Update the expected DBus exception in the manual connect case, affected
by recent EAP changes. Also slightly improve the comment in the file
although it's still not 100% correct.
This also tests multiple agent requests for one network connection
because the TTLS client private key is not in the config file and the
MSCHAPV2 password is not in the config file.
Make 3 connections in test EAP-TLS, one with an unencrypted private key,
one with the private key passphrase provided in the provisioning file
and one with the passphrase provided through the agent. Also improve
the scanning logic at the beginning.
Allow passing a list of passphrases for subsequent agent requests to the
PSKAgent constructor. This also makes existing tests stricter because
a spurious agent request will not receive the same passphrase.
If --gdb is used with test-runner, all the timeouts in the
IWD class must be turned off otherwise the test will fail.
Inside test-runner, a environment variable (IWD_TEST_TIMEOUTS)
is set to either 'on' or 'off'. Then the IWD class (and any
others) can handle the timeouts accordingly. Note that this
does not turn off dbus timeouts, rather it ignores timeout
failures. This does mean that ultimately the test will most
likely fail due to a dbus timeout, but it at least gives you
unlimited debugging time.
Two autotests:
1. Tests SA Query procedure when the AP goes down. In this case the AP
goes down ungracefully, now allowing it to send out any deauth
frames. When the AP comes back up, IWD still thinks its connected.
The AP will then send unprotected disassociate frames so the client
can re-connect. This kicks off the SA Query procedure, which the AP
will not respond to. At this point we can deauth and reconnect to
the AP.
2. Test SA Query procedure when a disassociate frame has been spoofed.
In this case we receive an unprotected disassociate frame and start
SA Query. The AP should then respond to the SA query within the
timeout. We then know the frame was spoofed and can remain
connected.
Changed disassociate reason to 0x07 when spoofing a disassociate
frame. This along with 0x06 are the only two reason codes that
should be accepted in an unprotected disassociate frame.
Using the hwsim dbus interface ".Interface" under the radios
object you can now send an arbitrary frame out from that radio.
Two methods have been added, spoof_frame and spoof_disassociate.
The hwsim SendFrame method requires the radio frequency which
is obtained from the hostapd config file. This adds a generic
API to get any config value from the hostapd config, as well
as a get_freq API that converts the channel number to a
frequency.
For testing SA Query, the autotest needs the ablility to force
kill (and restart) hostapd without giving it time to deauth its
stations gracefully. A method was added to the HostapdCLI class
which does a killall -9 hostapd, resets the wlnX interface,
and restarts hostapd with the same arguments as it had before.
The AuthCenter will now wait for the RX thread to start before
continuing with the test.
Also removed the non blocking option and fixed the loop to
handle a blocking recvfrom call.
If the peer detects a sync error, it sends back AUTS. The
authentication center must then re-synchronize and update
the SQN it has saved for the given ISMI.
For testing purposes, it is useful to run hlrauc.py by itself
not including it from another python script like autotests do.
Better error checking was also added as testing can result in
badly formatted data.
We need to reset self._exception after _wait_for_async_op raises an
exception, otherwise _wait_for_async_op will report that exception for
every future operation (this wasn't an issue when an exception always
meant that the test was failing and objects were torn down anyway)
In the beacon loss test try to simulate a periodic communication problem
because we don't support roaming if the AP goes away completely.
2 seconds seems to be enough to consistently trigger the beacon_loss
event without triggering a disconnect by the linux kernel or hiding the AP
from the roam scan. Also set the RSSI for that AP lower so that it is
not reselected by iwd.
Implemented milenage algorithm in hlrauc.py. Unlike EAP-SIM, the
authentication center must compute several values to give back
to the server (hostapd). This was already done by IWD as the peer
in EAP-AKA, but was also needed on the server side (HLR AuC).
Test that the AP interface and the station interface managed by iwd
can actually send and receive ethernet traffic when iwd is in the
connected state. Due to linux routing none of the high level utilities
like ping or arping can be easily used to test communication between
two interfaces of the same machine so use a method based on the
mac80211_hwsim/tools/hwsim_test.c utility in the wpa_supplicant tree
that uses a raw socket to inject unicast and broadcast frames.
Add this check in three tests of different security type connections
that simulate a single AP, and the two roaming tests with two APs.
Check that the station can't communicate with the other AP's interface.
Unfortunately this doesn't currently ensure that the preauthentication
has succeeded and that later the PMKSA from the preauthentication was
used in the transition, only that the preauthentication process doesn't
break the transition. For now this can be confirmed by looking at the
testrunner -v output to see that the line "EAP completed with eapSuccess"
appears before the following line, and not after:
src/device.c:device_enter_state() Old State: connected, new state: roaming
Sometimes iwd will take a while to register its dbus name. The python
class already waits for the name to appear on dbus if iwd is being
launched from python, do this also if iwd was already launched by the
test-runner. My use case was when running iwd under valgrind in which
case it runs slower.
Modify AsyncOpAbstract._wait_for_async_op and
IWD.wait_for_object_condition to call context.iteration() in the
blocking mode instead of calling context.pending() every 0.01s. This
gets rid of busy-waiting and also ensures that the condition is checked
after every single dbus (or other) event. This way a condition that
potentially occurs for less than 0.01s can be reliably waited for.
Make the HostapdCLI class non-static so that each objects corresponds
to a hostapd instance on one network interface (this is independent of
whether the AP instances use one or separate hostapd processes)
APShutdownTest - shutdown the AP after network connection. This
will be replaced when hwsim supports signal
strength modification
InvalidPassphraseTest - Provide an invalid passphrase.
Where the code just needs to find all of the network objects, don't look
for the device objects first because this only adds overhead. With
the structure now having three levels it can be even more confusing,
especially in getCurrentlyConnectedNetworkName where the outer loop
didn't check for the Device interface.
In getNetworkList don't return after the first device's networks are
listed.
Andrew Zaborowski