The kernel allows a scan duration and duration mandatory flag to be
set in scan requests. RRM requests can contain these values so they
have been added to scan_parameters.
Scanning with drivers which do not support EXT_FEATURE_SET_SCAN_DWELL
will not include these values in scan requests.
no_cck_rates is set in the scan parameters generally to make sure
that the Probe Request frames are not sent at any of the 802.11b
rates during active scans. With this patch we also omit those rates
from the Supported Rates IEs, which is required by the p2p spec and
also matches our flag's name.
The intent here was to validate that the frequency is a multiple of 5
and lies in a certain range. Somehow the channel was checked for being
a multiple of 5 instead.
This will be seen in Probe Requests. More IEs can and should
be added here depending on the support in IWD. E.g. HS20 indication,
Interworking, HT/VHT IE's etc.
For (Re)Association the HS20 indication element was passed exactly as
it was found in the scan results. The spec defines what bits can be
set and what cannot when this IE is used in (Re)Association. Instead
of assuming the AP's IE conforms to the spec, we now parse the IE and
re-build it for use with (Re)Association.
Since the full IE is no longer used, it was removed from scan_bss, and
replaced with a bit for HS20 support (hs20_capable). This member is
now used the same as hs20_ie was.
The version parsed during scan results is now used when building the
(Re)Association IE.
The HS20 indication element should always be included during
(Re)Association per the spec. This removes the need for a
dedicated boolean, and now the hs20_ie can be used instead.
If the scan was triggered and later aborted, make sure to reset the
triggered value when the CMD_NEW_SCAN_RESULTS event comes in.
src/station.c:station_enter_state() Old State: disconnected, new state: connecting
src/scan.c:scan_notify() Scan notification 33
src/station.c:station_netdev_event() Associating
src/scan.c:scan_notify() Scan notification 34
Aborting (signal 11) [/home/denkenz/iwd-master/src/iwd]
++++++++ backtrace ++++++++
#0 0x7efd4d6a2ef0 in /lib64/libc.so.6
#1 0x42b20d in scan_notify() at src/scan.c:1383
P2P probe requests are to be sent at min 6.0 Mb/s using OFDM,
specifically the 802.11b rates are prohibited (section 2.4.1 in Wi-Fi
P2p Technical Spec v1.7), some of which use CCK modulation. This is
already the default for 5G but for 2.4G the drivers generally do this
if we set the NL80211_ATTR_TX_NO_CCK_RATE flags with
NL80211_CMD_TRIGGER_SCAN.
The ifindex is used to index the netdevs in the system (wlan, ethernet,
etc.) but we can also do wifi scanning on interfaces that have no
corresponding netdev object, like the P2P-device virtual interfaces.
Use the wdev id's to reference interfaces, the nl80211 api doesn't care
whether we use a NL80211_ATTR_IFINDEX or NL80211_ATTR_WDEV. Only
wireless interfaces have a wdev id.
Save the actual cmd_id returned from l_genl_family_dump and zero it in
the get_scan_done. There's no need to zero it in scan_cancel because
get_scan_done gets called automatically.
Store the scan_context pointer in scan_results directly instead of
storing the ifindex. We now cancel ongoing GET_SCAN commands when the
scan_context is being freed so there's no point going through the extra
step of looking up the scan_context by ifindex inside the command
callback to guard against non-existent scan_contexts.
In order to do ANQP efficiently IWD needs the ability to suspend scanning
temporarily. This is because both scanning and ANQP go offchannel and must
remain off channel for some amount of time. This cannot be done
simultaneously and if e.g. ANQP is requested after a scan is already
pending, the kernel will wait till that scan finishes before sending out
the frame.
This IE tells us what Advertisement Protocols the AP supports. This
is only here to look for ANQP support, so all this does is iterate
through all other Advertisement Protocol tuples looking for ANQP.
If found, anqp_capable is set in the scan_bss
The vendor specific IE was being parsed only to check if the AP supported
WPA, which used a Microsoft OUI. Hotspot/OSEN uses neither WPA or RSN
(although its nearly identical to RSN) so the we also need to check for
this Wifi-Alliance OUI and set bss->osen (new) if found.
When handling a scan finished event for a scan we haven't started check
that we were not halfway through a scan request that would have its
results flushed by the external scan.
Instead of having two separate types of scans make the periodic scan
logic a layer on top of the one-off scan requests, with minimum code to
account for the lower priority of those scans and the fact that periodic
scans also receive results from external scans. Also try to simplify
the code for both the periodic and one-off scans. In the SCAN_RESULTS
and SCAN_ABORT add more complete checks of the current request's state
so we avoid some existing crashes related to external scans.
scan_send_next_cmd and start_next_scan_request are now just one function
since their funcionality was similar and start_next_scan_request is used
everywhere. Also the state after the trigger command receives an EBUSY
is now the same as when a new scan is on top of the queue so we have
fewer situations to consider.
This code still does not account for fragmented scans where an external
scan between two or our fragments flushes the results and we lose some
of the results, or for fragmented scans that take over 30s and the
kernel expires some results (both situations are unlikely.)
Previously, the scan results were disregarded once the new
ones were available. To enable the scan scenarios where the
new scan results are delivered in parts, we introduce a
concept of aging BSSs and will remove them based on
retention time.
CC src/scan.o
src/scan.c: In function ‘scan_bss_compute_rank’:
src/scan.c:1048:4: warning: this decimal constant is unsigned only in ISO C90
factor = factor * data_rate / 2340000000 +
