This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
The scan ranking logic was previously changed to be based off a
theoretical calculated data rate rather than signal strength.
For HT/VHT networks there are many data points that can be used
for this calculation, but non HT/VHT networks are estimated based
on a simple table mapping signal strengths to data rates.
This table starts at a signal strength of -65 dBm and decreases from
there, meaning any signal strengths greater than -65 dBm will end up
getting the same ranking. This poses a problem for 3/4 blacklisting
tests as they set signal strengths ranging from -20 to -40 dBm.
IWD will then autoconnect to whatever network popped up first, which
may not be the expected network.
To fix this the signal strengths were changed to much lower values
which ensures IWD picks the expected network.
This test fails randomly, and it appears to be due to excessive
scanning. Historically most autotests start a dbus scan right
away. The problem is that most likely a periodic scan is already
ongoing, meaning the dbus scan gets queued. If a Connect() call
comes in (which it always does), the dbus scan gets delayed and will
trigger once connected, at a time the test is not expecting. This
can cause problems with any assumed timing as well as offchannel
frames.
This patch removes the explicit DBus scanning and instead uses
scan_if_needed with get_ordered_networks. The 'all_blacklisted_test'
was also modified to wait for scanning to complete after failing
to connect to all BSS's. This lets all the networks fully come
up (after being blocked by hwsim) and appear in scan results.
Many tests waited on the network object 'connected' property after
issuing a Connect command. This is not correct as 'connected' is
set quite early in the connection process. The correct way of doing
this is waiting for the device state to change to connected.
This common code was replaced, hopefully putting to rest any random
failures that happen occasionally.
There were a number of fixes here. The waits were changed to wait
on the device state instead of the network state and hwsim rules
were removed after the test as to not interfere with future tests.
One of the rules was setting the signal to -10000 wich was causing
the ranking to be zero.
Slower systems may not be able to make some timeouts that tests
mandated. All timeouts were increased significantly to allow tests
to pass on slow systems.
The tests basically remained the same with a few minor changes.
The wiphy_map and in turn hostapd_map are no longer used. This
was already partially converted a long time ago when the 'config'
parameter was added to HostapdCLI. This patch fully converts all
autotests to use 'config' rather than looking up by interface.
Some test scripts were named 'test.py' which was fine before but
the new rewrite actually loads each python test as a module. The
name 'test' is too ambiguous and causes issues due to a native
python module with the same name. All of these files were
renamed to 'connection_test.py'.
This test was not reliably passing. Busy waiting is not really reliable,
but in this specific case its really the only option as the blacklist
must expire based on time.
These values were meant only to force IWD's BSS preference but
since the RSSI's were so low in some cases this caused a roam
immediately after connecting. This patch changes the RSSI values
to prevent a roam from happening.
This removes all the duplicated code where the interfaces are iterated
and the radio/hostapd instances are created. Instead the two new APIs
are used to get each instance, e.g.:
hapd = HostapdCLI(config='ssid.conf')
radio = hwsim.get_radio('radX')
Don't use del wd to dereference the IWD instance at the end of the function
where it has been defined in the first place as at this point wd is about
to have its reference count decreased anyway (the variable's scope is
ending) so it's pointless (but didn't hurt).
Relying on the __del__ destructor to kill the IWD process in those tests
it has been started in the constructor is a bit of a hack in the first
place, because the destructor is called on garbage collection and even
through CPython does this on the refcount reaching 0, this is not
documented and there's no guideline on when it should happen or if it
should happen at all. So it could be argued that we should keep the del
wd statemenets to be able to easily replace all of them with a call to a
new method. But most of them are not placed so that they're guaranteed
to happen on test success or failure. It would probably be easier to do
this and other housekeeping in a base class and make the tests its
subclasses. Also some of these tests don't really need to launch iwd
themselves, since IWD now tracks changes in the known network files I
think IWD only really needs to be killed between tests when main.conf
changes.
In the tests that only want to iterate over the hostapd interfaces,
simplify the pattern of walking through the whole wiphy_map tree by
instead using the hostapd_map variable which is already filtered to only
contain hostapd interfaces.
The simplest way to test this was to create a new AP, where
max_num_sta=1. This only allows a single STA to connect to this AP.
We connect a device to this AP, then try and connect with another.
This results in hostapd failing with DENIED_NO_MORE_STAS, which will
cause a temporary blacklist. We can then disconnect both devices,
and reconnect the device that previously got denied. If it connects
then we know the blacklist only persisted for that earlier connection.
