If a user connection fails on a freshly scanned psk or open hidden
network, during passphrase request or after, it shall be removed from
the network list. Otherwise, it would be possible to directly connect
to that known network, which will appear as not hidden.
p2p_peer_update_existing may be called with a scan_bss struct built from
a Probe Request frame so it can't access bss->p2p_probe_resp_info even
if peer->bss was built from a Probe Response. Check the source frame
type of the scan_bss struct before updating the Device Address.
This fixes one timing issue that would make the autotest fail often.
Since l_malloc is used the frame contents are not zero'ed automatically
which could result in random bytes being present in the frame which were
expected to be zero. This poses a problem when calculating the MIC as the
crypto operations are done on the entire frame with the expectation of
the MIC being zero.
Fixes: 83212f9b23 ("eapol: change eapol_create_common to support FILS")
explicit_bzero is used in src/storage.c since commit
01cd858760 but src/missing.h is not
included, as a result build with uclibc fails on:
/home/buildroot/autobuild/instance-0/output-1/host/lib/gcc/powerpc-buildroot-linux-uclibc/10.3.0/../../../../powerpc-buildroot-linux-uclibc/bin/ld: src/storage.o: in function `storage_init':
storage.c:(.text+0x13a4): undefined reference to `explicit_bzero'
Fixes:
- http://autobuild.buildroot.org/results/2aff8d3d7c33c95e2c57f7c8a71e69939f0580a1
This is used to hold the current BSS frequency which will be
used after IWD receives a presence announcement. Since this was
not being set, the logic was always thinking there was a channel
mismatch (0 != current_freq) and attempting to go offchannel to
'0' which resulted in -EINVAL, and ultimately protocol termination.
The logic here assumed any BSS's in the roam scan were identical to
ones in station's bss_list with the same address. Usually this is true
but, for example, if the BSS changed frequency the one in station's
list is invalid.
Instead when a match is found remove the old BSS and re-insert the new
one.
With the addition of 6GHz '6000' is no longer the maximum frequency
that could be in .known_network.freq. For more robustness
band_freq_to_channel is used to validate the frequency.
Scanning while in AP mode is somewhat of an edge case, but it does
have some usefulness specifically with onboarding new devices, i.e.
a new device starts an AP, a station connects and provides the new
device with network credentials, the new device switches to station
mode and connects to the desired network.
In addition this could be used later for ACS (though this is a bit
overkill for IWD's access point needs).
Since AP performance is basically non-existant while scanning this
feature is meant to be used in a limited scope.
Two DBus API's were added which mirror the station interface: Scan and
GetOrderedNetworks.
Scan is no different than the station variant, and will perform an active
scan on all channels.
GetOrderedNetworks diverges from station and simply returns an array of
dictionaries containing basic information about networks:
{
Name: <ssid>
SignalStrength: <mBm>
Security: <psk, open, or 8021x>
}
Limitations:
- Hidden networks are not supported. This isn't really possible since
the SSID's are unknown from the AP perspective.
- Sharing scan results with station is not supported. This would be a
convenient improvement in the future with respect to onboarding new
devices. The scan could be performed in AP mode, then switch to
station and connect immediately without needing to rescan. A quick
hack could better this situation by not flushing scan results in
station (if the kernel retains these on an iftype change).
This was already implemented in station but with no dependency on
that module at all. AP will need this for a scanning API so its
being moved into scan.c.
The 802.11ax standards adds some restrictions for the 6GHz band. In short
stations must use SAE, OWE, or 8021x on this band and frame protection is
required.
All uses of this macro will work with a bitwise comparison which is
needed for 6GHz checks and somewhat more flexible since it can be
used to compare RSN info, not only single AKM values.
This adds checks if MFP is set to 0 or 1:
0 - Always fail if the frequency is 6GHz
1 - Fail if MFPC=0 and the frequency is 6GHz.
If HW is capable set MFPR=1 for 6GHz
This is a new band defined in the WiFi 6E (ax) amendment. A completely
new value is needed due to channel reuse between 2.4/5 and 6GHz.
util.c needed minimal updating to prevent compile errors which will
be fixed later to actually handle this band. WSC also needed a case
added for 6GHz but the spec does not outline any RF Band value for
6GHz so the 5GHz value will be returned in this case.
sae.c was failing to build on some platforms:
error: implicit declaration of function 'reallocarray'; did you mean 'realloc'?
[-Werror=implicit-function-declaration]
In certain rare cases IWD gets a link down event before nl80211 ever sends
a disconnect event. Netdev notifies station of the link down which causes
station to be freed, but netdev remains in the same state. Then later the
disconnect event arrives and netdev still thinks its connected, calls into
(the now freed) station object and causes a crash.
To fix this netdev_connect_free() is now called on any link down events
which will reset the netdev object to a proper state.
src/netdev.c:netdev_link_notify() event 16 on ifindex 16
src/netdev.c:netdev_mlme_notify() MLME notification Del Station(20)
src/netdev.c:netdev_link_notify() event 16 on ifindex 16
src/netdev.c:netdev_mlme_notify() MLME notification Deauthenticate(39)
src/netdev.c:netdev_deauthenticate_event()
src/netdev.c:netdev_link_notify() event 16 on ifindex 16
src/station.c:station_free()
src/netconfig.c:netconfig_destroy()
src/resolve.c:resolve_systemd_revert() ifindex: 16
src/station.c:station_roam_state_clear() 16
src/netdev.c:netdev_mlme_notify() MLME notification Disconnect(48)
src/netdev.c:netdev_disconnect_event()
Received Deauthentication event, reason: 3, from_ap: false
0 0x472fa4 in station_disconnect_event src/station.c:2916
1 0x472fa4 in station_netdev_event src/station.c:2954
2 0x43a262 in netdev_disconnect_event src/netdev.c:1213
3 0x43a262 in netdev_mlme_notify src/netdev.c:5471
4 0x6706eb in process_multicast ell/genl.c:1029
5 0x6706eb in received_data ell/genl.c:1096
6 0x65e630 in io_callback ell/io.c:120
7 0x65a94e in l_main_iterate ell/main.c:478
8 0x65b0b3 in l_main_run ell/main.c:525
9 0x65b0b3 in l_main_run ell/main.c:507
10 0x65b5cc in l_main_run_with_signal ell/main.c:647
11 0x4124d7 in main src/main.c:532
The difference between the existing code is that IWD will send the
authentication request, making it the initiator.
This handles the use case where IWD is provided a peers URI containing
its bootstrapping key rather than IWD always providing its own URI.
A new DBus API was added, ConfigureEnrollee().
Using ConfigureEnrollee() IWD will act as a configurator but begin by
traversing a channel list (URI provided or default) and waiting for
presence announcements (with one caveat). When an announcement is
received IWD will send an authentication request to the peer, receive
its reply, and send an authentication confirm.
As with being a responder, IWD only supports configuration to the
currently connected BSS and will request the enrollee switch to this
BSS's frequency to preserve network performance.
The caveat here is that only one driver (ath9k) supports multicast frame
registration which prevents presence frame from being received. In this
case it will be required the the peer URI contains a MAC and channel
information. This is because IWD will jump right into sending auth
requests rather than waiting for a presence announcement.
The frame watch which covers the presence procedure (and most
frames for that matter) needs to support multicast frames for
presence to work. Doing this in frame-xchg seems like the right
choice but only ath9k supports multicast frame registration.
Because of this limited support DPP will register for these frames
manually.
Parses K (key), M (mac), C (class/channels), and V (version) tokens
into a new structure dpp_uri_info. H/I are not parsed since there
currently isn't any use for them.
This was caught by static analysis. As is common this should never
happen in the real world since the only way this can fail (apart from
extreme circumstances like OOM) is if the key size is incorrect, which
it will never be.
Static analysis flagged that 'path' was never being checked (which
should not ever be NULL) but during that review I noticed stat()
was being called, then fstat afterwards.
Recently systemd added the ability to pass secret credentials to
services via LoadCredentialEncrypted/SetCredentialEncrypted. Once
set up the service is able to read the decrypted credentials from
a file. The file path is found in the environment variable
CREDENTIALS_DIRECTORY + an identifier. The value of SystemdEncrypt
should be set to the systemd key ID used when the credential was
created.
When SystemdEncrypt is set IWD will attempt to read the decrypted
secret from systemd. If at any point this fails warnings will be
printed but IWD will continue normally. Its expected that any failures
will result in the inability to connect to any networks which have
previously encrypted the passphrase/PSK without re-entering
the passphrase manually. This could happen, for example, if the
systemd secret was changed.
Once the secret is read in it is set into storage to be used for
profile encryption/decryption.
Using storage_decrypt() hotspot can also support profile encyption.
The hotspot consortium name is used as the 'ssid' since this stays
consistent between hotspot networks for any profile.
Some users don't like the idea of storing network credentials in
plaintext on the file system. This patch implements an option to
encrypt such profiles using a secret key. The origin of the key can in
theory be anything, but would typically be provided by systemd via
'LoadEncryptedCredential' setting in the iwd unit file.
The encryption operates on the entire [Security] group as well as all
embedded groups. Once encrypted the [Security] group will be replaced
with two key/values:
EncryptedSalt - A random string of bytes used for the encryption
EncryptedSecurity - A string of bytes containing the encrypted
[Security] group, as well as all embedded groups.
