For symmetry with IPv4, save the command id for this netlink command so
we can later add logic to the callback as well as be able to cancel the
command. No functional change in this commit alone.
FT/FILS handle their own PMK derivation but rekeys still require
using the 4-way handshake. There is some ambiguity in the spec whether
or not the PMKID needs to be included in message 1/4 and it appears
that when rekeying after FT/FILS hostapd does not include a PMKID.
The handshake contains the current BSS's RSNE/WPA which may differ
from the FT-over-DS target. When verifying the target BSS's RSNE/WPA
IE needs to be checked, not the current BSS.
If the deauth path was triggered IWD would deauth but end up
calling the connect callback with whatever result netdev had
set, e.g. 'NETDEV_RESULT_OK'. This, of course, caused station
some confusion.
FT-over-DS cannot use OCV due to how the kernel works. This means
we could connect initially with OCVC set, but a FT-over-DS attempt
needs to unset OCVC. Set OCVC false when rebuilding the RSNE for
reassociation.
The FT-over-DS action stage builds an FT-Request which contains an
RSNE. Since FT-over-DS will not support OCV add a boolean to
ft_build_authenticate_ies so the OCVC bit can be disabled rather
than relying on the handshake setting.
This modifies the FT logic to fist call get_oci() before
reassociation. This allows the OCI to be included in reassociation
and in the 4-way handshake later on.
The code path for getting the OCI had to be slightly changed to
handle an OCI that is already set. First the handshake chandef is
NULL'ed out for any new connection. This prevents a stale OCI from
being used. Then some checks were added for this case in
netdev_connect_event and if chandef is already set, start the 4-way
handshake.
netconfig_load_settings is called when establishing a new initial
association to a network. This function tries to update dhcp/dhcpv6
clients with the MAC address of the netdev being used. However, it is
too early to update the MAC here since netdev might need to powercycle
the underlying network device in order to update the MAC (i.e. when
AddressRandomization="network" is used).
If the MAC is set incorrectly, DHCP clients are unable to obtain the
lease properly and station is stuck in "connecting" mode indefinitely.
Fix this by delaying MAC address update until netconfig_configure() is
invoked.
Fixes: ad228461ab ("netconfig: Move loading settings to new method, refactor")
If the AP advertises FT-over-DS support it likely wants us to use
it. Additionally signal_low is probably going to be true since IWD
has started a roam attempt.
When netdev goes down so does station, but prior to netdev calling
the neighbor report callback. The way the logic was written station
is dereferenced prior to checking for any errors, causing a use
after free.
Since -ENODEV is used in this case check for that early before
accessing station.
This adds a utility to convert a chandef obtained from the kernel into a
3 byte OCI element format containing the operating class, primary
channel and secondary channel center frequency index.
This changes scan_bss from using separate members for each
OWE transition element data type (ssid, ssid_len, and bssid)
to a structure that holds them all.
This is being done because OWE transition has option operating
class and channel bytes which will soon be parsed. This would
end up needing 5 separate members in scan_bss which is a bit
much for a single IE that needs to be parsed.
This makes checking the presense of the IE more convenient
as well since it can be done with a simple NULL pointer check
rather than having to l_memeqzero the BSSID.
These members are currently stored in scan_bss but with the
addition of operating class/band info this will become 5
separate members. This is a bit excessive to store in scan_bss
separately so instead this structure can hold everything related
to the OWE transition IE.
Add a utility for setting the OCI obtained from the hardware (prior to
handshake starting) as well as a utility to validate the OCI obtained
from the peer.
This adds a utility that can convert an operating class + channel
combination to a frequency. Operating class is assumed to be a global
operating class from 802.11 Appendix E4.
This information can be found in Operating Channel Information (OCI) IEs,
as well as OWE Transition Mode IEs.
Calling handshake_state_setup_own_ciphers from within
handshate_state_set_authenticator_ie was misleading. In all cases the
supplicant chooses the AKM. This worked since our AP code only ever
advertises a single AKM, but would not work in the general case.
Similarly, the supplicant would choose which authentication type to use
by either sending the WPA1 or WPA2 IE (or OSEN). Thus the setting of
the related variables in handshake_state_set_authenticator_ie was also
incorrect. In iwd, the supplicant_ie would be set after the
authenticator_ie, so these settings would be overwritten in most cases.
Refactor these two setters so that the supplicant's chosen rsn_info
would be used to drive the handshake.
reallocarray has been added to glibc relatively recently (version 2.26,
from 2017) and apparently not all users run new enough glibc. Moreover,
reallocarray is not available with uclibc-ng. So use realloc if
reallocarray is not available to avoid the following build failure
raised since commit 891b78e9e8:
/home/giuliobenetti/autobuild/run/instance-3/output-1/host/lib/gcc/xtensa-buildroot-linux-uclibc/10.3.0/../../../../xtensa-buildroot-linux-uclibc/bin/ld: src/sae.o: in function `sae_rx_authenticate':
sae.c:(.text+0xd74): undefined reference to `reallocarray'
Fixes:
- http://autobuild.buildroot.org/results/c6d3f86282c44645b4f1c61882dc63ccfc8eb35a
There isn't much control station has with how BSS's are inserted to
a network object. The rank algorithm makes that decision. Because of
this we could end up in a situation where the Open BSS is preferred
over the OWE transition BSS.
