks the 'agent.calls' check. Since this check is done both
after connecting and once already connected the initial value may
be 1 or 0. Because of this that check was removed entirely.
This test was just piping the PSK files into /tmp/iwd/ssidCCMP.psk
which is a bit fragile if the storage dir was ever to change. Instead
use copy_to_storage and the 'name' keyword to copy the file.
If the user specifies the same parent directory for several outfiles
skip mounting since it already exists. For example:
--monitor /outfiles/monitor.txt --result /outfiles/result.txt
Inside the virtual environments /tmp is mounted as its own FS and not
taken from the host. This poses issues if any output files are directly
under /tmp since test-runner tries to mount the parent directory (/tmp).
The can be fixed by ensuring these output files are either not under
/tmp or at least one folder down the tree (e.g. /tmp/outputs/outfile.txt).
Now this requirement is enforced and test-runner will not start if any
output files parent directory is /tmp.
Usually the test home directory is a git repo somewhere e.g. under
/home. But if the home directory is located under /tmp this poses
a problem since UML remounts /tmp. To handle both cases mount
the home directory explicity.
Certain aspects of QEMU like mounting host directories may still require
root access but for UML this is not the case. To handle both cases first
check if SUDO_UID/GID are set and use those to obtain the actual users
ID's. Otherwise if running as non-root use the UID/GID of the user
directly.