After the profile has been encrypted these values should not be
modified. Note that any values added to [Security] after encryption
has no effect. Once the profile is encrypted there is no way to modify
[Security] without manually decrypting first, or just re-creating it
entirely which effectively treated a 'new' profile.
The encryption/decryption is done using AES-SIV with a salt value and
the network SSID as the IV.
Once a key is set any profiles opened will automatically be encrypted
and re-written to disk. Modules using network_storage_open will be
provided the decrypted profile, and will be unaware it was ever
encrypted in the first place. Similarly when network_storage_sync is
called the profile will by automatically encrypted and written to disk
without the caller needing to do anything special.
A few private storage.c helpers were added to serve several purposes:
storage_init/exit():
This sets/cleans up the encryption key direct from systemd then uses
extract and expand to create a new fixed length key to perform
encryption/decryption.
__storage_decrypt():
Low level API to decrypt an l_settings object using a previously set
key and the SSID/name for the network. This returns a 'changed' out
parameter signifying that the settings need to be encrypted and
re-written to disk. The purpose of exposing this is for a standalone
decryption tool which does not re-write any settings.
storage_decrypt():
Wrapper around __storage_decrypt() that handles re-writing a new
profile to disk. This was exposed in order to support hotspot profiles.
__storage_encrypt():
Encrypts an l_settings object and returns the full profile as data
This got merged without a few additional fixes, in particular an
over 80 character line and incorrect length check.
Fixes: d8116e8828 ("dpp-util: add dpp_point_from_asn1()")
When we detect a new phy being added, we schedule a filtered dump of
the newly detected WIPHY and associated INTERFACEs. This code path and
related processing of the dumps was mostly shared with the un-filtered
dump of all WIPHYs and INTERFACEs which is performed when iwd starts.
This normally worked fine as long as a single WIPHY was created at a
time. However, if multiphy new phys were detected in a short amount of
time, the logic would get confused and try to process phys that have not
been probed yet. This resulted in iwd trying to create devices or not
detecting devices properly.
Fix this by only processing the target WIPHY and related INTERFACEs
when the filtered dump is performed, and not any additional ones that
might still be pending.
While here, remove a misleading comment:
manager_wiphy_check_setup_done() would succeed only if iwd decided to
keep the default interfaces created by the kernel.
This debug print was before any checks which could bail out prior to
autoconnect starting. This was confusing because debug logs would
contain multiple "station_autoconnect_start()" prints making you think
autoconnect was started several times.
The periodic scan code was refactored to make normal scans and
periodic scans consistent by keeping both in the same queue. But
that change left out the abort path where periodic scans were not
actually removed from the queue.
This fixes a rare crash when a periodic scan has been triggered and
the device goes down. This path never removes the request from the
queue but still frees it. Then when the scan context is removed the
stale request is freed again.
0 0x4bb65b in scan_request_cancel src/scan.c:202
1 0x64313c in l_queue_clear ell/queue.c:107
2 0x643348 in l_queue_destroy ell/queue.c:82
3 0x4bbfb7 in scan_context_free src/scan.c:209
4 0x4c9a78 in scan_wdev_remove src/scan.c:2115
5 0x42fecd in netdev_free src/netdev.c:965
6 0x445827 in netdev_destroy src/netdev.c:6507
7 0x52beb9 in manager_config_notify src/manager.c:765
8 0x67084b in process_multicast ell/genl.c:1029
9 0x67084b in received_data ell/genl.c:1096
10 0x65e790 in io_callback ell/io.c:120
11 0x65aaae in l_main_iterate ell/main.c:478
12 0x65b213 in l_main_run ell/main.c:525
13 0x65b213 in l_main_run ell/main.c:507
14 0x65b72c in l_main_run_with_signal ell/main.c:647
15 0x4124e7 in main src/main.c:532
If netdev_connect_failed is called before netdev_get_oci_cb() the
netdev's handshake will be destroyed and ultimately crash when the
callback is called.
This patch moves the cancelation into netdev_connect_free rather than
netdev_free.
++++++++ backtrace ++++++++
0 0x7f4e1787d320 in /lib64/libc.so.6
1 0x42634c in handshake_state_set_chandef() at src/handshake.c:1057
2 0x40a11b in netdev_get_oci_cb() at src/netdev.c:2387
3 0x483d7b in process_unicast() at ell/genl.c:986
4 0x480d3c in io_callback() at ell/io.c:120
5 0x48004d in l_main_iterate() at ell/main.c:472 (discriminator 2)
6 0x4800fc in l_main_run() at ell/main.c:521
7 0x48032c in l_main_run_with_signal() at ell/main.c:649
8 0x403e95 in main() at src/main.c:532
9 0x7f4e17867b75 in /lib64/libc.so.6
+++++++++++++++++++++++++++
Commit 4d2176df29 ("handshake: Allow event handler to free handshake")
introduced a re-entrancy guard so that handshake_state objects that are
destroyed as a result of the event do not cause a crash. It rightly
used a temporary object to store the passed in handshake. Unfortunately
this caused variable shadowing which resulted in crashes fixed by commit
d22b174a73 ("handshake: use _hs directly in handshake_event").
However, since the temporary was no longer used, this fix itself caused
a crash:
#0 0x00005555f0ba8b3d in eapol_handle_ptk_1_of_4 (sm=sm@entry=0x5555f2b4a920, ek=0x5555f2b62588, ek@entry=0x16, unencrypted=unencrypted@entry=false) at src/eapol.c:1236
1236 handshake_event(sm->handshake,
(gdb) bt
#0 0x00005555f0ba8b3d in eapol_handle_ptk_1_of_4 (sm=sm@entry=0x5555f2b4a920, ek=0x5555f2b62588, ek@entry=0x16, unencrypted=unencrypted@entry=false) at src/eapol.c:1236
#1 0x00005555f0bab118 in eapol_key_handle (unencrypted=<optimized out>, frame=<optimized out>, sm=0x5555f2b4a920) at src/eapol.c:2343
#2 eapol_rx_packet (proto=<optimized out>, from=<optimized out>, frame=<optimized out>, unencrypted=<optimized out>, user_data=0x5555f2b4a920) at src/eapol.c:2665
#3 0x00005555f0bac497 in __eapol_rx_packet (ifindex=62, src=src@entry=0x5555f2b62574 "x\212 J\207\267", proto=proto@entry=34958, frame=frame@entry=0x5555f2b62588 "\002\003",
len=len@entry=121, noencrypt=noencrypt@entry=false) at src/eapol.c:3017
#4 0x00005555f0b8c617 in netdev_control_port_frame_event (netdev=0x5555f2b64450, msg=0x5555f2b62588) at src/netdev.c:5574
#5 netdev_unicast_notify (msg=msg@entry=0x5555f2b619a0, user_data=<optimized out>) at src/netdev.c:5613
#6 0x00007f60084c9a51 in dispatch_unicast_watches (msg=0x5555f2b619a0, id=<optimized out>, genl=0x5555f2b3fc80) at ell/genl.c:954
#7 process_unicast (nlmsg=0x7fff61abeac0, genl=0x5555f2b3fc80) at ell/genl.c:973
#8 received_data (io=<optimized out>, user_data=0x5555f2b3fc80) at ell/genl.c:1098
#9 0x00007f60084c61bd in io_callback (fd=<optimized out>, events=1, user_data=0x5555f2b3fd20) at ell/io.c:120
#10 0x00007f60084c536d in l_main_iterate (timeout=<optimized out>) at ell/main.c:478
#11 0x00007f60084c543e in l_main_run () at ell/main.c:525
#12 l_main_run () at ell/main.c:507
#13 0x00007f60084c5670 in l_main_run_with_signal (callback=callback@entry=0x5555f0b89150 <signal_handler>, user_data=user_data@entry=0x0) at ell/main.c:647
#14 0x00005555f0b886a4 in main (argc=<optimized out>, argv=<optimized out>) at src/main.c:532
This happens when the driver does not support rekeying, which causes iwd to
attempt a disconnect and re-connect. The disconnect action is
taken during the event callback and destroys the underlying eapol state
machine. Since a temporary isn't used, attempting to dereference
sm->handshake results in a crash.
Fix this by introducing a UNIQUE_ID macro which should prevent shadowing
and using a temporary variable as originally intended.
Fixes: d22b174a73 ("handshake: use _hs directly in handshake_event")
Fixes: 4d2176df29 ("handshake: Allow event handler to free handshake")
Reported-By: Toke Høiland-Jørgensen <toke@toke.dk>
Tested-by: Toke Høiland-Jørgensen <toke@toke.dk>
There is no need to punch the holes for netdev/wheel groups to send to
the .Agent interface. This is only done by the iwd daemon itself and
the policy for user 'root' already takes care of this.
A select few drivers send this instead of SIGNAL_MBM. The docs say this
value is the signal 'in unspecified units, scaled to 0..100'. The range
for SIGNAL_MBM is -10000..0 so this can be scaled to the MBM range easy
enough...
Now, this isn't exactly correct because this value ultimately gets
returned from GetOrderedNetworks() and is documented as 100 * dBm where
in reality its just a unit-less signal strength value. Its not ideal, but
this patch at least will fix BSS ranking for these few drivers.
The 'at_console' D-Bus policy setting has been deprecated for more then
10 years and could be ignored at any time in the future. Moreover, while
the intend was to allow locally logged on users to interact with iwd, it
didn't actually do that.
