Switch the command pattern to match the common command scheme
where the entity name (network name) follows the command family name:
From
known-network forget <network name>
To
known-network <network name> forget
In addition, it extracts the network match by name logic into its
own function for the further reusability. In the case of ambiguity
between the network objects with the same SSID but different security
types the logic asks to specify the security type in addition
to the network name as follows:
known-network <network name.security> forget
The handshake_state only holds a single AKM value. FILS depends on the AP
supporting EAP as well as FILS. The first time IWD connects, it will do a
full EAP auth. Subsequent connections (assuming FILS is supported) will use
FILS. But if the AP does not support FILS there is no reason to cache the
ERP keys.
This adds the supp_fils to the handshake_state. Now, station.c can set this
flag while building the handshake. This flag can later be checked when
caching the ERP keys.
This allows IWD to cache ERP keys after a full EAP run. Caching
allows IWD to quickly connect to the network later on using ERP or
FILS.
The cache will contain the EAP Identity, Session ID, EMSK, SSID and
optionally the ERP domain. For the time being, the cache entry
lifetimes are hard coded to 24 hours. Eventually the cache should
be written to disk to allow ERP/FILS to work after a reboot or
IWD restart.
mschaputil already had similar functionality, but ERP will need this
as well. These two functions will also handle identities with either
'@' or '\' to separate the user and domain.
Many operations performed during an error in load_settings were the same
as the ones performed when freeing the eap object. Add eap_free_common
to unify these.
EAP identites are recommended to follow RFC 4282 (The Network Access
Identifier). This RFC recommends a maximum NAI length of 253 octets.
It also mentions that RADIUS is only able to support NAIs of 253
octets.
Because of this, IWD should not allow EAP identities larger than 253
bytes. This change adds a check in eap_load_settings to verify the
identity does not exceed this limit.
Added handling for several FILS IEs and NL attributes specific to
FILS. Also changed "SAE Data" to "Auth Data" since its now used for
both SAE and FILS.
The associate event is only important for OWE and FT. If neither of
these conditions (or FT initial association) are happening we do
not need to continue further processing the associate event.
802.11 mandates that IEs inside management frames are presented in a
given order. However, in the real world, many APs seem to ignore the
rules and send their IEs in seemingly arbitrary order, especially when
it comes to VENDOR tags. Change this function to no longer be strict in
enforcing the order.
Also, drop checking of rules specific to Probe Responses. These will
have to be handled separately (most likely by the AP module) since
802.11-2016, Section 11.1.4.3.5 essentially allows just about anything.
In netdev_associate_event the ignore_connect_event was getting set true,
but afterwards there were still potential failure paths. Now, once in
assoc_failed we explicitly set ignore_connect_event to false so the
the failure can be handled properly inside netdev_connect_event
The list of PSK/8021x AKM's in security_determine was getting long,
and difficult to keep under 80 characters. This moves them all into
two new macros, AKM_IS_PSK/AKM_IS_8021X.
It was assumed that the hunt-and-peck loop was guarenteed to find
a PWE. This was incorrect in terms of kernel support. If a system
does not have support for AF_ALG or runs out of file descriptors
the KDFs may fail. The loop continued to run if found == false,
which is also incorrect because we want to stop after 20 iterations
regarless of success.
This changes the loop to a for loop so it will always exit after
the set number of iterations.
