Any test using assertTrue(hostapd.list_sta()) improperly has been
replaced with wait_for_event(). There were a few places where this
was actually ok (i.e. IWD is already connected) but most needed to
be changed since the check was just after IWD connected and hostapd's
list_sta() API may not return a fully updated list.
This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
Every single roaming test had one of two problems with watching the
state change between roaming --> connected. Either the test used
wait_for_object_condition to wait for 'connected' which could allow
other states in between. Or it simply used an assert. The assert
wouldn't allow other state changes, but at the cost of potentially
failing due to IWD not having made it to the 'connected' state yet.
Now we have wait_for_object_change which takes two conditions:
initial (from_str) and expected (to_str). This API will not allow
any other conditions except these, and will wait for the expected
condition before continuing. This allows roaming test to reliably
wait for the roaming --> connected state change.
After the test-runner re-write many tests were left with
stale options that are no longer used at all. These were
periodically getting removed as changes were made to
individual tests, but its apparent now that a tree wide
removal was needed.
Changed to wait for DeviceState instead of network object as well
as moved hwsim rules ahead of the IWD initializer to avoid IWD
scanning before the rules are fully in place.
Slower systems may not be able to make some timeouts that tests
mandated. All timeouts were increased significantly to allow tests
to pass on slow systems.
test-runner now supports interface name replacement inside hostapd
config files. Since a given test configuration doesn't know what
interface names there will be $ifaceN can be specified instead e.g.
rsn_preauth_interfaces=$iface0 $iface1
The $ifaceN values will be replace with actual interface names when
the test is started.
This patch also removes ctrl_interface inside the hostapd config
files as this is no longer required.
The tests basically remained the same with a few minor changes.
The wiphy_map and in turn hostapd_map are no longer used. This
was already partially converted a long time ago when the 'config'
parameter was added to HostapdCLI. This patch fully converts all
autotests to use 'config' rather than looking up by interface.
Some test scripts were named 'test.py' which was fine before but
the new rewrite actually loads each python test as a module. The
name 'test' is too ambiguous and causes issues due to a native
python module with the same name. All of these files were
renamed to 'connection_test.py'.
This removes all the duplicated code where the interfaces are iterated
and the radio/hostapd instances are created. Instead the two new APIs
are used to get each instance, e.g.:
hapd = HostapdCLI(config='ssid.conf')
radio = hwsim.get_radio('radX')
Running autotests with native hardware will not work on tests which
depend on the hwsim python API (since hwsim will not be running).
For these tests, it will now be required that they specify:
needs_hwsim=1
This allows the test to be skipped when running with native hardware
rather than the test failing with a python exception.
In the tests that only want to iterate over the hostapd interfaces,
simplify the pattern of walking through the whole wiphy_map tree by
instead using the hostapd_map variable which is already filtered to only
contain hostapd interfaces.
At some point a stray ';' got added into an autotest in a section
of code that is heavily copy pasted. So in turn nearly all the autotests
have this stray ';' after list_devices (and a few in other places).
Test that the AP interface and the station interface managed by iwd
can actually send and receive ethernet traffic when iwd is in the
connected state. Due to linux routing none of the high level utilities
like ping or arping can be easily used to test communication between
two interfaces of the same machine so use a method based on the
mac80211_hwsim/tools/hwsim_test.c utility in the wpa_supplicant tree
that uses a raw socket to inject unicast and broadcast frames.
Add this check in three tests of different security type connections
that simulate a single AP, and the two roaming tests with two APs.
Check that the station can't communicate with the other AP's interface.
Unfortunately this doesn't currently ensure that the preauthentication
has succeeded and that later the PMKSA from the preauthentication was
used in the transition, only that the preauthentication process doesn't
break the transition. For now this can be confirmed by looking at the
testrunner -v output to see that the line "EAP completed with eapSuccess"
appears before the following line, and not after:
src/device.c:device_enter_state() Old State: connected, new state: roaming