More info at https://www.spinics.net/lists/linux-bluetooth/msg75267.html
and https://gitlab.freedesktop.org/dbus/dbus/-/issues/52
Therefor remove the 'at_console' setting block.
On Debian (based) systems, there is a standard defined group which is
allowed to manage network interfaces, and that is the 'netdev' group.
So add a D-Bus setting block to grant the 'netdev' group that access.
Building on GCC 8 resulted in this compiler error.
src/sae.c:107:25: error: implicit declaration of function 'reallocarray';
did you mean 'realloc'? [-Werror=implicit-function-declaration]
sm->rejected_groups = reallocarray(NULL, 2, sizeof(uint16_t));
src/erp.c:134:10: error: comparison of integer expressions of different
signedness: 'unsigned int' and 'int' [-Werror=sign-compare]
src/eap-ttls.c:378:10: error: comparison of integer expressions of different signedness: 'uint32_t' {aka 'unsigned int'} and 'int' [-Werror=sign-compare]
Fixes the following crash:
#0 0x000211c4 in netdev_connect_event (msg=<optimized out>, netdev=0x2016940) at src/netdev.c:2915
#1 0x76f11220 in process_multicast (nlmsg=0x7e8acafc, group=<optimized out>, genl=<optimized out>) at ell/genl.c:1029
#2 received_data (io=<optimized out>, user_data=<optimized out>) at ell/genl.c:1096
#3 0x76f0da08 in io_callback (fd=<optimized out>, events=1, user_data=0x200a560) at ell/io.c:120
#4 0x76f0ca78 in l_main_iterate (timeout=<optimized out>) at ell/main.c:478
#5 0x76f0cb74 in l_main_run () at ell/main.c:525
#6 l_main_run () at ell/main.c:507
#7 0x76f0cdd4 in l_main_run_with_signal (callback=callback@entry=0x18c94 <signal_handler>, user_data=user_data@entry=0x0)
at ell/main.c:647
#8 0x00018178 in main (argc=<optimized out>, argv=<optimized out>) at src/main.c:532
This crash was introduced in commit:
4d2176df29 ("handshake: Allow event handler to free handshake")
The culprit seems to be that 'hs' is being used both in the caller and
in the macro. Since the macro defines a variable 'hs' in local block
scope, it overrides 'hs' from function scope. Yet (_hs) still evaluates
to 'hs' leading the local variable to be initialized with itself. Only
the 'handshake_event(hs, HANDSHAKE_EVENT_SETTING_KEYS))' is affected
since it is the only macro invocation that uses 'hs' from function
scope. Thus, the crash would only happen on hardware supporting handshake
offload (brcmfmac).
Fix this by removing the local scope variable declaration and evaluate
(_hs) instead.
Fixes: 4d2176df29 ("handshake: Allow event handler to free handshake")
- Ensure that input isn't an empty string
- Ensure that EINVAL errno (which could be optionally returned by
strto{ul|l} is also checked.
- Since strtoul allows '+' and '-' characters in input, ensure that
input which is expected to be an unsigned number doesn't start with
'-'
Given an ASN1 blob of the right form, parse and create
an l_ecc_point object. The form used is specific to DPP
hence why this isn't general purpose and put into dpp-util.
Like in ap.c, allow the event callback to mark the handshake state as
destroyed, without causing invalid accesses after the callback has
returned. In this case the crash was because try_handshake_complete
needed to access members of handshake_state after emitting the event,
as well as access the netdev, which also has been destroyed:
==257707== Invalid read of size 8
==257707== at 0x408C85: try_handshake_complete (netdev.c:1487)
==257707== by 0x408C85: try_handshake_complete (netdev.c:1480)
(...)
==257707== Address 0x4e187e8 is 856 bytes inside a block of size 872 free'd
==257707== at 0x484621F: free (in /usr/libexec/valgrind/vgpreload_memcheck-amd64-linux.so)
==257707== by 0x437887: ap_stop_handshake (ap.c:151)
==257707== by 0x439793: ap_del_station (ap.c:316)
==257707== by 0x43EA92: ap_station_disconnect (ap.c:3411)
==257707== by 0x43EA92: ap_station_disconnect (ap.c:3399)
==257707== by 0x454276: p2p_group_event (p2p.c:1006)
==257707== by 0x439147: ap_event (ap.c:281)
==257707== by 0x4393AB: ap_new_rsna (ap.c:390)
==257707== by 0x4393AB: ap_handshake_event (ap.c:1010)
==257707== by 0x408C7F: try_handshake_complete (netdev.c:1485)
==257707== by 0x408C7F: try_handshake_complete (netdev.c:1480)
(...)
Previously we added logic to defer doing anything in ap_free() to after
the AP event handler has returned so that ap_event() has a chance to
inform whoever called it that the ap_state has been freed. But there's
also a chance that the event handler is destroying both the AP and the
netdev it runs on, so after the handler has returned we can't even use
netdev_get_wdev_id or netdev_get_ifindex. The easiest solution seems to
be to call ap_reset() in ap_free() even if we're within an event handler
to ensure we no longer need any external objects. Also make sure
ap_reset() can be called multiple times.
Another option would be to watch for NETDEV_WATCH_EVENT_DEL and remove
our reference to the netdev (because there's no need actually call
l_rtnl_ifaddr_delete or frame_watch_wdev_remove if the netdev was
destroyed -- frame_watch already tracks netdev removals), or to save
just the ifindex and the wdev id...
The purpose of this was to have a single utility to both cancel an
existing offchannel operation (if one exists) and start a new one.
The problem was the previous offchannel operation was being canceled
first which opened up the radio work queue to other items. This is
not desireable as, for example, a scan would end up breaking the
DPP protocol most likely.
Starting the new offchannel then canceling is the correct order of
operations but to do this required saving the new ID, canceling, then
setting offchannel_id to the new ID so dpp_presence_timeout wouldn't
overwrite the new ID to zero.
This also removes an explicit call to offchannel_cancel which is
already done by dpp_offchannel_start.
Several members are named based on initiator/responder (i/r)
terminology. Eventually both initiator and responder will be
supported so rename these members to use own/peer naming
instead.
ASN1 parsing will soon be required which will need some utilities in
asn1-private.h. To avoid duplication include this private header and
replace the OID's with the defined structures as well as remove the
duplicated macros.
station_set_scan_results takes an autoconnect flag which was being
set true in both regular/quick autoconnect scans. Since OWE networks
are processed after setting the scan results IWD could end up
connecting to a network before all the OWE hidden networks are
populated.
To fix this regular/quick autoconnect results will set the flag to
false, then process OWE networks, then start autoconnect. If any
OWE network scans are pending station_autoconnect_start will fail
but will pick back up after the hidden OWE scan.
scan_request_failed and scan_finished remove the finished scan_request
from the request queue right away, before calling the callback. This
breaks those clients that rely on scan_cancel working on such requests
(i.e. to force the destroy callback to be invoked synchronously, see
a0911ca778 ("station: Make sure roam_scan_id is always canceled").
Fix this by removing the scan_request from the request queue after
invoking the callback. Also provide a re-entrancy guard that will make
sure that the scan_request isn't removed in scan_cancel itself.
There are similar operations being performed but with different
callbacks and userdata, depending on whether 'sr' is NULL or not.
Optimize the function flow slightly to make if-else unnecessary.
While here, update the comment. periodic scans are now scheduled only
based on the periodic timeout timer.
If periodic scan is active and we receive a SCAN_ABORTED event, we would
still invoke the periodic scan callback with an error. This is rather
pointless since the periodic scan callback cannot do anything useful
with this information. Fix that.
We should never reach a point where NEW_SCAN_RESULTS or SCAN_ABORTED are
received before a corresponding TRIGGER_SCAN is received. Even if this
does happen, there's no harm from processing the commands anyway.
This makes it a little easier to book-keep the started variable. Since
scan_request already has a 'passive' bit-field, there should be no
storage penalty.
If scan_cancel is called on a scan_request that is 'finished' but with
the GET_SCAN command still in flight, it will trigger a crash as
follows:
Received Deauthentication event, reason: 2, from_ap: true
src/station.c:station_disconnect_event() 11
src/station.c:station_disassociated() 11
src/station.c:station_reset_connection_state() 11
src/station.c:station_roam_state_clear() 11
src/scan.c:scan_cancel() Trying to cancel scan id 6 for wdev 200000002
src/scan.c:scan_cancel() Scan is at the top of the queue, but not triggered
src/scan.c:get_scan_done() get_scan_done
Aborting (signal 11) [/home/denkenz/iwd-master/src/iwd]
++++++++ backtrace ++++++++
#0 0x7f9871aef3f0 in /lib64/libc.so.6
#1 0x41f470 in station_roam_scan_notify() at /home/denkenz/iwd-master/src/station.c:2285
#2 0x43936a in scan_finished() at /home/denkenz/iwd-master/src/scan.c:1709
#3 0x439495 in get_scan_done() at /home/denkenz/iwd-master/src/scan.c:1739
#4 0x4bdef5 in destroy_request() at /home/denkenz/iwd-master/ell/genl.c:676
#5 0x4c070b in l_genl_family_cancel() at /home/denkenz/iwd-master/ell/genl.c:1960
#6 0x437069 in scan_cancel() at /home/denkenz/iwd-master/src/scan.c:842
#7 0x41dc2e in station_roam_state_clear() at /home/denkenz/iwd-master/src/station.c:1594
#8 0x41dd2b in station_reset_connection_state() at /home/denkenz/iwd-master/src/station.c:1619
#9 0x41dea4 in station_disassociated() at /home/denkenz/iwd-master/src/station.c:1644
The happens because get_scan_done callback is still called as a result of
l_genl_cancel. Add a re-entrancy guard in the form of 'canceled'
variable in struct scan_request. If set, get_scan_done will skip invoking
scan_finished.
