A recent change checked the return value of ie_parse_rsne_from_data
inside the ptk 1/4 handler. This seemed safe, but actually caused
the eapol unit test to fail.
The reason was because eapol was parsing the IEs assuming they were
an RSN, when they could be a WPA IE (WPA1 not WPA2). The WPA case
does not end up using the rsn_info at all, so having rsn_info
uninitialized did not pose a problem. After adding the return value
check it was found this fails every time for WPA1.
Since the rsn_info is not needed for WPA1 we can only do the RSN
parse for WPA2 and leave rsn_info uninitialized.
The intent here was to validate that the frequency is a multiple of 5
and lies in a certain range. Somehow the channel was checked for being
a multiple of 5 instead.
The logic here intended to check whether all required attributes were
available. However, it set the parse_error to true instead of
have_required to false as intended.
Replace uses of strcpy by the safer l_strlcpy. Note that both of these
functions can only be called with a buffer of max 253 bytes (the
identity string), so this is purely a precautionary measure.
Technically there's no problem here as l_queue_remove does not
dereference the pointer. Still, it confuses certain static analysis
tools in the current form. Reordering this will not change the behavior
at all.
This was refactored to set the mtu via __eap_set_config rather than
passing the MTU into eap_init. This makes eap work in a similar fashion
as eapol (i.e. __eapol_set_config).
If __eap_set_config is not used, the MTU will be set to 1020, which is
the same as previously passing 0 to eap_init.
Since iwd_modules_init is now defered until nl80211_appeared, we can
assume the nl80211 object is available. This removes the need for
netdev_set_nl80211 completely.
In preparation for integrating IWD_MODULE into modules which require
nl80211 we move the module init into the nl80211_appeared callback.
This will guarentee that the nl80211 is available during module init
and allow modules to get their own copy of nl80211 rather than needing
a set function (e.g. netdev_set_nl80211).
Since the dbus name request callback happens before this as well any
dbus module can also use IWD_MODULE and simply assume the dbus object
is ready.
plugin_init was also deferred to nl80211_appeared since some plugins
depend on modules being initialized.
Converts agent into an IWD module. This removes the dbus dependency
on agent. Since dbus is initialized very early we can assume
dbus_get_bus is going to return a valid object.
Previously, station state 'connected' used to identify an interface associated
with AP. With the introduction of netconfig, an interface is assumed to be
connected after the IP addresses have been assigned to it. If netconfig is
disabled, the behavior remains unchanged.
Refactoring was required to allow for embedded certs. The existing
eap_tls_state object was changed to hold the cert types (l_queue,
l_certchain, l_key) rather than the file path, since there may not
actually be separate PEM files.
Care was taken to properly manage the memory of these objects.
Since the TLS object takes ownership when setting auth data or the
CA certs all error cases must be handled properly to free these
objects after they are loaded and in addition they must be set to
NULL so that the cleanup doesn't double free them.
If everything goes to plan, we load all the PEMs in settings_load,
provide these objects to the TLS APIs, and then NULL out the
pointers (TLS now owns this memory). If anything fails between
settings_load and l_tls_start we must free these objects.
A special format must be used to indicate that a PEM is embedded
inside the settings file. First, the l_settings format should be
followed for the PEM itself, e.g.
[@pem@my_ca_cert]
<CA Cert data>
This PEM can then be referenced by "embed:my_ca_cert", e.g.
EAP-TLS-CACert=embed:my_ca_cert
Any other value not starting with "embed:" will be treated as a file
path.
The IPv6 default route needs to be explicitly revoked. Unlike in IPv4,
there is no SRC address associated with the route and it will not be
removed on address removal.
The network configuration options for IPv6 are grouped under [IPv6]
and include the following:
ip= ADDRESS/PREFIX
gateway=ADDRESS
dns=ADDRESS
The placeholders for DHCPv6 are placed along the way and marked
as TODO items.
Previously, netconfig_ipv4_select_and_install was used to install
addresses on initial connection to a network and after we have roamed.
Now for the after roaming connection scenario we have
netconfig_reconfigure. Remove roaming related code from
netconfig_ipv4_select_and_install
As part of the de-coupling from station object, switch all of
the network settings inquiries to use active_settings. active_settings
are set with netconfig_configure by the owner of netconfig object
and removed with netconfig_reset once network disconnects.
Instead of relying on station state changed signal, netconfig
introduces three new API calls to configure, re-configure and
reset the network configurations. The owner of netconfig object
is responsible for initiating the re-configuration of the device
depending on its state.
As a first step to enable the usage of netconfig in ead and
prospective transition to be a part of ell, the public API for
creation and destruction of the netconfig objects has been
renamed and changed. Instead of hiding the netconfig objects inside
of netconfig module, the object is now passed back to the caller.
The internal queue of netconfig objects remains untouched, due
to limitations in ell’s implementation of rtnl. After the proper
changes are done to ell, netconfig_list is expected to be removed
from netconfig module.
A NEW_WIPHY event may not always contain all the information about a
given phy, but GET_WIPHY will. In order to get everything we must
mimic the behavior done during initalization and dump both wiphy
and interfaces when a NEW_WIPHY comes in.
Now, any NEW_WIPHY event will initialize a wiphy, but then do a
GET_WIPHY/GET_INTERFACE to obtain all the information. Because of
this we can ignore any NEW_INTERFACE notifications since we are
dumping the interface anyways.
Once some kernel changes get merged we wont need to do this anymore
so long as the 'full' NEW_WIPHY feature is supported.
If the AP sent us the plain passphrase we can now store that rather
than generating the PSK. This will allow WPA3 to work properly when
WPA3 + WSC is implemented.
This lets other modules (like WSC) to set a plain text passphrase
as opposed to only allowing a PSK to be set. network_get_psk was
also updated to generate a PSK on-the-fly if required. Since WPA3
requires the raw passphrase to work, it makes sense to just store
the passphrase if we have it.
If neighbor reports are unavailable, or the report yielded no
results we can quickly scan for only known frequencies. This
changes the original behavior where we would do a full scan
in this case.
This password key was deprecated in favor of the common EAP-Password
key. Its been about a year so we are now removing support entirely
for EAP-PWD-Password.
Marcel Holtmann