This test took quite a while to execute (~2 minutes on my machine)
because there was simply no other way to test this scenario but
waiting. Now the no-roam-candidates condition can be waited for
rather than just sleeping for 20 seconds. Additionally the default
RoamRetryInterval was being used which is 60 seconds. Instead
main.conf can set this to 5 seconds and really cut down on the time
to wait.
Part of a comment was also removed due to being incorrect. Even
with neighbor reports IWD still must scan, its just that the
scan is more limited and, in theory, faster.
get_ordered_network() now scans automatically and has been updated
to use the StationDebug.Scan() API rather than doing a full
dbus scan (unless full_scan = True). The frequencies to be scanned
are picked automatically based on the current hostapd status
(hidden behind ctx.hostapd.get_frequency()).
This changes all tests to use the default get_ordered_network behavior
rather than some custom or incorrect logic. Any use of
scan_if_needed=True has been removed since this is now the default.
Also any explicit scanning has been removed for tests which do not
require it (where the default behavior is good enough).
With the addition of connect_bssid/roam very few tests actually
require hwsim. Since hwsim can lead to problems with scan results
its best to have it off by default and have each test that needs
it explicitly turn it on.
Tests which previously turned it off have had that option removed.
Tests that do require hwsim still are vulnerable to scan result
problems, so for these tests beacon_int was added to the hostapd
config which seems to help with reliability somewhat.
There is a common block of code in nearly every test which is incorrect,
most likely a copy-paste from long ago. It goes something like:
wd.wait_for_object_condition(device, 'not obj.scanning')
device.scan()
wd.wait_for_object_condition(device, 'not obj.scanning')
network = device.get_ordered_network("ssid")
The problem here is that sometimes the scanning property does not get
updated fast enough before device.scan() returns, meaning get_ordered_network
comes up with nothing. Some tests pass scan_if_needed=True which 'fixes'
this but ends up re-scanning after the original scan finishes.
To put this to rest scan_if_needed is now defaulted to True, and no
explicit scan should be needed.
In addition the send_bss_transition call was updated to only send a
single BSS. By sending two BSS's IWD is left to pick whichever one
it wants which makes the test behavior undefined.
This will use the Roam() developer method to force a roam to
a certain BSS. This is particularly useful for any test requiring
roams that are not testing IWD's BSS selection logic. Rather than
creating hwsim rules, setting low RSSI values, and waiting for the
roam logic/scan to happen Roam() can be used to force the roam
logic immediately.
Several tests tests for connectivity with the expectation that it
will fail. This ends up taking 30+ seconds because testutil retries
3 times, each with a 10 second timeout. By passing expect_fail=True
this lowers the timeout to zero, and skips any retries.
After some code changes the FT-FILS AKM was no longer selectable
inside network_can_connect_bss. This normally shouldn't matter
since station ends up selecting the AKM explicitly, including
passing the fils_hint, but since the autotests only included
FT-FILS AKMs this caused the transition to fail with no available
BSS's.
To fix this the standard 8021x AKM was added to the hostapd
configs. This allows these BSS's to be selected when attempting
to roam, but since FT-FILS is the only other AKM it will be used
for the actual transition.
testScan was creating 10 separate hidden networks which
sometimes bogged down hostapd to the point that it would
not start up in time before test-runner's timeouts fired.
This appeared to be due to hostapd needing to create 10
separate interfaces which would sometimes fail with -ENFILE.
The test itself only needed two separate networks, so instead
the additional 8 can be completely removed.
The scan ranking logic was previously changed to be based off a
theoretical calculated data rate rather than signal strength.
For HT/VHT networks there are many data points that can be used
for this calculation, but non HT/VHT networks are estimated based
on a simple table mapping signal strengths to data rates.
This table starts at a signal strength of -65 dBm and decreases from
there, meaning any signal strengths greater than -65 dBm will end up
getting the same ranking. This poses a problem for 3/4 blacklisting
tests as they set signal strengths ranging from -20 to -40 dBm.
IWD will then autoconnect to whatever network popped up first, which
may not be the expected network.
To fix this the signal strengths were changed to much lower values
which ensures IWD picks the expected network.
Break up the SAE tests into two parts: testSAE and testSAE-AntiClogging
testSAE is simplified to only use two radios and a single phy managed
by hostapd. hostapd configurations are changed via the new 'set_value'
method added to hostapd utils. This allows forcing hostapd to use a
particular sae group set, or force hostapd to use SAE H2E/Hunting and
Pecking Loop for key derivation. A separate test for IKE Group 20 is no
longer required and is folded into connection_test.py
testSAE-AntiClogging is added with an environment for 5 radios instead
of 7, again with hostapd running on a single phy. 'sae_pwe' is used to
force hostapd to use SAE H2E or Hunting and Pecking for key derivation.
Both Anti-Clogging protocol variants are thus tested.
main.conf is added to both directories to force scan randomization off.
This seems to be required for hostapd to work properly on hwsim.
[General].APRange is now [IPv4].APAddressPool and the netmask is changed
from 23 to 27 bits to make the test correctly assert that only two
default-sized subnets are allowed by IWD simultaneously (default has
changed from 24 to 28 bits)
These test cases depend on setting up the existing hostapd instance to a
set of known addresses, which might be different from what test-runner
sets. During this time, any scans might result in the old and the new
addresses used by hostapd to be found in the scan results.
Fix that by using start_iwd=0 which tells test_runner that the test
wants to start iwd itself. This delays starting iwd until after the
setUpClass routine has been called and hostapd configured properly.
Also use more sensible rssi values for the 'non-preferred' bss.
Otherwise, ranking BSSes by throughput can confuse the test logic
since both BSSes are ranked the same and either can be picked by
autoconnect.
The FT-over-DS procedure now authenticates with multiple BSS's
upon connecting. This causes list_sta() to return our address for
any authenticated APs. It has now been changed to work with this
new behavior, as well as a check that the station fully connected
to the expected AP initially.
