The parser fully parses the IE and returns the version, Domain ID,
and PPS MO ID. This is meant to be used with an IE in scan results.
The builder only takes the version number, and assumes DGAF disabled,
and no Domain ID or PPS MO ID.
In the same fashion as the WSC WFA OUI, ie.[ch] will now expose the
other vendor OUIs to avoid duplication across multiple files in IWD
as well as used in iwmon.
The length check was incorrectly assuming that PPS MO ID or
ANQP Domain ID would be present in the IE. Both these are optional
and without then the minimum length is 5 bytes, not 7.
Parses up to 3 (the max) roaming consortium OIs out of the roaming
consortium IE. If more OIs are available via ANQP the 'num_anqp_out'
value will be set to indicate how many more OIs are available.
Builds according to the hotspot 2.0 spec using the vendor specific
IE.
The OSEN AKM is nearly identical to the RSN IE, but differs slightly.
For one, OSEN is encapsulated into the vendor specific IE, and includes
the WFA OUI before the 'normal' RSN elements. OSEN also does not include
a WPA version, since its not technically WPA/WPA2.
Some of the RSN parsing was made common so both RSN/OSEN parsing could
use it.
FT over FILS-SHA384 uses a 24 byte FT MIC rather than the 16 byte MIC
used for all other AKMs. This change allows both the FT builder/parser
to handle both lengths of MIC. The mic length is now passed directly
into ie_parse_fast_bss_transition and ie_build_fast_bss_transition
The TLV builder APIs were not very intuative, and in some (or all)
cases required access to the builder structure directly, either to
set the TLV buffer or to get the buffer at the end.
This change adds a new API, ie_tlv_builder_set_data, which both sets
the length for the current TLV and copies the TLV data in one go.
This will avoid the need for memcpy(ie_tlv_builder_get_data(...),...)
ie_tlv_builder_finalize was also changed to return a pointer to the
start of the build buffer. This will eliminate the need to access
builder.tlv after building the TLVs.
ie_tlv_builder_init was changed to take an optional buffer to hold
the TLV data. Passing NULL/0 will build the TLV in the internal
buffer. Passing in a pointer and length will build into the passed
in buffer.
For simplicity 160Mhz and 80+80Mhz were grouped together when
parsing the VHT capabilities, but the 80+80 bits were left in
vht_widht_map. This could cause an overflow when getting the
width map.
This adds support for parsing the VHT IE, which allows a BSS supporting
VHT (80211ac) to be ranked higher than a BSS supporting only HT/basic
rates. Now, with basic/HT/VHT parsing we can calculate the theoretical
maximum data rate for all three and rank the BSS based on that.
This adds HT IE parsing and data rate calculation for HT (80211n)
rates. Now, a BSS supporting HT rates will be ranked higher than
a basic rate BSS, assuming the RSSI is at an acceptable level.
The spec dictates RSSI thresholds for different modulation schemes, which
correlate to different data rates. Until now were were ranking a BSS with
only looking at its advertised data rate, which may not even be possible
if the RSSI does not meet the threshold.
Now, RSSI is taken into consideration and the data rate returned from
parsing (Ext) Supported Rates IE(s) will reflect that.
According to the specification, Supported rates IE is supposed
to have a maximum length of eight rate bytes. In the wild an
Access Point is found to add 12 bytes of data instead of placing
excess rate bytes in an Extended Rates IE.
BSS: len 480
BSSID 44:39:C4:XX:XX:XX
Probe Response: true
TSF: 0 (0x0000000000000000)
IEs: len 188
...
Supported rates:
1.0(B) 2.0(B) 5.5(B) 6.0(B) 9.0 11.0(B) 12.0(B) 18.0 Mbit/s
24.0(B) 36.0 48.0 54.0 Mbit/s
82 84 8b 8c 12 96 98 24 b0 48 60 6c .......$.H`l
DSSS parameter set: channel 3
03
...
Any following IEs decode nicely, thus it seems that we can relax
Supported Rates IE length handling to support this thermostat.
Since we use the special 0xffff value in the builder code, check that
the tag is not 0xffff in ie_tlv_builder_finalize before writing the
header. This is for consistency, not for a specific use case.
Make parsing TLVs using Extended Element IDs easier by returning the
extended tag value as listed in enum ie_type instead of just the 255
value, and not returning the pointer to the extended tag as the IE data
and instead the pointer to the next byte after the extended ID.
Parse the contents of the GTK and IGTK subelements in an FT IE instead
of working with buffers containing the whole subelement. Some more
validation of the subelement contents. Drop support for GTK / IGTK when
building the FTE (unused).
When parsing the EAPoL-Key key data field we don't strip the 0xdd /
0x00 padding from the decrypted data so there may be trailing padding
after the IE sequence and valgrind will report an invalid read of the
length byte. Same thing may happen if we're sent garbage.
Rosen Penev