It isn't clear what 'l_queue_peek_head() == results->sr' check was trying
to accomplish. If GET_SCAN dump was scheduled, then it should be
reported. Drop it.
results->sr is set to NULL for 'opportunistic' scans which were
triggered externally. See scan_notify() for details. However,
get_scan_done would only invoke scan_finished (and thus the periodic
scan callback sc->sp.callback) only if the scan queue was empty. It
should do so in all cases.
The point type was being hard coded to 0x3 (BIT1) which may have resulted
in the peer subtracting Y from P when reading in the point (depending on
if Y was odd or not).
Instead set the compressed type to whatever avoids the subtraction which
both saves IWD from needing to do it, as well as the peer.
The intent of this check is to make sure that at least 2 bytes are
available for reading. However, the unintended consequence is that tags
with a zero length at the end of input would be rejected.
While here, rework the check to be more resistant to potential
overflow conditions.
The DPP spec says nothing about how to handle re-transmits but it
was found in testing this can happen relatively easily for a few
reasons.
If the configurator requests a channel switch but does not get onto
the new channel quick enough the enrollee may have already sent the
authenticate response and it was missed. Also by nature of how the
kernel goes offchannel there are moments in time between ROC when
the card is idle and not receiving any frames.
Only frames where there was no ACK will be retransmitted. If the
peer received the frame and dropped it resending the same frame wont
do any good.
Now the result is sent immediately. Prior a connect attempt or
scan could have started, potentially losing this frame. In addition
the offchannel operation is cancelled after sending the result
which will allow the subsequent connect or scan to happen much
faster since it doesn't have to wait for ROC to expire.
The previous (incorrect) else was removed since it ended up
printing in most cases since the if clause returned. This should
have been an else if conditional from the start and only print if the
station device was not found.
IWD may be in the middle of some long operation, e.g. scanning.
If the URI is returned before IWD is ready, a configurator could
start sending frames and IWD either wont receive them, or will
be unable to respond quickly.
The offchannel priority was also changed to zero, which matches the
priority of frames. Currently there should be no interaction between
offchannel and connect (previous offchannel priority).
Periodic scans were handled specially where they were only
started if no other requests were pending in the scan queue.
This is fine, and what we want, but this can actually be
handled automatically by nature of the wiphy work queue rather
than needing to check the request queue explicitly.
Instead we can insert periodic scans at a lower priority than
other scans. This puts them at the end of the work queue, as
well as allows future requests to jump ahead if a periodic scan
has not yet started.
Eventually, once all pending scans are done, the peridoic scan
may begin. This is no different than the preivous behavior and
avoids the need for any special checks once scan requests
complete.
One check was added to address the problem of the periodic scan
timer firing before the scan could even start. Currently this
happened to be handled fine in scan_periodic_queue, as it checks
the queue length. Since this check was removed we must see check
for this condition inside scan_periodic_timeout.
This adds a priority argument to scan_common rather than hard
coding it when inserting the work item and uses the newly
defined wiphy priority for scanning.
Work priority was never explicitly defined anywhere, and a module
using wiphy_radio_work APIs needed to ensure it was not inserting
at a priority that would interfere with other work.
Now all the types of work have been defined with their own priority
and future priorities can easily be added before, after, or in
between existing priorities.
- Mostly problems with whitespace:
- Use of spaces instead of tabs
- Stray spaces before closing ')
- Missing spaces
- Missing 'void' from function declarations & definitions that
take no arguments.
- Wrong indentation level
When this attribute is included, the initiator is requesting all
future frames be sent on this channel. There is no reason for a
configurator to act on this attribute (at least for now) so the
request frame will be dropped in this case. Enrollees will act
on it by switching to the new channel and sending the authentication
response.
While connected the driver ends up choosing quite small ROC
durations leading to excessive calls to ROC. This also will
negatively effect any wireless performance for the current
network and possibly lead to missed DPP frames.
Currently the enrollee relied on autoconnect to handle connecting
to the newly configured network. This usually resulted in poor
performance since periodic scans are done at large intervals apart.
Instead first check if the newly configured network is already
in IWD's network queue. If so it can be connected to immediately.
If not, a full scan must be done and results given to station.
With better JSON support the configuration request object
can now be fully parsed. As stated in the previous comment
there really isn't much use from the configurator side apart
from verifying mandatory values are included.
This patch also modifies the configuration result to handle
sending non 'OK' status codes in case of JSON parsing errors.
json_iter_parse is only meant to work on objects while
json_iter_next is only meant to work on arrays.
This adds checks in both APIs to ensure they aren't being
used incorrectly.
Arrays can now be parsed using the JSON_ARRAY type (stored in
a struct json_iter) then iterated using json_iter_next. When
iterating the type can be checked with json_iter_get_type. For
each iteration the value can be obtained using any of the type
getters (int/uint/boolean/null).
This adds support for boolean, (unsigned) integers, and
null types. JSON_PRIMITIVE should be used as the type when
parsing and the value should be struct json_iter.
Once parsed the actual value can be obtained using one of
the primitive getters. If the type does not match they will
return false.
If using JSON_OPTIONAL with JSON_PRIMITIVE the resulting
iterator can be checked with json_iter_is_valid. If false
the key/value was not found or the type was not matching.
First, this was renamed to 'count_tokens_in_container' to be
more general purpose (i.e. include future array counting).
The way the tokens are counted also changed to be more intuitive.
While the previous way was correct, it was somewhat convoluted in
how it worked (finding the next parent of the objects parent).
Instead we can use the container token itself as the parent and
begin counting tokens. When we find a token with a parent index
less than the target we have reached the end of this container.
This also works for nested containers, including arrays since we
no longer rely on a key (which an array element would not have).
For example::
{
"first":{"foo":"bar"},
"second":{"foo2":"bar2"}
}
index 0 <overall object>
index 1 "first" with parent 0
index 2 {"foo":"bar"} with parent 1
Counting tokens inside "first"'s object we have:
index 3 "foo" with parent 2
index 4 "bar" with parent 3
If we continue counting we reach:
index 5 "second" with parent 0
This terminates the counting loop since the parent index is
less than '2' (the index of {"foo":"bar"} object).
In file included from ./ell/ell.h:15,
from ../../src/dpp.c:29:
../../src/dpp.c: In function ‘authenticate_request’:
../../ell/log.h:79:22: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 8 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
79 | l_log(L_LOG_DEBUG, "%s:%s() " format, __FILE__, \
| ^~~~~~~~~~
../../ell/log.h:54:16: note: in definition of macro ‘l_log’
54 | __func__, format "\n", ##__VA_ARGS__)
| ^~~~~~
../../ell/log.h:103:31: note: in expansion of macro ‘L_DEBUG_SYMBOL’
103 | #define l_debug(format, ...) L_DEBUG_SYMBOL(__debug_desc, format, ##__VA_ARGS__)
| ^~~~~~~~~~~~~~
../../src/dpp.c:1235:3: note: in expansion of macro ‘l_debug’
1235 | l_debug("I-Nonce has unexpected length %lu", i_nonce_len);
| ^~~~~~~
Direct leak of 64 byte(s) in 1 object(s) allocated from:
#0 0x7fa226fbf0f8 in __interceptor_malloc (/usr/lib/gcc/x86_64-pc-linux-gnu/9.4.0/libasan.so.5+0x10c0f8)
#1 0x688c98 in l_malloc ell/util.c:62
#2 0x6c2b19 in msg_alloc ell/genl.c:740
#3 0x6cb32c in l_genl_msg_new_sized ell/genl.c:1567
#4 0x424f57 in netdev_build_cmd_authenticate src/netdev.c:3285
#5 0x425b50 in netdev_sae_tx_authenticate src/netdev.c:3385
Direct leak of 7 byte(s) in 1 object(s) allocated from:
#0 0x7fd748ad00f8 in __interceptor_malloc (/usr/lib/gcc/x86_64-pc-linux-gnu/9.4.0/libasan.so.5+0x10c0f8)
#1 0x688c21 in l_malloc ell/util.c:62
#2 0x4beec7 in handshake_state_set_vendor_ies src/handshake.c:324
#3 0x464e4e in station_handshake_setup src/station.c:1203
#4 0x472a2f in __station_connect_network src/station.c:2975
#5 0x473a30 in station_connect_network src/station.c:3078
#6 0x4ed728 in network_connect_8021x src/network.c:1497
Fixes: f24cfa481b ("handshake: Add setter for vendor IEs")
This implements a configurator in the responder role. Currently
configuring an enrollee is limited to only the connected network.
This is to avoid the need to go offchannel for any reason. But
because of this a roam, channel switch, or disconnect will cause
the configuration to fail as none of the frames are being sent
offchannel.
Added both enrollee and configurator roles, as well as the needed
logic inside the authentication protocol to verify role compatibility.
