In order to support identifiers the test profiles needed to be
reworked due to hostapd allowing multiple password entires. You
cannot just call set_value() with a new entry as the old ones
still exist. Instead use a unique password for the identifier and
non-identifier use cases.
After adding this test the failure_test started failing due to
hostapd not starting up. This was due to the group being unsupported
but oddly only when hostapd was reloaded (running the test
individually worked). To fix this the group number was changed to 21
which hostapd does support but IWD does not.
This test simulates the scenario where IWDs commit is not acked which
exposes a hostapd bug that ultimately fails the connection. This behavior
can be seen by reverting the commit which works around this issue:
"sae: don't send commit in confirmed state"
With the above patch applied this test should pass.
Note: The existing timeout test was reused as it was not of much use
anyways. All it did was block auth/assoc frames and expect a failure
which didn't exercise any SAE logic anyways.
This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
With the addition of connect_bssid/roam very few tests actually
require hwsim. Since hwsim can lead to problems with scan results
its best to have it off by default and have each test that needs
it explicitly turn it on.
Tests which previously turned it off have had that option removed.
Tests that do require hwsim still are vulnerable to scan result
problems, so for these tests beacon_int was added to the hostapd
config which seems to help with reliability somewhat.
Break up the SAE tests into two parts: testSAE and testSAE-AntiClogging
testSAE is simplified to only use two radios and a single phy managed
by hostapd. hostapd configurations are changed via the new 'set_value'
method added to hostapd utils. This allows forcing hostapd to use a
particular sae group set, or force hostapd to use SAE H2E/Hunting and
Pecking Loop for key derivation. A separate test for IKE Group 20 is no
longer required and is folded into connection_test.py
testSAE-AntiClogging is added with an environment for 5 radios instead
of 7, again with hostapd running on a single phy. 'sae_pwe' is used to
force hostapd to use SAE H2E or Hunting and Pecking for key derivation.
Both Anti-Clogging protocol variants are thus tested.
main.conf is added to both directories to force scan randomization off.
This seems to be required for hostapd to work properly on hwsim.
Both these tests create many radios which sometimes causes timing
problems when hwsim is running. Since hwsim is not required for
these tests we can disable it and increase test reliability.
Many tests waited on the network object 'connected' property after
issuing a Connect command. This is not correct as 'connected' is
set quite early in the connection process. The correct way of doing
this is waiting for the device state to change to connected.
This common code was replaced, hopefully putting to rest any random
failures that happen occasionally.
Slower systems may not be able to make some timeouts that tests
mandated. All timeouts were increased significantly to allow tests
to pass on slow systems.
This test was unreliable since it was assuming a periodic scan would
happen at just the right time. Instead since we are expecting autoconnect
we can just wait for DeviceState.connected then after we are connected
verify the network was correct.
The tests basically remained the same with a few minor changes.
The wiphy_map and in turn hostapd_map are no longer used. This
was already partially converted a long time ago when the 'config'
parameter was added to HostapdCLI. This patch fully converts all
autotests to use 'config' rather than looking up by interface.
Some test scripts were named 'test.py' which was fine before but
the new rewrite actually loads each python test as a module. The
name 'test' is too ambiguous and causes issues due to a native
python module with the same name. All of these files were
renamed to 'connection_test.py'.
Doing this scan causes issues in the test. Like with other autoconnect
tests we can just use the fact that IWD will always be doing a periodic
scan during start up, so we only need to wait for that to finish before
querying the network list.
Don't use del wd to dereference the IWD instance at the end of the function
where it has been defined in the first place as at this point wd is about
to have its reference count decreased anyway (the variable's scope is
ending) so it's pointless (but didn't hurt).
Relying on the __del__ destructor to kill the IWD process in those tests
it has been started in the constructor is a bit of a hack in the first
place, because the destructor is called on garbage collection and even
through CPython does this on the refcount reaching 0, this is not
documented and there's no guideline on when it should happen or if it
should happen at all. So it could be argued that we should keep the del
wd statemenets to be able to easily replace all of them with a call to a
new method. But most of them are not placed so that they're guaranteed
to happen on test success or failure. It would probably be easier to do
this and other housekeeping in a base class and make the tests its
subclasses. Also some of these tests don't really need to launch iwd
themselves, since IWD now tracks changes in the known network files I
think IWD only really needs to be killed between tests when main.conf
changes.
In the tests that only want to iterate over the hostapd interfaces,
simplify the pattern of walking through the whole wiphy_map tree by
instead using the hostapd_map variable which is already filtered to only
contain hostapd interfaces.
SAE has a clogging test which requires 4 radios to all simultaneously
connect. All the other tests are only using one of these radios, so
in these tests we explicitly disconnect these devices preventing them
from autoconnecting.
