Test that the DHCPv4 lease got renewed after the T1 timer runs out.
Then also simulate the DHCPREQUEST during renew being lost and
retransmitted and the lease eventually getting renewed T1 + 60s later.
The main downside is that this test will inevitably take a while if
running in Qemu without the time travel ability.
Update the test and some utility code to run hostapd in an isolated net
namespace for connection_test.py. We now need a second hostapd
instance though because in static_test.py we test ACD and we need to
produce an IP conflict. Moving the hostapd instance unexpectedly fixes
dhcpd's internal mechanism to avoid IP conflicts and it would no longer
assign 192.168.1.10 to the second client, it'd notice that address was
already in use and assign the next free address, or fail if there was
none. So add a second hostapd instance that runs in the main namespace
together with the statically-configured client, it turns out the test
relies on the kernel being unable to deliver IP traffic to interfaces on
the same system.
By creating a new bus connection for each agent we can register multiple
with IWD. This did mean the agent interface needs to be unique for each
agent (removing _agent_manager_if) as well as tracking multiple agents
in a list.
The rekey/reauth logic was broken in a few different ways.
For rekeys the event list was not being reset so any past 4-way
handshake would allow the call to pass. This actually removes
the need for the sleep in the extended key ID test because the
actual handshake event is waited for correctly.
For both rekeys and reauths, just waiting for the EAP/handshake
events was not enough. Without checking if the client got
disconnected we essentially allow a full disconnect and reconnect,
meaning the rekey/reauth failed.
Now a 'disallow' array can be passed to wait_for_event which will
throw an exception if any events in that array are encountered
while waiting for the target event.
In UML if any process dies while test-runner is waiting for the DBus
service or some socket to be available it will block forever. This
is due to the way the non_block_wait works.
Its not optimal but it essentially polls over some input function
until the conditions are met. And, depending on the input function,
this can cause UML to hang since it never has a chance to go idle
and advance the time clock.
This can be fixed, at least for services/sockets, by sleeping in
the input function allowing time to pass. This will then allow
test-runner to bail out with an exception.
This patch adds a new wait_for_service function which handles this
automatically, and wait_for_socket was refactored to behave
similarly.
In iwd.py make sure all the static methods that touch IWD storage take the
storage_dir parameter instead of hardcoding IWD_STORAGE_DIR, and make
sure that parameter is actually used.
Create the directory if it doesn't exist before copying files into it.
This fixes a problem in testNetconfig where
`IWD.copy_to_storage('ssidTKIP.psk', '/tmp/storage')`
would result in /tmp/storage being created as a file, rather than a
directory containing a file, and resulting in IWD failing to start with:
`Failed to create /tmp/storage`
runner.py creates /tmp/iwd but that doesn't account for IWD sessions
with a custom storage dir path.
Extend test_ip_address_match to support IPv6 and to test the
netmask/prefix length while it reads the local address since those are
retrieved using the same API.
Modify testNetconfig to validate the prefix lengths, change the prefix
lengths to be less common values (not 24 bits for IPv4 or 64 for IPv6),
minor cleanup.
Similarly to ofono/phonesim allow tests to be skipped if wpa_supplicant
is not found on the system.
This required some changes to DPP/P2P where Wpas() should be called first
since this can now throw a SkipTest exception.
The Wpas class was also made to allow __del__ to be called without
throwing additional exceptions in case wpa_supplicant was not found.
The current way this was being done was to import collections and
use collections.Mapping. This has been deprecated since python 3.3
but has worked up until python 3.10. After python 3.10 this will
no longer work, and Mapping must be imported from collections.abc.
This was passing IFNAME= along with EAPOL_REAUTH which does not work
in the context of a hostapd socket where the iface is already implied.
This fixes that issue as well as resets the events array and actually
waits for the required events afterwards.
Use scapy library which allows one to easily construct and fudge various
network packets. This makes constructing spoofed packets much easier
and more readable compared to hex-encoded, hand-crafted frames.
The TA/BSSID addresses of spoofed disassociate frames were set
incorrectly. They should be using the 02:00:00:XX:XX:XX address, but
instead were being converted over to 42:00:00:XX:XX:XX address
There is really no reason to have hwsim create interfaces automatically
for test-runner. test-runner already does this for wpa_supplicant and
hostapd, and IWD can create the interface itself.