The dpp_sm's role will now be used when setting capability bits making
the auth protocol agnostic to enrollees or configurators.
This also allows the card to re-issue ROC if it ends in the middle of
authenticating or configuring as well as add a maximum timeout for
auth/config protocols.
IO errors were also handled as these sometimes can happen with
certain drivers but are not fatal.
Allows creating a new configuration object based on settings, ssid,
and akm suite (for configurator role) as well as converting a
configuration object to JSON.
Rather than hard coding ad0, use the actual frame data. There really
isn't a reason this would differ (only status attribute) but just
in case its better to use the frame data directly.
This is a minimal implementation only supporting legacy network
configuration, i.e. only SSID and PSK/passphrase are supported.
Missing features include:
- Fragmentation/comeback delay support
- DPP AKM support
- 8021x/PKEX support
This implements the DPP protocol used to authenticate to a
DPP configurator.
Note this is not a full implementation of the protocol and
there are a few missing features which will be added as
needed:
- Mutual authentication (needed for BLE bootstrapping)
- Configurator support
- Initiator role
The presence procedure implemented is a far cry from what the spec
actually wants. There are two reason for this: a) the kernels offchannel
support is not at a level where it will work without rather annoying
work arounds, and b) doing the procedure outlined in the spec will
result in terrible discovery performance.
Because of this a simpler single channel announcement is done by default
and the full presence procedure is left out until/if it is needed.
This is a minimal wrapper around jsmn.h to make things a bit easier
for iterating through a JSON object.
To use, first parse the JSON and create a contents object using
json_contents_new(). This object can then be used to initialize a
json_iter object using json_iter_init().
The json_iter object can then be parsed with json_iter_parse by
passing in JSON_MANDATORY/JSON_OPTIONAL arguments. Currently only
JSON_STRING and JSON_OBJECT types are supported. Any JSON_MANDATORY
values that are not found will result in an error.
If a JSON_OPTIONAL string is not found, the pointer will be NULL.
If a JSON_OPTIONAL object is not found, this iterator will be
initialized but 'start' will be -1. This can be checked with a
convenience macro json_object_not_found();
Static analysis was not happy since this return can be negative and
it was being fed into an unsigned argument. In reality this cannot
happen since the key buffer is always set to the maximum size supported
by any curves.
This module provides a convenient wrapper around both
CMD_[CANCEL_]_REMAIN_ON_CHANNEL APIs.
Certain protocols require going offchannel to send frames, and/or
wait for a response. The frame-xchg module somewhat does this but
has some limitations. For example you cannot just go offchannel;
an initial frame must be sent out to start the procedure. In addition
frame-xchg does not work for broadcasts since it expects an ACK.
This module is much simpler and only handles going offchannel for
a duration. During this time frames may be sent or received. After
the duration the caller will get a callback and any included error
if there was one. Any offchannel request can be cancelled prior to
the duration expriring if the offchannel work has finished early.
The disconnect event handler was mistakenly bailing out if FT or
reassociation was going on. This was done because a disconnect
event is sent by the kernel when CMD_AUTH/CMD_ASSOC is used.
The problem is an AP could also disconnect IWD which should never
be ignored.
To fix this always parse the disconnect event and, if issued by
the AP, always notify watchers of the disconnect.
LLD 13 and GNU ld 2.37 support -z start-stop-gc which allows garbage
collection of C identifier name sections despite the __start_/__stop_
references. GNU ld before 2015-10 had the behavior as well. Simply set
the retain attribute so that GCC 11 (if configure-time binutils is 2.36
or newer)/Clang 13 will set the SHF_GNU_RETAIN section attribute to
prevent garbage collection.
Without the patch, there are linker errors with -z start-stop-gc
(LLD default) when -Wl,--gc-sections is used:
```
ld.lld: error: undefined symbol: __start___eap
>>> referenced by eap.c
>>> src/eap.o:(eap_init)
```
The remain attribute will not be needed if the metadata sections are
referenced by code directly.
ap.c has been mostly careful to call the event handler at the end of any
externally called function to allow methods like ap_free() to be called
within the handler, but that isn't enough. For example in
ap_del_station we may end up emitting two events: STATION_REMOVED and
DHCP_LEASE_EXPIRED. Use a slightly more complicated mechanism to
explicitly guard ap_free calls inside the event handler.
To make it easier, simplify cleanup in ap_assoc_reassoc with the use of
_auto_.
In ap_del_station reorder the actions to send the STATION_REMOVED event
first as the DHCP_LEASE_EXPIRED is a consequence of the former and it
makes sense for the handler to react to it first.
src/eap.c: In function 'eap_rx_packet':
src/eap.c:419:50: error: 'vendor_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
419 | (type == EAP_TYPE_EXPANDED && vendor_id == (id) && vendor_type == (t))
| ^~
src/eap.c:430:11: note: 'vendor_type' was declared here
430 | uint32_t vendor_type;
It isn't clear why GCC complains about vendor_type, but not vendor_id.
But in all cases if type == EAP_TYPE_EXPANDED, then vendor_type and
vendor_id are set. Silence this spurious warning.
There is an unchecked NULL pointer access in network_has_open_pair.
open_info can be NULL, when out of multiple APs in range that advertise
the same SSID some advertise OWE transition elments and some don't.
The Hotspot 2.0 spec has some requirements that IWD was missing depending
on a few bits in extended capabilities and the HS2.0 indication element.
These requirements correspond to a few sysfs options that can be set in
the kernel which are now set on CONNECTED and unset on DISCONNECTED.
Netconfig was the only user of sysfs but now other modules will
also need it.
Adding existing API for IPv6 settings, a IPv4 and IPv6 'supports'
checker, and a setter for IPv4 settings.
The way a SA Query was done following a channel switch was slightly
incorrect. One because it is only needed when OCVC is set, and two
because IWD was not waiting a random delay between 0 and 5000us as
lined out by the spec. This patch fixes both these issues.
Cache the latest v4 and v6 domain string lists in struct netconfig state
to be able to more easily detect changes in those values in future
commits. For that split netconfig_set_domains's code into this function,
which now only commits the values in netconfig->v{4,6}_domain{,s} to the
resolver, and netconfig_domains_update() which figures out the active
domains string list and saves it into netconfig->v{4,6}_domain{,s}. This
probably saves some cycles as the callers can now decide to only
recalculate the domains list which may have changed.
While there simplify netconfig_set_domains return type to void as the
result was always 0 anyway and was never checked by callers.
Cache the latest v4 and v6 DNS IP string lists in struct netconfig state
to be able to more easily detect changes in those values in future
commits. For that split netconfig_set_dns's code into this function,
which now only commit the values in netconfig->dns{4,6}_list to the
resolver, and netconfig_dns_list_update() which figures out the active
DNS IP address list and saves it in netconfig->dns{4,6} list. This
probably saves some cycles as the callers can now decide to only
recalculate the dns_list which may have changed.
While there simplify netconfig_set_dns return type to void as the result
was always 0 anyway and was never checked by callers.
Cache the latest v4 and v6 gateway IP string in struct netconfig state
to be able to more easily detect changes in those values in future
commits and perhaps to simplify the ..._routes_install functions.
netconfig_ipv4_get_gateway's out_mac parameter can now be NULL. While
editing that function fix a small formatting annoyance.
Use a separate fils variable to make the code a bit prettier.
Also make sure that the out_mac parameter is not NULL prior to storing
the gateway_mac in it.
Add netconfig_enabled() and use that in all places that want to know
whether network configuration is enabled. Drop the enable_network_config
deprecated setting, which was only being handled in one of these 5 or so
places.
This code path was never tested and used to ensure a OWE transition
candidate gets selected over an open one (e.g. if all the BSS's are
blacklisted). But this logic was incorrect and the path was being
taken for BSS's that did not contain the owe_trans element, basically
all BSS's. For RSN's this was somewhat fine since the final check
would set a candidate, but for open BSS's the loop would start over
and potentially complete the loop without ever returning a candidate.
If fallback was false, NULL would be returned.
To fix this only take the OWE transition path if its an OWE transition
BSS, i.e. inverse the logic.
Normally Beacon Reporting subelements are present only if repeated
measurements are requested. However, an all-zero Beacon Reporting
subelement is included by some implementations. Handle this case
similarly to the absent case.
Since Reporting Detail subelement is listed as 'extensible', make sure
that the length check is not overly restrictive. We only interpret the
first field.
It was seen during testing that several offload-capable cards
were not including the OCI in the 4-way handshake. This made
any OCV capable AP unconnectable.
To be safe disable OCV on any cards that support offloading.
802.11 requires an STA initiate the SA Query procedure on channel
switch events. This patch refactors sending the SA Query into its
own routine and starts the procedure when the channel switch event
comes in.
In addition the OCI needs to be verified, so the channel info is
parsed and set into the handshakes chandef.
There are several events for channel switching, and nl80211cmd was
naming two of them "Channel Switch Notify". Change
CH_SWITCH_STARTED_NOTIFY to "Channel Switch Started Notify" to
distinguish the two events.
SA query is the final protocol that requires OCI inclusion and
verification. The OCI element is now included and verified in
both request and response frames as required by 802.11.
strcmp behavior is undefined if one of the parameters is NULL.
Server-id is a mandatory value and cannot be NULL. Gateway can be NULL
in DHCP, so check that explicitly.
