This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
These test cases depend on setting up the existing hostapd instance to a
set of known addresses, which might be different from what test-runner
sets. During this time, any scans might result in the old and the new
addresses used by hostapd to be found in the scan results.
Fix that by using start_iwd=0 which tells test_runner that the test
wants to start iwd itself. This delays starting iwd until after the
setUpClass routine has been called and hostapd configured properly.
Also use more sensible rssi values for the 'non-preferred' bss.
Otherwise, ranking BSSes by throughput can confuse the test logic
since both BSSes are ranked the same and either can be picked by
autoconnect.
The cls object is part of the unittest framework and its lifespan
is out of test-runner's control. Setting objects into the cls
object sometimes keeps those objects around longer than desired.
Its best to unset anything set in cls when the test is tore down.
Every single roaming test had one of two problems with watching the
state change between roaming --> connected. Either the test used
wait_for_object_condition to wait for 'connected' which could allow
other states in between. Or it simply used an assert. The assert
wouldn't allow other state changes, but at the cost of potentially
failing due to IWD not having made it to the 'connected' state yet.
Now we have wait_for_object_change which takes two conditions:
initial (from_str) and expected (to_str). This API will not allow
any other conditions except these, and will wait for the expected
condition before continuing. This allows roaming test to reliably
wait for the roaming --> connected state change.
After the test-runner re-write many tests were left with
stale options that are no longer used at all. These were
periodically getting removed as changes were made to
individual tests, but its apparent now that a tree wide
removal was needed.
Many tests waited on the network object 'connected' property after
issuing a Connect command. This is not correct as 'connected' is
set quite early in the connection process. The correct way of doing
this is waiting for the device state to change to connected.
This common code was replaced, hopefully putting to rest any random
failures that happen occasionally.
Slower systems may not be able to make some timeouts that tests
mandated. All timeouts were increased significantly to allow tests
to pass on slow systems.
The tests basically remained the same with a few minor changes.
The wiphy_map and in turn hostapd_map are no longer used. This
was already partially converted a long time ago when the 'config'
parameter was added to HostapdCLI. This patch fully converts all
autotests to use 'config' rather than looking up by interface.
Some test scripts were named 'test.py' which was fine before but
the new rewrite actually loads each python test as a module. The
name 'test' is too ambiguous and causes issues due to a native
python module with the same name. All of these files were
renamed to 'connection_test.py'.
This removes all the duplicated code where the interfaces are iterated
and the radio/hostapd instances are created. Instead the two new APIs
are used to get each instance, e.g.:
hapd = HostapdCLI(config='ssid.conf')
radio = hwsim.get_radio('radX')
Running autotests with native hardware will not work on tests which
depend on the hwsim python API (since hwsim will not be running).
For these tests, it will now be required that they specify:
needs_hwsim=1
This allows the test to be skipped when running with native hardware
rather than the test failing with a python exception.
In the tests that only want to iterate over the hostapd interfaces,
simplify the pattern of walking through the whole wiphy_map tree by
instead using the hostapd_map variable which is already filtered to only
contain hostapd interfaces.
At some point a stray ';' got added into an autotest in a section
of code that is heavily copy pasted. So in turn nearly all the autotests
have this stray ';' after list_devices (and a few in other places).