Similarly to hostapd.wait_for_event, IWD's variant needed to act on
an IO watch because events were being received prior to even calling
wait_for_event.
With how fast UML is hostapd events were being sent out prior to
ever calling wait_for_event. Instead set an IO watch on the control
socket and cache all events as they come. Then, when wait_for_event
is called, it can reference this list. If the event is found any
older events are purged from the list.
The AP-ENABLED event needed a special case because hostapd gets
started before the IO watch can be registered. To fix this an
enabled property was added which queries the state directly. This
is checked first, and if not enabled wait_for_event continues normally.
This was not being properly honored when existing networks were
already populated. This poses an issue for any test which uses
full_scan after setting radio values such as signal strength.
If an event is in response to some command which is returning an
unexpected value (unexpected with respect to wpas.py) handle_eow
would raise an exception.
Specifically with DPP this was being hit when the URI was being
returned.
Adds a new wait argument which, if false, will call the DBus method
and return immediately. This allows the caller to create multiple
radios very quickly, simulating (as close as we can) a wifi card
with dual phy's which appear in the kernel simultaneously.
The name argument was also changed to be mandatory, which is now
required by hwsim.
Controlling wpa_supplicant/hostapd from a text based interface is
problematic in that there is no way of knowing if an event corresponds
to a request. In certain cases if wpa_s/hostapd is sending out multiple
events and we make a request, a random event may come back after the
request, but before the actual result.
To fix this, at least for this specific case, we can continue to read
from the socket until the result is numeric.
Some wpa_cli utilities return some result which isn't possible to
get with wait_for_event unless you know what the result will be.
This adds wait_for_result which just returns the first event that
comes in.
wait_for_event was checking the event string presence in the rx_data
array which meant the event string had to match perfectly to any
received events. This poses problems with events that include additional
information which the caller may not be able to know or does not care
about. For example:
DPP-RX src=02:00:00:00:02:00 freq=2437 type=11
Waiting for this event previously would require the caller know src, freq,
and type. If the caller only wants to wait for DPP-RX, it can now do that.
Since a Device class can represent multiple modes (AP, AdHoc, station)
move StationDebug out of the init and only create this class when it
is used (presumably only when the device is in station mode).
The StationDebug class is now created in a property method consistent
with 'station_if'. If Device is not in station mode it is automatically
switched if the test tries any StationDebug methods.
If the Device mode is changed from 'station' the StationDebug class
instance is destroyed.
Passing the full argument list to StationDebug was removed
because any existing properties (for Device) were being
included and causing incorrect behavior.
This neglected to handle namespaces which should also be
passed to StationDebug. Unfortunately the arguments are not
named when Device() is initialized so they cannot easily be
sorted. Instead just define Device() arguments to match the
DBus abstraction and pass only the path and namespace to
StationDebug
Passing *args, **kwargs into StationDebug ended up initializing the
class with Station properties since devices can be initialized from
existing property dictionaries. Since the object path is all
StationDebug needs, pass args[0] instead.
Certain scenarios coupled with lost beacons could result in OrderedNetwork
being initialized many times until the dbus library reached its maximum
signal registrations. This could happen where there are two networks,
IWD finds one in a scan but continues to scan for the other and the beacons
are lost. The way get_ordered_networks was written it returns early if any
networks are found. Since get_ordered_network (not plural) uses
get_ordered_networks() in a loop this caused OrderedNetwork's to be created
rapidly until python raises an exception.
To fix this, pass an optional list of networks being looked for to
get_ordered_networks. Only if all the networks in the list are found will
it return early, otherwise it will continue to scan.
REKEY_GTK kicks off the GTK only handshake where REKEY_PTK does
both (via the 4-way). The way this utility was written was causing
hostapd some major issues since both REKEY_GTK and REKEY_PTK was
used.
Instead if address is set only do REKEY_PTK. This will also rekey
the GTK via the 4-way handshake.
If no address is set do REKEY_GTK which will only rekey the GTK.