Reported-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
In certain situations, it is possible for us to know the MAC of the
default gateway when DHCP finishes. This is quite typical on many home
network and small network setups. It is thus possible to pre-populate
the ARP cache with the gateway MAC address to save an extra round trip
at connection time.
Another advantage is during roaming. After version 4.20, linux kernel
flushes ARP caches by default whenever netdev encounters a no carrier
condition (as is the case during roaming). This can prevent packets
from going out after a roam for a significant amount of time due to
lost/delayed ARP responses.
This implements the new handshake callback for setting a TK with
an extended key ID. The procedure is different from legacy zero
index TKs.
First the new TK is set as RX only. Then message 4 should be sent
out (so it uses the existing TK). This poses a slight issue with
PAE sockets since message order is not guaranteed. In this case
the 4th message is stored and sent after the new TK is installed.
Then the new TK is modified using SET_KEY to both send and
receive.
In the case of control port over NL80211 the above can be avoided
and we can simply install the new key, send message 4, and modify
the TK as TX + RX all in sequence, without waiting for any callbacks.
When UseDefaultInterface is set, iwd doesn't attempt to destroy and
recreate any default interfaces it detects. However, only a single
default interface was ever remembered & initialized. This is fine for
most cases since the kernel would typically only create a single netdev
by default.
However, some drivers can create multiple netdevs by default, if
configured to do so. Other usecases, such as tethering, can also
benefit if iwd initialized & managed all default netdevs that were
detected at iwd start time or device hotplug.
oci variable is always set during handshake_util_find_kde. Do not
initialize it unnecessarily to help the compiler / static analysis find
potential issues.
If OCI is not used, then the oci array is never initialized. Do not try
to include it in our GTK 2_of_2 message.
Fixes: ad4d639854 ("eapol: include OCI in GTK 2/2")
802.11 added Extended Key IDs which aim to solve the issue of PTK
key replacement during rekeys. Since swapping out the existing PTK
may result in data loss because there may be in flight packets still
using the old PTK.
Extended Key IDs use two key IDs for the PTK, which toggle between
0 and 1. During a rekey a new PTK is derived which uses the key ID
not already taken by the existing PTK. This new PTK is added as RX
only, then message 4/4 is sent. This ensure message 4 is encrypted
using the previous PTK. Once sent, the new PTK can be modified to
both RX and TX and the rekey is complete.
To handle this in eapol the extended key ID KDE is parsed which
gives us the new PTK key index. Using the new handshake callback
(handshake_state_set_ext_tk) the new TK is installed. The 4th
message is also included as an argument which is taken care of by
netdev (in case waiting for NEW_KEY is required due to PAE socekts).
This may not be required but setting the group key mode explicitly
to multicast makes things consistent, even if only for the benefit
of reading iwmon logs easier.
The procedure for setting extended key IDs is different from the
single PTK key. The key ID is toggled between 0 and 1 and the new
key is set as RX only, then set to RX/TX after message 4/4 goes
out.
Since netdev needs to set this new key before sending message 4,
eapol can include a built message which netdev will store if
required (i.e. using PAE).
ext_key_id_capable indicates the handshake has set the capability bit
in the RSN info. This will only be set if the AP also has the capability
set.
active_tk_index is the key index the AP chose in message 3. This is
now used for both legacy (always zero) and extended key IDs.
Move the reading of ControlPortOverNL80211 into wiphy itself and
renamed wiphy_control_port_capable to wiphy_control_port_enabled.
This makes things easier for any modules interested in control
port support since they will only have to check this one API rather
than read the settings and check capability.
Expose the Device Address property for each peer. The spec doesn't say
much about how permanent the address or the name are, although the
device address by definition lives longer than the interface addresses.
However the device address is defined to be unique and the name is not
so the address can be used to differentiate devices with identical name.
Being unique also may imply that it's assigned globally and thus
permanent.
Network Manager uses the P2P device address when saving connection
profiles (and will need it from the backend) and in this case it seems
better justified than using the name.
The address is already in the object path but the object path also
includes the local phy index which may change for no reason even when
the peer's address hasn't changed so the path is not useful for
remembering which device we've connected to before. Looking at only
parts of the path is considered wrong.
Some drivers might not actually support control port properly even if
advertised by mac80211. Introduce a new method to wiphy that will take
care of looking up any driver quirks that override the presence of
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211
Make consecutive calls to netconfig_load_settings() memory-leak safe by
introducing a netconfig_free_settings convenience method. This method
will free any settings that are allocated as a result of
netconfig_load_settings() and will be called from netconfig_free() to
ensure that any settings are freed as a result of netconfig_destroy().
For symmetry with IPv4, save the command id for this netlink command so
we can later add logic to the callback as well as be able to cancel the
command. No functional change in this commit alone.
FT/FILS handle their own PMK derivation but rekeys still require
using the 4-way handshake. There is some ambiguity in the spec whether
or not the PMKID needs to be included in message 1/4 and it appears
that when rekeying after FT/FILS hostapd does not include a PMKID.
The handshake contains the current BSS's RSNE/WPA which may differ
from the FT-over-DS target. When verifying the target BSS's RSNE/WPA
IE needs to be checked, not the current BSS.
If the deauth path was triggered IWD would deauth but end up
calling the connect callback with whatever result netdev had
set, e.g. 'NETDEV_RESULT_OK'. This, of course, caused station
some confusion.
FT-over-DS cannot use OCV due to how the kernel works. This means
we could connect initially with OCVC set, but a FT-over-DS attempt
needs to unset OCVC. Set OCVC false when rebuilding the RSNE for
reassociation.
The FT-over-DS action stage builds an FT-Request which contains an
RSNE. Since FT-over-DS will not support OCV add a boolean to
ft_build_authenticate_ies so the OCVC bit can be disabled rather
than relying on the handshake setting.
This modifies the FT logic to fist call get_oci() before
reassociation. This allows the OCI to be included in reassociation
and in the 4-way handshake later on.
The code path for getting the OCI had to be slightly changed to
handle an OCI that is already set. First the handshake chandef is
NULL'ed out for any new connection. This prevents a stale OCI from
being used. Then some checks were added for this case in
netdev_connect_event and if chandef is already set, start the 4-way
handshake.
netconfig_load_settings is called when establishing a new initial
association to a network. This function tries to update dhcp/dhcpv6
clients with the MAC address of the netdev being used. However, it is
too early to update the MAC here since netdev might need to powercycle
the underlying network device in order to update the MAC (i.e. when
AddressRandomization="network" is used).
If the MAC is set incorrectly, DHCP clients are unable to obtain the
lease properly and station is stuck in "connecting" mode indefinitely.
Fix this by delaying MAC address update until netconfig_configure() is
invoked.
Fixes: ad228461ab ("netconfig: Move loading settings to new method, refactor")
If the AP advertises FT-over-DS support it likely wants us to use
it. Additionally signal_low is probably going to be true since IWD
has started a roam attempt.
When netdev goes down so does station, but prior to netdev calling
the neighbor report callback. The way the logic was written station
is dereferenced prior to checking for any errors, causing a use
after free.
Since -ENODEV is used in this case check for that early before
accessing station.
This adds a utility to convert a chandef obtained from the kernel into a
3 byte OCI element format containing the operating class, primary
channel and secondary channel center frequency index.
This changes scan_bss from using separate members for each
OWE transition element data type (ssid, ssid_len, and bssid)
to a structure that holds them all.
This is being done because OWE transition has option operating
class and channel bytes which will soon be parsed. This would
end up needing 5 separate members in scan_bss which is a bit
much for a single IE that needs to be parsed.
This makes checking the presense of the IE more convenient
as well since it can be done with a simple NULL pointer check
rather than having to l_memeqzero the BSSID.
These members are currently stored in scan_bss but with the
addition of operating class/band info this will become 5
separate members. This is a bit excessive to store in scan_bss
separately so instead this structure can hold everything related
to the OWE transition IE.
Add a utility for setting the OCI obtained from the hardware (prior to
handshake starting) as well as a utility to validate the OCI obtained
from the peer.
This adds a utility that can convert an operating class + channel
combination to a frequency. Operating class is assumed to be a global
operating class from 802.11 Appendix E4.
This information can be found in Operating Channel Information (OCI) IEs,
as well as OWE Transition Mode IEs.
Calling handshake_state_setup_own_ciphers from within
handshate_state_set_authenticator_ie was misleading. In all cases the
supplicant chooses the AKM. This worked since our AP code only ever
advertises a single AKM, but would not work in the general case.
Similarly, the supplicant would choose which authentication type to use
by either sending the WPA1 or WPA2 IE (or OSEN). Thus the setting of
the related variables in handshake_state_set_authenticator_ie was also
incorrect. In iwd, the supplicant_ie would be set after the
authenticator_ie, so these settings would be overwritten in most cases.
