mschaputil already had similar functionality, but ERP will need this
as well. These two functions will also handle identities with either
'@' or '\' to separate the user and domain.
Many operations performed during an error in load_settings were the same
as the ones performed when freeing the eap object. Add eap_free_common
to unify these.
EAP identites are recommended to follow RFC 4282 (The Network Access
Identifier). This RFC recommends a maximum NAI length of 253 octets.
It also mentions that RADIUS is only able to support NAIs of 253
octets.
Because of this, IWD should not allow EAP identities larger than 253
bytes. This change adds a check in eap_load_settings to verify the
identity does not exceed this limit.
The associate event is only important for OWE and FT. If neither of
these conditions (or FT initial association) are happening we do
not need to continue further processing the associate event.
802.11 mandates that IEs inside management frames are presented in a
given order. However, in the real world, many APs seem to ignore the
rules and send their IEs in seemingly arbitrary order, especially when
it comes to VENDOR tags. Change this function to no longer be strict in
enforcing the order.
Also, drop checking of rules specific to Probe Responses. These will
have to be handled separately (most likely by the AP module) since
802.11-2016, Section 11.1.4.3.5 essentially allows just about anything.
In netdev_associate_event the ignore_connect_event was getting set true,
but afterwards there were still potential failure paths. Now, once in
assoc_failed we explicitly set ignore_connect_event to false so the
the failure can be handled properly inside netdev_connect_event
The list of PSK/8021x AKM's in security_determine was getting long,
and difficult to keep under 80 characters. This moves them all into
two new macros, AKM_IS_PSK/AKM_IS_8021X.
It was assumed that the hunt-and-peck loop was guarenteed to find
a PWE. This was incorrect in terms of kernel support. If a system
does not have support for AF_ALG or runs out of file descriptors
the KDFs may fail. The loop continued to run if found == false,
which is also incorrect because we want to stop after 20 iterations
regarless of success.
This changes the loop to a for loop so it will always exit after
the set number of iterations.
CC src/scan.o
src/scan.c: In function ‘scan_bss_compute_rank’:
src/scan.c:1048:4: warning: this decimal constant is unsigned only in ISO C90
factor = factor * data_rate / 2340000000 +
The auto-connect state will now consist of the two phases:
STATION_STATE_AUTOCONNECT_QUICK and STATION_STATE_AUTOCONNECT_FULL.
The auto-connect will always start with STATION_STATE_AUTOCONNECT_QUICK
and then transition into STATION_STATE_AUTOCONNECT_FULL if no
connection has been established. During STATION_STATE_AUTOCONNECT_QUICK
phase we take advantage of the wireless scans with the limited number
of channels on which the known networks have been observed before.
This approach allows to shorten the time required for the network
sweeps, therefore decreases the connection latency if the connection
is possible. Thereafter, if no connection has been established after
the first phase we transition into STATION_STATE_AUTOCONNECT_FULL and
do the periodic scan just like we did before the split in
STATION_STATE_AUTOCONNECT state.
For simplicity 160Mhz and 80+80Mhz were grouped together when
parsing the VHT capabilities, but the 80+80 bits were left in
vht_widht_map. This could cause an overflow when getting the
width map.
wiphy_select_akm will now check if BIP is supported, and if MFPR is
set in the scan_bss before returning either SAE AKMs. This will allow
fallback to another PSK AKM (e.g. hybrid APs) if any of the requirements
are not met.
Replace existing uses of memset to clear secrets with explicit_bzero to
make sure it doesn't get optimized away. This has some side effects as
documented in gcc docs but is still recommended.
In eap_secret_info_free make sure we clear both strings in the case of
EAP_SECRET_REMOTE_USER_PASSWORD secrets.
Environments with several AP's, all at low signal strength may
want to lower the roaming RSSI threshold to prevent IWD from
roaming excessively. This adds an option 'roam_rssi_threshold',
which is still defaulted to -70.
Also printing keys with l_debug conditional on an environment variable
as someone wanting debug logs, or leaving debug on accidentally, does
not necessarily want the keys in the logs and in memory.
At some point the connect command builder was modified, and the
control port over NL80211 check was moved to inside if (is_rsn).
For WPS, no supplicant_ie was set, so CONTROL_PORT_OVER_NL80211
was never set into CMD_CONNECT. This caused IWD to expect WPS
frames over netlink, but the kernel was sending them over the
legacy route.
This commit hardens the iwd.service.in template file for systemd
services. The following is a short explanation for each added directive:
+PrivateTmp=true
If true, sets up a new file system namespace for the executed processes
and mounts private /tmp and /var/tmp directories inside it that is not
shared by processes outside of the namespace.
+NoNewPrivileges=true
If true, ensures that the service process and all its children can never
gain new privileges through execve() (e.g. via setuid or setgid bits, or
filesystem capabilities).
+PrivateDevices=true
If true, sets up a new /dev mount for the executed processes and only
adds API pseudo devices such as /dev/null, /dev/zero or /dev/random (as
well as the pseudo TTY subsystem) to it, but no physical devices such as
/dev/sda, system memory /dev/mem, system ports /dev/port and others.
+ProtectHome=yes
If true, the directories /home, /root and /run/user are made
inaccessible and empty for processes invoked by this unit.
+ProtectSystem=strict
If set to "strict" the entire file system hierarchy is mounted
read-only, except for the API file system subtrees /dev, /proc and /sys
(protect these directories using PrivateDevices=,
ProtectKernelTunables=, ProtectControlGroups=).
+ReadWritePaths=/var/lib/iwd/
Sets up a new file system namespace for executed processes. These
options may be used to limit access a process might have to the file
system hierarchy. Each setting takes a space-separated list of paths
relative to the host's root directory (i.e. the system running the
service manager). Note that if paths contain symlinks, they are resolved
relative to the root directory set with RootDirectory=/RootImage=.
Paths listed in ReadWritePaths= are accessible from within
the namespace with the same access modes as from outside of
it.
+ProtectControlGroups=yes
If true, the Linux Control Groups (cgroups(7)) hierarchies accessible
through /sys/fs/cgroup will be made read-only to all processes of the
unit.
+ProtectKernelModules=yes
If true, explicit module loading will be denied. This allows module
load and unload operations to be turned off on modular kernels.
For further explanation to all directives see `man systemd.directives`
