With various versions of wpa_supplicant tested, after an IWD GO tears
the group down, the wpa_supplicant P2P client will not immediately
signal that the group has disappeared but will at least wait for the
lost beacon signal, wait some more and try reconnecting and all that
takes it 10s or a little longer. Possibly sending Deauthenticate frames
to clients first would improve this.
mac80211_hwsim has a funny quirk with multiple addresses in
radios. Some operations require address index zero, some index
one. And these addresses (possibly a result of how test-runner
initializes radios) sometimes get mixed up. For example scan
results may show a BSS address as 02:00:00:00:00:00, while the
next test run shows 42:00:00:00:00:00.
Ultimately, sending out frames requires the first nibble of the
address to be 0x4 so to handle both variants of addresses described
above hwsim.py was updated to always bitwise OR the first byte
with 0x40.
The idea of this test is valid but it is extremely timing dependent
which simply isn't testable on all machines. Removing this test
at least until this can be tested reliably.
testHotspot suffered from improper cleanup and if a single test failed
all subsequent tests would fail due to IWD still running since IWD()
was never cleaned up.
In addition the PSK agent and hwsim rules are now set onto the cls
object and removed in tearDownClass()
There are really no cases where a test wants to remove a single
rule. Most loop through and remove rules individually so this
is being added as a convenience.
Certain autotests coupled with slower test machines can result in lost
beacons and "Network not found" errors. In attempt to help with this
the test can just rescan (30 seconds max) until the network is found.
Remove EAP-SIM from the generic PEAP test case since skipping
(if ofono is not on system) would skip the entire test rather
than just the EAP-SIM portion.
This tests all EAP methods in their standard configuration. Any
corner cases requiring changes to main.conf or other hostapd
options are not included and will be left as stand alone tests.
This was done because nearly all EAP tests are identical except
the IWD provisioning file and hostapd EAP users fine. The IWD
provisioning file can be swapped out as needed for each individual
test without actually restarting IWD. And the EAP users file can
simply be written to include every possible EAP method that
is supported.
The destructor was trying to do more than the scope of a destructor
by trying to handle this single case of hostapd being restarted.
Instead we can simply pass a keyword argument 'reinit' to the
constructor to tell it to reinitialize everything. And as for killing
hostapd this can be done in ungraceful_restart itself rather than
trying to handle it in the destructor.
This (hopefully) will make this test pass better on slower machines.
In addition the mechanism of copying over separate main.conf files
was changed (rather than echo'ing the option into /tmp/main.conf)
This addresses the TODO where HostapdCLI was creating separate
objects each time HostapdCLI was called. This was worked around
by manually setting the important members but instead the class
can be re-worked to act as somewhat of a singleton, per-config
at least.
If there is no HostapdCLI instance for a given config one is
created and initialized. Subsequent HostapdCLI calls (for the
same config) will be returned the same object rather than a
new one.
The hotspot ANQP delay test was setting a global delay on all
packets which had some unintended consequences. At the time this
was the only way of simulating the test scenario but now hwsim
supports prefix matching so only the ANQP request/response will
be delayed.
This test was accessing the subprocess object and calling terminate
which ends up causing issues with test-runners own process cleanup.
Instead kill() should be used.
Hostapd sometimes has trouble with specifying additional BSSs in
a single config file, at least in the test-runner environment.
Since all the BSS's specified were identical instead the test was
reworked to only have a single BSS and each subtest can connect
in its own unique way.
This test took quite a while to execute (~2 minutes on my machine)
because there was simply no other way to test this scenario but
waiting. Now the no-roam-candidates condition can be waited for
rather than just sleeping for 20 seconds. Additionally the default
RoamRetryInterval was being used which is 60 seconds. Instead
main.conf can set this to 5 seconds and really cut down on the time
to wait.
Part of a comment was also removed due to being incorrect. Even
with neighbor reports IWD still must scan, its just that the
scan is more limited and, in theory, faster.
get_ordered_network() now scans automatically and has been updated
to use the StationDebug.Scan() API rather than doing a full
dbus scan (unless full_scan = True). The frequencies to be scanned
are picked automatically based on the current hostapd status
(hidden behind ctx.hostapd.get_frequency()).
This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
With the addition of connect_bssid/roam very few tests actually
require hwsim. Since hwsim can lead to problems with scan results
its best to have it off by default and have each test that needs
it explicitly turn it on.
Tests which previously turned it off have had that option removed.
Tests that do require hwsim still are vulnerable to scan result
problems, so for these tests beacon_int was added to the hostapd
config which seems to help with reliability somewhat.
There is a common block of code in nearly every test which is incorrect,
most likely a copy-paste from long ago. It goes something like:
wd.wait_for_object_condition(device, 'not obj.scanning')
device.scan()
wd.wait_for_object_condition(device, 'not obj.scanning')
network = device.get_ordered_network("ssid")
The problem here is that sometimes the scanning property does not get
updated fast enough before device.scan() returns, meaning get_ordered_network
comes up with nothing. Some tests pass scan_if_needed=True which 'fixes'
this but ends up re-scanning after the original scan finishes.
To put this to rest scan_if_needed is now defaulted to True, and no
explicit scan should be needed.
In addition the send_bss_transition call was updated to only send a
single BSS. By sending two BSS's IWD is left to pick whichever one
it wants which makes the test behavior undefined.