Refactor these two setters so that the supplicant's chosen rsn_info
would be used to drive the handshake.
reallocarray has been added to glibc relatively recently (version 2.26,
from 2017) and apparently not all users run new enough glibc. Moreover,
reallocarray is not available with uclibc-ng. So use realloc if
reallocarray is not available to avoid the following build failure
raised since commit 891b78e9e8:
/home/giuliobenetti/autobuild/run/instance-3/output-1/host/lib/gcc/xtensa-buildroot-linux-uclibc/10.3.0/../../../../xtensa-buildroot-linux-uclibc/bin/ld: src/sae.o: in function `sae_rx_authenticate':
sae.c:(.text+0xd74): undefined reference to `reallocarray'
Fixes:
- http://autobuild.buildroot.org/results/c6d3f86282c44645b4f1c61882dc63ccfc8eb35a
There isn't much control station has with how BSS's are inserted to
a network object. The rank algorithm makes that decision. Because of
this we could end up in a situation where the Open BSS is preferred
over the OWE transition BSS.
In attempt to better handle this any Open BSS in this type of network
will not be chosen unless its the only candidate (e.g. no other BSSs,
inability to connect with OWE, or an improperly configured network).
OWE Transition is described in the WiFi Alliance OWE Specification
version 1.1. The idea behind it is to support both legacy devices
without any concept of OWE as well as modern ones which support the
OWE protocol.
OWE is a somewhat special type of network. Where it advertises an
RSN element but is still "open". This apparently confuses older
devices so the OWE transition procedure was created.
The idea is simple: have two BSS's, one open, and one as a hidden
OWE network. Each network advertises a vendor IE which points to the
other. A device sees the open network and can connect (legacy) or
parse the IE, scan for the hidden OWE network, and connect to that
instead.
Care was taken to handle connections to hidden networks directly.
The policy is being set that any hidden network with the WFA OWE IE
is not connectable via ConnectHiddenNetwork(). These networks are
special, and can only be connected to via the network object for
the paired open network.
When scan results come in from any source (DBus, quick, autoconnect)
each BSS is checked for the OWE Transition IE. A few paths can be
taken here when the IE is found:
1. The BSS is open. The BSSID in the IE is checked against the
current scan results (excluding hidden networks). If a match is
found we should already have the hidden OWE BSS and nothing
else needs to be done (3).
2. The BSS is open. The BSSID in the IE is not found in the
current scan results, and the open network also has no OWE BSS
in it. This will be processed after scan results.
3. The BSS is not open and contains the OWE IE. This BSS will
automatically get added to the network object and nothing else
needs to be done.
After the scan results each network is checked for any non-paired
open BSS's. If found a scan is started for these BSS's per-network.
Once these scan results come in the network is notified.
From here network.c can detect that this is an OWE transition
network and connect to the OWE BSS rather than the open one.
Specifically OWE networks with multiple open/hidden BSS's are troublesome
to scan for with the current APIs. The scan parameters are limited to a
single SSID and even if that was changed we have the potential of hitting
the max SSID's per scan limit. In all, it puts the burden onto the caller
to sort out the SSIDs/frequencies to scan for.
Rather than requiring station to handle this a new scan API was added,
scan_owe_hidden() which takes a list of open BSS's and will automatically
scan for the SSIDs in the OWE transition IE for each.
It is slightly optimized to first check if all the hidden SSID's are the
same. This is the most likely case (e.g. single pair or single network)
and a single scan command can be used. Otherwise individual scan commands
are queued for each SSID/frequency combo.
handshake_util_ap_ie_matches() is used to make sure that the RSN element
received from the Authenticator during handshake / association response
is the same as the one advertised in Beacon/Probe Response frames. This
utility tries to bitwise compare the element first, and only if that
fails, compares RSN members individually.
For FT, bitwise comparison will always fail since the PMKID has to be
included by the Authenticator in any RSN IEs included in Authenticate
& Association Response frames.
Perform the bitwise comparison as an optimization only during processing
of eapol message 3/4. Also keep the parsed rsn information for future
use and to possibly avoid re-parsing it during later checks.
DBus scan is performed in several subsets. In certain corner-case
circumstances it would be possible for autoconnect to run after each
subset scan. Instead, trigger autoconnect only after the dbus scan
completes.
This also works around a condition where ANQP results could trigger
autoconnect too early.
Several invocations of station_set_scan_results() base the
'add_to_autoconnect' parameter on station_is_autoconnecting(). Simplify
the code by having station_set_scan_results() invoke that itself.
'add_to_autoconnect' now becomes an 'intent' parameter, specifying
whether autoconnect path should be invoked as a result of these scan
results or not when station is in an appropriate state. Rename
'add_to_autoconnect' parameter to make this clearer.
If the frequency of the bss is not in the list of frequencies for the
current scan, then this is a cached bss. It was likely already
processed for ANQP before, so skip it.
IWD has restricted SSIDs to only utf8 so they can be displayed but
with the addition of OWE transition networks this is an unneeded
restriction (for these networks). The SSID of an OWE transition
network is never displayed to the user so limiting to utf8 isn't
required.
Allow non-utf8 SSIDs to be scanned for by including the length in
the scan parameters and not relying on strlen().
This is a parser for the WFA OWE Transition element. For now the
optional band/channel bytes will not be parsed as hostapd does not
yet support these and would also require the 802.11 appendix E-1
to be added to IWD. Because of this OWE Transition networks are
assumed to be on the same channel as their open counterpart.
in6_addr.__in6_u.__u6_addr8 is glibc-specific and named differently in
the headers shipped with musl libc for example. The POSIX compliant and
universal way of accessing it is in6_addr.s6_addr.
This was actually broken if triggered because __network_connect
checks if network->connect_after_owe_hidden is set and returns
already in progress. We want to keep this behavior though for
obvious reasons.
To fix this station_connect_network can be called directly which
bypasses the check. This is essentially how ANQP avoids this
problem as well.
Similar to ANQP a connect call could come in while station is
scanning for OWE hidden networks. This is supported in the same
manor by saving away the dbus message and resuming the connection
after the hidden OWE scan.
With the addition of OWE transition network needs to be notified
of the hidden OWE scan which is quite similar to how it is notified
of ANQP. The ANQP event watch can be made generic and reused to
allow other events besides ANQP.
This is being added to support OWE transition mode. For these
type of networks the OWE BSS may contain a different SSID than
that of the network, but the WFA spec requires this be hidden
from the user. This means we need to set the handshake SSID based
on the BSS rather than the network object.
Refactor netconfig_set_dns to be a bit easier to follow and remove use
of macros. Also bail out early if no DNS addresses are provided instead
of building an empty DNS list since resolve_set_dns() simply returns if
a NULL or empty DNS list is provided.
Kernel keeps transmitting authentication frames until told to stop or an
authentication frame the kernel considers 'final' is received. Detect
cases where the kernel would keep retransmitting, and if auth_proto
encounters a fatal protocol error, prevent these retransmissions from
occuring by sending a Deauthenticate command to the kernel.
Additionally, treat -EBADMSG/-ENOMSG return from auth_proto specially.
These error codes are meant to convey that a frame should be silently
dropped and retransmissions should continue.
This works around a hostapd bug (described more in the TODO comment)
which is exposed because of the kernels overly agressive re-transmit
behavior on missed ACKs. Combined this results in a death if the
initial commit is not acked. This behavior has been identified in
consumer access points and likely won't ever be patched for older
devices. Because of this IWD must work around the problem which can
be eliminated by not sending out this commit message.
This bug was reported to the hostapd ML:
https://lists.infradead.org/pipermail/hostap/2021-September/039842.html
This change should not cause any compatibility problems to non-hostapd
access points and is identical to how wpa_supplicant treats this
scenario.
If a commit is received while in an accepted state the spec states
the scalar should be checked against the previous commit and if
equal the message should be silently dropped.
In netconfig_load_settings apply the DNS overrides strings we've loaded
instead of leaking them.
Fixes: ad228461ab ("netconfig: Move loading settings to new method, refactor")
netdev now assumes the SSID was set in the handshake (normally via
network_handshake_setup) but WSC calls netdev_connect directly so
it also should set the SSID.
In order to support OWE in the CMD_CONNECT path the scan_bss parameter
needs to be removed since this is lost after netdev_connect returns.
Nearly everything needed is also stored in the handshake except the
privacy capability which is now being mirrored in the netdev object
itself.
Use the MAC addresses for the gateways and DNS servers received in the
FILS IP Assigment IE together with the gateway IP and DNS server IP.
Commit the IP to MAC mappings directly to the ARP/NDP tables so that the
network stack can skip sending the corresponding queries over the air.
Send and receive the FILS IP Address Assignment IEs during association.
As implemented this would work independently of FILS although the only
AP software handling this mechanism without FILS is likely IWD itself.
No support is added for handling the IP assignment information sent from
the server after the initial Association Request/Response frames, i.e.
the information is only used if it is received directly in the
Association Response without the "response pending" bit, otherwise the
DHCP client will be started.
Add two methods that will allow station to implement FILS IP Address
Assigment, one method to decide whether to send the request during
association, and fill in the values to be used in the request IE, and
another to handle the response IE values received from the server and
apply them. The netconfig->rtm_protocol value used when the address is
assigned this way remains RTPROT_DHCP because from the user's point of
view this is automatic IP assigment by the server, a replacement for
DHCP.
Split loading settings out of network_configure into a new method,
network_load_settings. Make sure both consistently handle errors by
printing messages and informing the caller.
Setter which forces the use of group 19 rather than the group order
that ELL provides. Certain APs have been found to have buggy group
negotiation and only work if group 19 is tried first, and only. When
an AP like this this is found (based on vendor OUI match) SAE will
use group 19 unconditionally, and fail if group 19 does not work.
