Any test using assertTrue(hostapd.list_sta()) improperly has been
replaced with wait_for_event(). There were a few places where this
was actually ok (i.e. IWD is already connected) but most needed to
be changed since the check was just after IWD connected and hostapd's
list_sta() API may not return a fully updated list.
- Setting the IP address was resulting in an error:
Error: any valid prefix is expected rather than "wln58".
This is fixed by reordering the arguments with the IP address first
- Remove the sleep, and use non_block_wait to wait for the IPv6 address
to be set.
Before setting the address, wait for the interface to go down. This
fixes somewhat rare cases where setting the address returns -EBUSY
and ultimately breaks the neighbor reports.
All tests which could avoid calling scan() directly have been
changed to use the 'full_scan' argument to get_ordered_network.
This was done because of unreliable scanning behavior on slower
systems, like VMs. If we get unlucky with the scheduler some beacons
are not received in time and in turn scan results are missing.
Using full_scan=True works around this issue by repeatedly scanning
until the SSID is found.
When configuring wpa_supplicant all we care about is that it
received the configuration object. wpa_supplicant takes quite a bit
of time to connect in some cases so waiting for that is unneeded.
This also increases the DPP timeout which may be required on slower
systems or if the timing is particularly unlucky when receiving
frames.
Change a few critical checks that were failing sometimes:
- A few asserts were changed to wait_for_object_condition
- A 15 second timeout was removed (default used instead)
- Do a full scan at beginning of each test to clear any
cached BSS's. The second test run was getting stale results
and the RSSI values were not expected.
This was not being properly honored when existing networks were
already populated. This poses an issue for any test which uses
full_scan after setting radio values such as signal strength.
If an event is in response to some command which is returning an
unexpected value (unexpected with respect to wpas.py) handle_eow
would raise an exception.
Specifically with DPP this was being hit when the URI was being
returned.
Adds a new wait argument which, if false, will call the DBus method
and return immediately. This allows the caller to create multiple
radios very quickly, simulating (as close as we can) a wifi card
with dual phy's which appear in the kernel simultaneously.
The name argument was also changed to be mandatory, which is now
required by hwsim.
This simulates the conditions that trigger a free-after-use which was
fixed with:
2c355db7 ("scan: remove periodic scans from queue on abort")
This behavior can be reproduced reliably using this test with the above
patch reverted.
During investigation another separate crash was found. The original is
caused by a disconnect event coming in after a neighbor report scan
was completed (roam failed) during the full roam scan.
The second crash is caused by a disconnect coming in during a full
roam scan when no neighbor report scan was ever issued.
First disconnect wpa_supplicant to make sure it wont miss frames if
it decides to connect. Also alter the order of things for the
configurator test so autoconnect doesn't start until after hostapd
is up (avoids additional scanning and delays)
Controlling wpa_supplicant/hostapd from a text based interface is
problematic in that there is no way of knowing if an event corresponds
to a request. In certain cases if wpa_s/hostapd is sending out multiple
events and we make a request, a random event may come back after the
request, but before the actual result.
To fix this, at least for this specific case, we can continue to read
from the socket until the result is numeric.
Some wpa_cli utilities return some result which isn't possible to
get with wait_for_event unless you know what the result will be.
This adds wait_for_result which just returns the first event that
comes in.
wait_for_event was checking the event string presence in the rx_data
array which meant the event string had to match perfectly to any
received events. This poses problems with events that include additional
information which the caller may not be able to know or does not care
about. For example:
DPP-RX src=02:00:00:00:02:00 freq=2437 type=11
Waiting for this event previously would require the caller know src, freq,
and type. If the caller only wants to wait for DPP-RX, it can now do that.
Since a Device class can represent multiple modes (AP, AdHoc, station)
move StationDebug out of the init and only create this class when it
is used (presumably only when the device is in station mode).
The StationDebug class is now created in a property method consistent
with 'station_if'. If Device is not in station mode it is automatically
switched if the test tries any StationDebug methods.
If the Device mode is changed from 'station' the StationDebug class
instance is destroyed.
Passing the full argument list to StationDebug was removed
because any existing properties (for Device) were being
included and causing incorrect behavior.
This neglected to handle namespaces which should also be
passed to StationDebug. Unfortunately the arguments are not
named when Device() is initialized so they cannot easily be
sorted. Instead just define Device() arguments to match the
DBus abstraction and pass only the path and namespace to
StationDebug
Make sure we wipe the leases file both for server and client, so that
dhclient doesn't try to re-use leases from previous tests (should really
happen) and waste time waiting for a reply. Extend the timeout from 1s
to 5s, sometimes it takes dhclient 1s just to start. Disable verbose
mode if not needed to avoid dhclient stalling if the pipe is not being
read.
Passing *args, **kwargs into StationDebug ended up initializing the
class with Station properties since devices can be initialized from
existing property dictionaries. Since the object path is all
StationDebug needs, pass args[0] instead.