In attempt to better handle this any Open BSS in this type of network
will not be chosen unless its the only candidate (e.g. no other BSSs,
inability to connect with OWE, or an improperly configured network).
OWE Transition is described in the WiFi Alliance OWE Specification
version 1.1. The idea behind it is to support both legacy devices
without any concept of OWE as well as modern ones which support the
OWE protocol.
OWE is a somewhat special type of network. Where it advertises an
RSN element but is still "open". This apparently confuses older
devices so the OWE transition procedure was created.
The idea is simple: have two BSS's, one open, and one as a hidden
OWE network. Each network advertises a vendor IE which points to the
other. A device sees the open network and can connect (legacy) or
parse the IE, scan for the hidden OWE network, and connect to that
instead.
Care was taken to handle connections to hidden networks directly.
The policy is being set that any hidden network with the WFA OWE IE
is not connectable via ConnectHiddenNetwork(). These networks are
special, and can only be connected to via the network object for
the paired open network.
When scan results come in from any source (DBus, quick, autoconnect)
each BSS is checked for the OWE Transition IE. A few paths can be
taken here when the IE is found:
1. The BSS is open. The BSSID in the IE is checked against the
current scan results (excluding hidden networks). If a match is
found we should already have the hidden OWE BSS and nothing
else needs to be done (3).
2. The BSS is open. The BSSID in the IE is not found in the
current scan results, and the open network also has no OWE BSS
in it. This will be processed after scan results.
3. The BSS is not open and contains the OWE IE. This BSS will
automatically get added to the network object and nothing else
needs to be done.
After the scan results each network is checked for any non-paired
open BSS's. If found a scan is started for these BSS's per-network.
Once these scan results come in the network is notified.
From here network.c can detect that this is an OWE transition
network and connect to the OWE BSS rather than the open one.
Specifically OWE networks with multiple open/hidden BSS's are troublesome
to scan for with the current APIs. The scan parameters are limited to a
single SSID and even if that was changed we have the potential of hitting
the max SSID's per scan limit. In all, it puts the burden onto the caller
to sort out the SSIDs/frequencies to scan for.
Rather than requiring station to handle this a new scan API was added,
scan_owe_hidden() which takes a list of open BSS's and will automatically
scan for the SSIDs in the OWE transition IE for each.
It is slightly optimized to first check if all the hidden SSID's are the
same. This is the most likely case (e.g. single pair or single network)
and a single scan command can be used. Otherwise individual scan commands
are queued for each SSID/frequency combo.
handshake_util_ap_ie_matches() is used to make sure that the RSN element
received from the Authenticator during handshake / association response
is the same as the one advertised in Beacon/Probe Response frames. This
utility tries to bitwise compare the element first, and only if that
fails, compares RSN members individually.
For FT, bitwise comparison will always fail since the PMKID has to be
included by the Authenticator in any RSN IEs included in Authenticate
& Association Response frames.
Perform the bitwise comparison as an optimization only during processing
of eapol message 3/4. Also keep the parsed rsn information for future
use and to possibly avoid re-parsing it during later checks.
DBus scan is performed in several subsets. In certain corner-case
circumstances it would be possible for autoconnect to run after each
subset scan. Instead, trigger autoconnect only after the dbus scan
completes.
This also works around a condition where ANQP results could trigger
autoconnect too early.
Several invocations of station_set_scan_results() base the
'add_to_autoconnect' parameter on station_is_autoconnecting(). Simplify
the code by having station_set_scan_results() invoke that itself.
'add_to_autoconnect' now becomes an 'intent' parameter, specifying
whether autoconnect path should be invoked as a result of these scan
results or not when station is in an appropriate state. Rename
'add_to_autoconnect' parameter to make this clearer.
If the frequency of the bss is not in the list of frequencies for the
current scan, then this is a cached bss. It was likely already
processed for ANQP before, so skip it.
IWD has restricted SSIDs to only utf8 so they can be displayed but
with the addition of OWE transition networks this is an unneeded
restriction (for these networks). The SSID of an OWE transition
network is never displayed to the user so limiting to utf8 isn't
required.
Allow non-utf8 SSIDs to be scanned for by including the length in
the scan parameters and not relying on strlen().
This is a parser for the WFA OWE Transition element. For now the
optional band/channel bytes will not be parsed as hostapd does not
yet support these and would also require the 802.11 appendix E-1
to be added to IWD. Because of this OWE Transition networks are
assumed to be on the same channel as their open counterpart.
in6_addr.__in6_u.__u6_addr8 is glibc-specific and named differently in
the headers shipped with musl libc for example. The POSIX compliant and
universal way of accessing it is in6_addr.s6_addr.