Other groups could be tried upon failure but per the spec group 19
must be supported so there isn't much use in trying other, optional
groups.
Handle the 802.11ai FILS IP Address Assignment IEs in Association
Request frames when netconfig is enabled. Only IPv4 is supported.
Like the P2P IP Allocation mechanism, since the payload format and logic
is independent from the rest of the FILS standard this is enabled
unconditionally for clients who want to use it even though we don't
actually do FILS in AP mode.
If netconfig is enabled tell the DHCP server to expire any leases owned
by the client that is disconnecting by using l_dhcp_server_expire_by_mac
to return the IPs to the IP pool. They're added to the expired list
so they'd only be used if there are no other addresses left in the pool
and can be reactivated if the client comes back before the address is
used by somebody else.
This should ensure that we're always able to offer an address to a new
client as long as there are fewer concurrent clients than addresses in
the configured subnet or IP range.
Use the struct handshake_state::support_ip_allocation field already
supported in eapol.c authenticator side to enable the P2P IP Allocation
mechanism in ap.c. Add the P2P_GROUP_CAP_IP_ALLOCATION bit in P2P group
capabilities to signal the feature is now supported.
There's no harm in enabling this feature in every AP (not just P2P Group
Owner) but the clients won't know whether we support it other than
through that P2P-specific group capability bit.
Add a handshake event for use by the AP side for mechanisms that
allocate client IPs during the handshake: P2P address allocation and
FILS address assignment. This is emitted only when EAPOL or the
auth_proto is actually about to send the network configuration data to
the client so that ap.c can skip allocating a DHCP leases altogether if
the client doesn't send the required KDE or IE.
Some drivers ignore the initial IF_OPER_UP setting that was sent during
netdev_connect_ok(). Attempt to work around this by parsing New Link
events. If OperState setting is still not correct in a subsequent event,
retry setting OperState to IF_OPER_UP.
The hotspot case can actually result in network being NULL which
ends up crashing when accessing "->secrets". In addition any
secrets on this network were never removed for hotspot networks
since everything happened in network_unset_hotspot.
This is meant to be used as a generic notification to autotests. For
now 'no-roam-candidates' is the only event being sent. The idea
is to extend these events to signal conditions that are otherwise
undiscoverable in autotesting.
Replace instances of the ap_del_station() +
ap_sta_free()/ap_remove_sta() with calls to ap_station_disconnect to
make sure we consistently remove the station from the ap->sta_states
queue before using ap_del_station(). ap_del_station() may generate an
event to the ap.h API user (e.g. P2P) and this may end up tearing down
the AP completely.
For that scenario we also don't want ap_sta_free() to access sta->ap so
we make sure ap_del_station() performs these cleanup steps so that
ap_sta_free() has nothing to do that accesses sta->ap.
client_frame is not valid for a beacon frame as beacons are not sent in
response to another frame. Move the access to client_frame->address_2
to the conditional blocks for Probe Response and Association Response
frames.
This is to support the autotesting framework by allowing a smaller
scan subset. This will cut down on the amount of time spent scanning
via normal DBus scans (where the entire spectrum is scanned).
Most autotests do not want autoconnect behavior so it is being
turned off by default. There are a few tests where it is needed
and in these few cases the test can enable autoconnect through
the new station debug property.
This adds the property "AutoConnect" to the station debug interface
which can be read/written to disable or enable autoconnect globally.
As one would expect this property is only going to be used for testing
hence why it was put on the debug interface. Mosts tests disable
autoconnect (or they should) because it leads to unexpected connections.
This method will initiate a connection to a specific BSS rather
than relying on a network based connection (which the user has
no control over which specific BSS is selected).
The only point of failure in netdev_connect_common was setting
up the handshake type. Moving this outside of netdev_connect_common
makes the code flow much better in netdev_{connect,reassociate} as
nothing needs to be reset upon failure.
Utilize 'storage_is_file' when readdir returns DT_UNKNOWN to ensure
features like autoconnect work on filesystems that don't return a d_type
(eg. XFS).
Utilize 'storage_is_file' when readdir returns DT_UNKNOWN to ensure
features like autoconnect work on filesystems that don't return a d_type
(eg. XFS).
Add a function 'storage_is_file' which will use stat to verify a
file's existence given a path relative to the storage directory.
Not all filesystems provide a file type via readdir's d_type.
XFS is a notable system with optional d_type support.
When d_type is not supported stat must be used as a fallback.
If a stat fallback is not provided iwd will fail to load state files.
The preparing_roam flag is expected to be set by a few roam
routines and normally this is done prior to the roam scan.
The Roam() developer option was not doing this and would
cause failed roams in some cases.
This adds support in netdev_reassociate for all the auth
protocols (SAE/FILS/OWE) by moving the bulk of netdev_connect
into netdev_connect_common. In addition PREV_BSSID is set
in the associate message if 'in_reassoc' is true.
Some connections, like Hotspot require additional IEs to be used during
the Association. These are now passed as 'extra_ies' when invoking
netdev_connect, however they are also needed during ReAssociation and FT
to such APs.
Additionally, it may be that Hotspot-enabled APs will start utilizing
FILS or SAE. In these cases the extra_ies need to be accounted for
somehow, either by making a copy in handshake_state, netdev, or the
auth_proto itself. Similarly, P2P which heavily uses vendor IEs can be
used over SAE in the future.
Since a copy of these IEs is needed, might as well store them in
handshake_state itself for easy book-keeping by network/station.
RM Enabled Capabilities and Extended Capabilities IEs were correctly
being sent when using CMD_CONNECT for initial connections and
re-associations. However, for SoftMac SAE, FT, FILS and OWE connections,
these additional IEs were not added properly during the Associate step.
If the driver supports RRM, then we might as well always send the RM
Enabled Capabilities IE (and use the USE_RRM flag). 802.11-2020
suggests that this IE can be sent whenever
dot11RadioMeasurementActivated is true, and this setting is independent
of whether the peer supports RRM. There's nothing to indicate that an
STA should not send these IEs if the AP is not RRM enabled.
While we correctly emit a NETDEV_EVENT_CHANNEL_SWITCHED event from
netdev for other modules to respond to, we fail to actually update the
frequency of the netdev object in question. Since the netdev frequency
is used elsewhere (e.g. to send action frames), it needs updating too.
Fixes: 5eb0b7ca8e ("netdev: add a channel switch event")
This variable ended up being used only on the fast-transition path. On
the re-associate path it was never used, but memcpy-ied nevertheless.
Since its only use is by auth_proto based protocols, move it to the
auth_proto object directly.
Due to how prepare_ft works (we need prev_bssid from the handshake, but
the handshake is reset), have netdev_ft_* methods take an 'orig_bss'
parameter, similar to netdev_reassociate.
IE elements in various management frames are ordered. This ordering is
outlined in 802.11, Section 9.3.3. The ordering is actually different
depending on the frame type. Instead of trying to implement the order
manually, add a utility function that will sort the IEs in the order
expected by the particular management frame type.
Since we already have IE ordering look up tables in the various
management frame type validation functions, move them to global level
and re-use these lookup tables for the sorting utility.
This refactors some code to eliminate getting the ERP entry twice
by simply returning it from network_has_erp_identity (now renamed
to network_get_erp_cache). In addition this code was moved into
station_build_handshake_rsn and properly cleaned up in case there
was an error or if a FILS AKM was not chosen.
The authorized macs pointer was being set to either the wsc_beacon
or wsc_probe_response structures, which were initialized out of
scope to where 'amacs' was being used. This resulted in an out of
scope read, caught by address sanitizers.
One of these message buffers was overflowing due to padding not
being taken into account (caught by sanitizers). Wrapped the length
of all message buffers with EAP_SIM_ROUND as to account for any
padding that attributes may add.
The network_config was not being copied to network_info when
updated. This caused any new settings to be lost if the network
configuration file was updated during runtime.
The RoamThreshold5G was never honored because it was being
set prior to any connections. This caused the logic inside
netdev_cqm_rssi_update to always choose the 2GHz threshold
(RoamThreshold) due to netdev->frequency being zero at this time.
Instead call netdev_cqm_rssi_update in all connect/transition
calls after netdev->frequency is updated. This will allow both
the 2G and 5G thresholds to be used depending on what frequency
the new BSS is.
The call to netdev_cqm_rssi_update in netdev_setup_interface
was also removed since it serves no purpose, at least now
that there are two thresholds to consider.
Under certain conditions, access points with very low signal could be
detected. This signal is too low to estimate a data rate and causes
this L_WARN to fire. Fix this by returning a -ENETUNREACH error code in
case the signal is too low for any of the supported rates.
Transition Disable indications and information stored in the network
profile needs to be enforced. Since Transition Disable information is
now stored inside the network object, add a new method
'network_can_connect_bss' that will take this information into account.
wiphy_can_connect method is thus deprecated and removed.
Transition Disable can also result in certain AKMs and pairwise ciphers
being disabled, so wiphy_select_akm method's signature is changed and
takes the (possibly overriden) ie_rsn_info as input.
This indication can come in via EAPoL message 3 or during
FILS Association. It carries information as to whether certain
transition mode options should be disabled. See WPA3 Specification,
version 3 for more details.
Some network settings keys are set / parsed in multiple files. Add a
utility to parse all common network configuration settings in one place.
Also add some defines to make sure settings are always saved in the
expected group/key.
