The start_ap method was raising potential dbus errors before converting
them to an IWD error type. This is due to dbus.Set() not taking an error
handler. The only way to address this is to catch the error, convert it
and raise the converted error.
Two new hardware configuration keys were added:
[radX]
iftype_disable=station,ap,adhoc,p2p_client,p2p_go,mesh_point
cipher_disable=wep40,wep104,tkip,ccmp,bip
Any of the above values are supported and can be disabled.
Support is coming to configure radios with a specific set of interface
type and cipher support, so the input to create_hwsim_radio is better
suited to use a parameter structure rather than adding more parameters.
The radio_confs key was parsed in a way that required all radios
to be specified in the list. This isnt optimal, as you may want to
specially configure a certain radio, while keeping all the others
default.
This change reworks some logic and allows any radio to be specially
configured on its own.
mac80211_hwsim now allows setting supported iftypes/ciphers. This patch
enables this support in hwsim. Specific iftypes/ciphers can now be
disabled via the command line when creating a radio:
Disable iftypes:
--iftype-disable station,ap,adhoc,p2p_client,p2p_go,mesh_point
Disable cipher types:
--cipher-disable ccmp,tkip,wep
The test should be aborted if there are not enough radios that support
AP mode. The iftype attribute will now be parsed during the wiphy dump
and a flag is set on the wiphy so we know to skip this radio when
creating the hostapd instances. Since hostapd gets started first, it
will automatically choose all the radios it needs which support AP mode.
This leaves the remainder of the radios (potentially STA only) for IWD.
In the PCI/USB passthrough changes the wiphy ID was changed to be an
unsigned integer, where id zero corresponded to an error when in native
hardware mode. Along with this, the radio ID for hwsim was changed to a
pre-increment (only in test-runner), so the radio IDs would start at 1.
The repercussions were not fully investigated, but if they were it would
have been seen that hwsim creates radios IDs starting at zero. This left
test-runner and hwsim with unsynchronized radio IDs, and radio zero
never got deleted after each test causing each successive test to
discover old radio IDs.
ifaddr is not guaranteed to be initialized, I'm not sure why there was
no compiler warning. Also replace a | with a || for boolean conditions
and merge the wiphy check with that line.
When handling a scan finished event for a scan we haven't started check
that we were not halfway through a scan request that would have its
results flushed by the external scan.
-nodefconfig doesn't exist anymore and according to the docs it either
had the same meaning or was implied by -no-user-config so it wouldn't be
needed anyway. -balloon doesn't exist anymore and according to
https://lists.gnu.org/archive/html/qemu-devel/2018-02/msg06985.html
"-balloon none" was a nop, but I suspect -nodefaults may have already
had the effect of disabling creation of the virtio-balloon device.
FT-over-DS is a way to do a Fast BSS Transition using action frames for
the authenticate step. This allows a station to start a fast transition
to a target AP while still being connected to the original AP. This,
in theory, can result in less carrier downtime.
The existing ft_sm_new was removed, and two new constructors were added;
one for over-air, and another for over-ds. The internals of ft.c mostly
remain the same. A flag to distinguish between air/ds was added along
with a new parser to parse the action frames rather than authenticate
frames. The IE parsing is identical.
Netdev now just initializes the auth-proto differently depending on if
its doing over-air or over-ds. A new TX authenticate function was added
and used for over-ds. This will send out the IEs from ft.c with an
FT Request action frame.
The FT Response action frame is then recieved from the AP and fed into
the auth-proto state machine. After this point ft-over-ds behaves the
same as ft-over-air (associate to the target AP).
Some simple code was added in station.c to determine if over-air or
over-ds should be used. FT-over-DS can be beneficial in cases where the
AP is directing us to roam, or if the RSSI falls below a threshold.
It should not be used if we have lost communication to the AP all
(beacon lost) as it only works while we can still talk to the original
AP.
To support FT-over-DS this API needed some slight modifications:
- Instead of setting the DA to netdev->handshake->aa, it is just set to
the same address as the 'to' parameter. The kernel actually requires
and checks for these addresses to match. All occurences were passing
the handshake->aa anyways so this change should have no adverse
affects; and its actually required by ft-over-ds to pass in the
previous BSSID, so hard coding handshake->aa will not work.
- The frequency is is also passed in now, as ft-over-ds needs to use
the frequency of the currently connected AP (netdev->frequency get
set to the new target in netdev_fast_transition. Previous frequency
is also saved now).
- A new vector variant (netdev_send_action_framev) was added as well
to support sending out the FT Request action frame since the FT
TX authenticate function provides an iovec of the IEs. The existing
function was already having to prepend the action frame header to
the body, so its not any more or less copying to do the same thing
with an iovec instead.
Since FT already handles processing the FT IE's (and building for
associate) it didn't make sense to have all the IE building inside
netdev_build_cmd_ft_authenticate. Instead this logic was moved into
ft.c, and an iovec is now passed from FT into
netdev_ft_tx_authenticate. This leaves the netdev command builder
unburdened by the details of FT, as well as prepares for FT-over-DS.