This was actually broken if triggered because __network_connect
checks if network->connect_after_owe_hidden is set and returns
already in progress. We want to keep this behavior though for
obvious reasons.
To fix this station_connect_network can be called directly which
bypasses the check. This is essentially how ANQP avoids this
problem as well.
Similar to ANQP a connect call could come in while station is
scanning for OWE hidden networks. This is supported in the same
manor by saving away the dbus message and resuming the connection
after the hidden OWE scan.
With the addition of OWE transition network needs to be notified
of the hidden OWE scan which is quite similar to how it is notified
of ANQP. The ANQP event watch can be made generic and reused to
allow other events besides ANQP.
This is being added to support OWE transition mode. For these
type of networks the OWE BSS may contain a different SSID than
that of the network, but the WFA spec requires this be hidden
from the user. This means we need to set the handshake SSID based
on the BSS rather than the network object.
Refactor netconfig_set_dns to be a bit easier to follow and remove use
of macros. Also bail out early if no DNS addresses are provided instead
of building an empty DNS list since resolve_set_dns() simply returns if
a NULL or empty DNS list is provided.
Kernel keeps transmitting authentication frames until told to stop or an
authentication frame the kernel considers 'final' is received. Detect
cases where the kernel would keep retransmitting, and if auth_proto
encounters a fatal protocol error, prevent these retransmissions from
occuring by sending a Deauthenticate command to the kernel.
Additionally, treat -EBADMSG/-ENOMSG return from auth_proto specially.
These error codes are meant to convey that a frame should be silently
dropped and retransmissions should continue.
This works around a hostapd bug (described more in the TODO comment)
which is exposed because of the kernels overly agressive re-transmit
behavior on missed ACKs. Combined this results in a death if the
initial commit is not acked. This behavior has been identified in
consumer access points and likely won't ever be patched for older
devices. Because of this IWD must work around the problem which can
be eliminated by not sending out this commit message.
This bug was reported to the hostapd ML:
https://lists.infradead.org/pipermail/hostap/2021-September/039842.html
This change should not cause any compatibility problems to non-hostapd
access points and is identical to how wpa_supplicant treats this
scenario.
If a commit is received while in an accepted state the spec states
the scalar should be checked against the previous commit and if
equal the message should be silently dropped.
In netconfig_load_settings apply the DNS overrides strings we've loaded
instead of leaking them.
Fixes: ad228461ab ("netconfig: Move loading settings to new method, refactor")
netdev now assumes the SSID was set in the handshake (normally via
network_handshake_setup) but WSC calls netdev_connect directly so
it also should set the SSID.
In order to support OWE in the CMD_CONNECT path the scan_bss parameter
needs to be removed since this is lost after netdev_connect returns.
Nearly everything needed is also stored in the handshake except the
privacy capability which is now being mirrored in the netdev object
itself.
Use the MAC addresses for the gateways and DNS servers received in the
FILS IP Assigment IE together with the gateway IP and DNS server IP.
Commit the IP to MAC mappings directly to the ARP/NDP tables so that the
network stack can skip sending the corresponding queries over the air.
Send and receive the FILS IP Address Assignment IEs during association.
As implemented this would work independently of FILS although the only
AP software handling this mechanism without FILS is likely IWD itself.
No support is added for handling the IP assignment information sent from
the server after the initial Association Request/Response frames, i.e.
the information is only used if it is received directly in the
Association Response without the "response pending" bit, otherwise the
DHCP client will be started.
Add two methods that will allow station to implement FILS IP Address
Assigment, one method to decide whether to send the request during
association, and fill in the values to be used in the request IE, and
another to handle the response IE values received from the server and
apply them. The netconfig->rtm_protocol value used when the address is
assigned this way remains RTPROT_DHCP because from the user's point of
view this is automatic IP assigment by the server, a replacement for
DHCP.
Split loading settings out of network_configure into a new method,
network_load_settings. Make sure both consistently handle errors by
printing messages and informing the caller.
Setter which forces the use of group 19 rather than the group order
that ELL provides. Certain APs have been found to have buggy group
negotiation and only work if group 19 is tried first, and only. When
an AP like this this is found (based on vendor OUI match) SAE will
use group 19 unconditionally, and fail if group 19 does not work.
Other groups could be tried upon failure but per the spec group 19
must be supported so there isn't much use in trying other, optional
groups.
Handle the 802.11ai FILS IP Address Assignment IEs in Association
Request frames when netconfig is enabled. Only IPv4 is supported.
Like the P2P IP Allocation mechanism, since the payload format and logic
is independent from the rest of the FILS standard this is enabled
unconditionally for clients who want to use it even though we don't
actually do FILS in AP mode.
