The netdev_copy_tk function was being hard coded with authenticator
set to false. This isn't important for any ciphers except TKIP but
now that AP mode supports TKIP it needs to be fixed.
Though TKIP is deprecated and insecure its trivial to support it in
AP mode as we already do in station. This is only to allow AP mode
for old hardware that may only support TKIP. If the hardware supports
any higher level cipher that will be chosen automatically.
The key descriptor version was hard coded to HMAC_SHA1_AES which
is correct when using IE_RSN_AKM_SUITE_PSK + CCMP. ap.c hard
codes the PSK AKM but still uses wiphy to select the cipher. In
theory there could be hardware that only supports TKIP which
would then make IWD non-compliant since a different key descriptor
version should be used with PSK + TKIP (HMAC_MD5_ARC4).
Now use a helper to sort out which key descriptor should be used
given the AKM and cipher suite.
Similarly to l_netconfig track whether IWD's netconfig is active (from
the moment of netconfig_configure() till netconfig_reset()) using a
"started" flag and avoid handling or emitting any events after "started"
is cleared.
This fixes an occasional issue with the Netconfig Agent backend where
station would reset netconfig, netconfig would issue DBus calls to clear
addresses and routes, station would go into DISCONNECTING, perhaps
finish and go into DISCONNECTED and after a while the DBus calls would
come back with an error which would cause a NETCONFIG_EVENT_FAILED
causing station to call netdev_disconnct() for a second time and
transition to and get stuck in DISCONNECTING.
Both CMD_ASSOCIATE and CMD_CONNECT paths were using very similar code to
build RSN specific attributes. Use a common function to build these
attributes to cut down on duplicated code.
While here, also start using ie_rsn_cipher_suite_to_cipher instead of
assuming that the pairwise / group ciphers can only be CCMP or TKIP.
Instead of copy-pasting the same basic operation (memcpy & assignment),
use a goto and a common path instead. This should also make it easier
for the compiler to optimize this function.
The known frequency list may include frequencies that once were
allowed but are now disabled due to regulatory restrictions. Don't
include these frequencies in the roam scan.
These events are sent if IWD fails to authentiate
(ft-over-air-roam-failed) or if it falls back to over air after
failing to use FT-over-DS (try-ft-over-air)
If IPv4 setup fails and the netconfig logic gives up, continue as if the
connection had failed at earlier stages so that autoconnect can try the
next available network.
Certain drivers support/require probe response offloading which
IWD did not check for or properly handle. If probe response
offloading is required the probe response frame watch will not
be added and instead the ATTR_PROBE_RESP will be included with
START_AP.
The head/tail builders were reused but slightly modified to check
if the probe request frame is NULL, since it will be for use with
START_AP.
Parse the AP probe response offload attribute during the dump. If
set this indicates the driver expects the probe response attribute
to be included with START_AP.
Clearing all authentications during ft_authenticate was a very large
hammer and may remove cached authentications that could be used if
the current auth attempt fails.
For example the best BSS may have a problem and fail to authenticate
early with FT-over-DS, then fail with FT-over-Air. But another BSS
may have succeeded early with FT-over-DS. If ft_authenticate clears
all ft_infos that successful authentication will be lost.
AP roaming was structured such that any AP roam request would
force IWD to roam (assuming BSS's were found in scan results).
This isn't always the best behavior since IWD may be connected
to the best BSS in range.
Only force a roam if the AP includes one of the 3 disassociation/
termination bits. Otherwise attempt to roam but don't set the
ap_directed_roaming flag which will allows IWD to stay with the
current BSS if no better candidates are found.
There are a few checks that can be done prior to parsing the
request, in addition the explicit check for preparing_roam was
removed since this is taken care of by station_cannot_roam().
Once offchannel completes we can check if the info structure was
parsed, indicating authentication succeeded. If not there is no
reason to keep it around since IWD will either try another BSS or
fail.
This both adds proper handling to the new roaming logic and fixes
a potential bug with firmware roams.
The new way roaming works doesn't use a connect callback. This
means that any disconnect event or call to netdev_connect_failed
will result in the event handler being called, where before the
connect callback would. This means we need to handle the ROAMING
state in the station disconnect event so IWD properly disassociates
and station goes out of ROAMING.
With firmware roams netdev gets an event which transitions station
into ROAMING. Then netdev issues GET_SCAN. During this time a
disconnect event could come in which would end up in
station_disconnect_event since there is no connect callback. This
needs to be handled the same and let IWD transition out of the
ROAMING state.
This finalizes the refactor by moving all the handshake prep
into FT itself (most was already in there). The netdev-specific
flags and state were added into netdev_ft_tx_associate which
now avoids any need for a netdev API related to FT.
The NETDEV_EVENT_FT_ROAMED event is now emitted once FT completes
(netdev_connect_ok). This did require moving the 'in_ft' flag
setting until after the keys are set into the kernel otherwise
netdev_connect_ok has no context as to if this was FT or some
other connection attempt.
In addition the prev_snonce was removed from netdev. Restoring
the snonce has no value once association begins. If association
fails it will result in a disconnect regardless which requires
a new snonce to be generated
This converts station to using ft_action/ft_authenticate and
ft_associate and dropping the use of the netdev-only/auth-proto
logic.
Doing this allows for more flexibility if FT fails by letting
IWD try another roam candidate instead of disconnecting.
